Bedienungsanleitung Bellman BE1452 (Seite 4 von 4) (Englisch)

661647

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

If Try this

The receiver seems to be turned o

 The batteries are depleted. Replace them with 4 x 1.5V LR14 alkaline batteries.

The power LED is yellow when the

receiver is activated.

 The battery level is low. Replace them with 4 x 1.5V LR14 alkaline batteries.

The receiver does not respond

when a transmitter is activated, but

works when I use the test button

 Check the transmitter batteries and connections.

 Move the receiver closer to the transmitter to make sure it’s within radio range.

 Check that the receiver is set to the same radio key as the other units in the Visit

system, see Changing the radio key.

The receiver is activated for no

apparent reason

 There is probably another Visit system installed nearby that triggers your system.

Change the radio key on all units, see Changing the radio key.

The receiver is too silent

 Turn up the volume using the red volume dial on the top of the unit.

The receiver is not ashing

 Check that the ash signal switch on the back of the unit is set to the ON position.

Advanced programming

By using advanced programming, you can customize the signal pattern from a specic transmitter and event, displaying

the LED colour, sound and vibration pattern of your choice. The advanced programming overrides the radio key and pairs

the units via the serial number. Please note that smoke alarms cannot be programmed for safety reasons.

Note: The transmitter must be activated as it is intended to be used in the system to generate the right signal.

This means that you can’t always use the transmitter test button (see Default signal pattern for the relevant transmitter).

Here is how you program the receiver:

1 Press and hold the test button on the receiver. The green and yellow Visit LEDs will start to blink alternately.

While still holding down the button, activate the desired transmitter as intended. The power LED on the receiver will

light up in yellow to show that you are in advanced programming mode. Release the button.

2 Scroll through the dierent Visit LED options by pressing the test button on the receiver. Select the desired Visit LED

colour by holding down the test button until the power LED goes out and lights up again.

3 Scroll through the dierent sound options by pressing the test button on the receiver. Select the desired sound by

holding down the test button until the power LED goes out and lights up again.

4 Scroll through the dierent vibration options by pressing the test button on the receiver (bed shaker required).

Select the desired vibration pattern by holding down the test button until the power LED goes out and lights up again.

5 The receiver will now show the new Visit LED colour, sound and vibration pattern. Press the test button briey to end the

demonstration. After a short while, it will return to normal mode.

Deleting the advanced programming

Follow the procedure below to delete the advanced programming.

1 Hold down the test button on the receiver until the green and yellow Visit LEDs blink alternately. Release the button.

2 Press the test button on the receiver 3 times in quick succession.

3 All Visit LEDs will light up for ~2 seconds to show that it has been deleted.

Troubleshooting

Visit portable receiver

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bellman BE1452 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bellman BE1452

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info