Bedienungsanleitung Bellman Visit (Seite 4 von 4) (Englisch)

747162

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

If Try this

The receiver seems to be turned o

 The battery is depleted. Charge or replace it with a VARTA V40H NiMH battery.

The battery LED blinks in yellow

 The battery level is low. Charge or replace it with a VARTA V40H NiMH battery.

The receiver is not charging

 Check that the receiver is placed correctly in the charger and that the power supply

is connected. The mains LED and charging LED should be lit.

 Charge or replace the backup batteries with four 1.2 V NiMH rechargeable batteries.

The receiver does not respond

when a transmitter is activated

 Check the transmitter batteries and connections.

 Move the receiver closer to the transmitter to make sure it’s within radio range.

 Check that the receiver is set to the same radio key as the other units in the Visit

system, see Changing the radio key.

The receiver is activated for no

apparent reason

 There is probably another Visit system installed nearby that triggers your system.

Change the radio key on all units, see Changing the radio key.

The bed shaker does not vibrate

 Check that the bed shaker is connected and that the receiver is placed in the charger.

Advanced programming

By using advanced programming, you can customize the signal pattern from a specic transmitter and event, displaying

the LED colour and vibration pattern of your choice. The advanced programming overrides the radio key and pairs the

units via the serial number. Please note that smoke alarms cannot be programmed for safety reasons.

Note: The transmitter must be activated as it is intended to be used in the system to generate the right signal.

This means that you can’t always use the transmitter test button (see Default signal pattern for the relevant transmitter).

Here is how you program the wrist receiver:

1 Press and hold the function button on the receiver. The green and yellow Visit LEDs will start to blink alternately.

While still holding down the button, activate the desired transmitter as intended. The battery LED on the receiver lights

up in yellow to show that you are in advanced programming mode. Release the button.

2 Scroll through the dierent Visit LED options by pressing the function button on the receiver. Select the desired Visit

LED colour by holding down the function button until the battery LED goes out and lights up again.

3 Scroll through the dierent vibration options by pressing the function button on the receiver. Select the desired

vibration pattern by holding down the function button until the battery LED goes out and lights up again.

4 The wrist receiver will now show the new Visit LED colour and vibration pattern. Press the function button briey to end

the demonstration. After a short while, it will return to normal mode.

Deleting the advanced programming

Follow the procedure below to delete the advanced programming.

1 Hold down the function button on the receiver until the green and yellow Visit LEDs blink alternately. Release the button.

2 Press the function button on the receiver 3 times in quick succession.

3 All Visit LEDs will light up for ~2 seconds to show that it has been deleted.

Troubleshooting

Most problems with the wrist receiver can be solved quickly by following the advice below.

Visit wrist receiver

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bellman Visit Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info