Bedienungsanleitung Benekov S100 (Seite 27 von 30) (Englisch)

693646

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

Overall wear of the

screw shaft.

Replace the screw shaft.*

transported into the

combustion chamber.

The turnstile chain was

damaged.

Replace the turnstile chain.*

Boiler fan cable is

disconnected (or

damaged).

Connect (or replace) the boiler fan cable.* Boiler fan does not

work.

The fan is damaged. Replace the boiler fan.*

The fan was clogged by

dust.

Clean the boiler fan.* The fan is noisy in

operation.

The fan bearings are

worn.

Replace the entire boiler fan.*

The fan does not rotate

during boiler

modulation at the

lowest output values.

The set values of the fan

speed are too low.

Increase the fan speed on the boiler

controller so as to guarantee its smooth

operation.

Water from the

emergency fire-fighting

equipment leaked into

the fuel feeder.

The fuel burnt through

to the fuel feeder, which

activated the

thermostatic valve.

Remove wet fuel from the feeder, fill the

container with new dry fuel and start-up the

boiler.

Water from the

emergency fire-fighting

equipment leaks into

the fuel feeder.

The thermostatic valve

on the feeder leaks.

Replace the thermostatic valve.

The boiler is filled with

wet fuel.

Refill the container with dry fuel. The walls of the fuel

tank are covered with

droplets of water.

The temperature in the

boiler room is low

(about 12 °C or less)

The boiler room requires a higher air

temperature (boiler room wall insulation,

installation of heating radiator to the boiler

room, etc.).

A short time passed

after firing in the boiler.

Let the boiler thoroughly flame up.

Fuel dosing is set to a

lower output.

Adjust the fuel dosing according to the

control unit instruction manual.

The boiler cannot reach

the rated output during

operation.

The boiler uses non-

prescribed fuel (high

humidity, lower calorific

capacity, etc.)

Refill the container with prescribed fuel.

The boiler is clogged

with soot.

Clean the heat transfer surfaces of the boiler

body.

The boiler is

overheating.

Reduce fuel dosage.

High chimney draft. Install a chimney flue draw limiter (this

activity must be performed by a specialized

company).

Ceramic reflector is not

installed in the boiler

body.

Install a ceramic reflector according to the

instruction manual.

The flue gas

temperature is higher

than specified in the

instructions.

The firing flap in the

boiler body is open.

Close the firing flap using the cleaner lever

and firing flap and secure it with a locking

screw with a plastic head.

Low chimney draft. Have a chimneysweeper check the value of

the chimney draft. If the measured value is

less than the value required (see

instructions), it is necessary to make

adjustments to the chimney.

Smoke appears in the

boiler room or fuel

container.

The boiler door and / or

the top cover of the

boiler body and / or the

fuel tank cover is not

closed properly.

Duly close the boiler door and / or the top

cover of the boiler body and / or the fuel tank

cover properly.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Benekov S100 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info