Bedienungsanleitung Benekov S51 (Seite 29 von 39) (Englisch)

693641

Zoom out

Zoom in

Vorherige Seite

1/39

Nächste Seite

6.2. Verification activities before start-up

The following checks must be performed before start-up:

a) Filling the heating system with water

The water used for filling boiler and heating systems must be clear and colourless, without suspended

solids, oil and aggressive chemicals. Its hardness must comply with ČSN 07 7401: 1992 and it is

essential that in case the water hardness does not comply, it must be treated. Even multiple heating of

water with a higher hardness does not stop salt build-up on the walls of the exchanger. 1 mm of calcite

reduces the heat transfer from metal to water at the given point by approximately 10%.

Heating systems with an open expansion tank allow direct contact between the heating water and the

atmosphere. During the heating season the water expanding in the tank absorbs oxygen which increases

corrosion and at the same results in significant water evaporation. Refilling can only be performed with

water treated according to ČSN 07 7401:1992. The heating system must be thoroughly flushed in order to

wash out all impurities.

During the heating season it is necessary to maintain a constant volume of water in the heating system.

When refilling the heating system with water no air must be sucked into the system. The boiler and

heating system water must never be discharged or taken for use except in emergencies like repairs etc.

Water discharge and filling with new water increases the danger of corrosion and scaling.

If it is necessary to refill the heating system with water only do this when the boiler is cold to

prevent damage to the steel heat exchanger.

b) Heating system tightness

c) Connection of emergency fire-fighting equipment to the water distribution system

d) Connection to the chimney - must be approved by a chimney sweeping company

e) Ceramic reflector of BENEKOV S16 and S26 boilers (fig. no. 24, pos. 7) fitted into the combustion

chamber of the burner, i.e. laid on the obliquely welded beams (8) in the boiler body and attached to the

back wall of the combustion chamber.

Ceramic reflector of BENEKOV S51 boiler (fig. no. 25, pos. 7) fitted into the combustion chamber of the

burner, i.e. laid on the horizontally welded beams (8) in the boiler body and attached to the back wall of

the combustion chamber.

f) Electric connection

The assembly completion and heating test must be recorded in the "Guarantee certificate".

6.3. Putting into operation

1. Fire the boiler.

2. Bring the boiler to operating temperature. The recommended operating temperature of the output

heating water is 65 to 80 °C.

3. Check the boiler tightness again.

4. Carry out the heating test according to relevant standards (see the Guarantee certificate)

5. Acquaint the user with the boiler operation - see chapter 7.

6. Make a record in the Guarantee certificate.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Benekov S51 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info