Bedienungsanleitung Benekov S100 (Seite 13 von 30) (Englisch)

693646

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

- 13 -

Arrangement with 4 m feeder

4000 5820 2966 2374 114

Arrangement with 5 m feeder

5000 6805 3951 2374 -60

* Dimension "A" is specified by the client when ordering based on spatial layout of the specific

boiler room.

4.2. Control and safety elements of the boiler

Control and regulation of the boiler is ensured by a control unit - see separate instruction

manual.

Safety components that monitor the safe operation of the boiler:

• The emergency thermostat is used to prevent the system from overheating. The

manufacturer sets the thermostat at 95 °C, i.e. at a higher temperature than the setpoint that

can be set on the boiler. The emergency thermostat is positioned on the rear wall of the

boiler in the control unit cabinet.

• Thermal protection of the motor (thermal contact) is part of both fuel feeder motors and is

used to protect them from overheating in the case of fuel feeder blockage. It also

retroactively stops the fan, so as to avoid burning of the fuel in the container in the event of

a fault. During normal operation, the motor working temperature is up to 85 °C - such

warming does not mean a failure.

• The turnstile is a device that mechanically separates the fuel between the screw conveyors

(feeding from the bunker + feeding into the boiler). In the event of re-ignition of the fuel in

the boiler feeding (e.g. during power outage for a longer time) the fuel in the tank does not

ignite. Furthermore the turnstile serves as a partial fuel crusher, so in the event that a longer

piece reaches the turnstile, the turnstile crushes this piece into smaller ones.

• The cover limit switch of the bunker feeder shuts down the screw feeder and fan when the

cover is open. After its proper closure the boiler is put back into operation.

• The emergency fire extinguishing system is another security feature preventing burning of

fuel through to the container. A temperature increase above 95 °C at the feeding out of the

bunker results in thermostatic valve opening and the space is cooled with cooling water

from the water main.

• Firing flap is located between the second and the third draft in the top part of the boiler body

and serves to regulate the flue gas temperature at the boiler outlet.

When operating the boiler when the flue gas temperature is higher than 100 °C the firing

valve must be closed, i.e. firing flap lever on the side of the boiler must be rotated as much

as possible forwards and secured with a locking screw. When firing (with cold chimney) or

during long term operation of the boiler at lower output it is recommended to operate the

boiler with the firing valve slightly open so that the flue gas temperature does not drop

below 80 °C. In this case, the firing flap lever must be rotated downward (backwards) and

secured by a locking screw.

4.3. Boiler accessories

Standard accessories:

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Benekov S100 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info