Bedienungsanleitung Benning CC1 (Seite 9 von 30) (Deutsch, Englisch, Holländisch, Spanisch, Schwedisch)

577171

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

09/ 2003

BENNING CC 1



6. Environment conditions:

- The BENNING CC 1 is intended for making measurements in dry

environment.

- Maximum barometric elevation for making measurements: 2000 m,

- Overvoltage category IEC 60664/ IEC 61010, 300 V category III,

600 V category II,

- Contamination degree II according to EN 61010-1

- Protection class: IP 30 (EN 60529),

- Operating temperature and relative humidity:

For operating temperatures from 0 °C to 30 °C: relative humidity less than 80

For operating temperatures from 31 °C to 40 °C: relative humidity less than 75

For operating temperature from 41 °C to 50 °C: relative humidity less than 45 %

- Storage temperature: The BENNING CC 1 can be stored at any temperature

in the range from 20 °C to + 60 °C ).

7. Electrical specications

Note: The measuring precision is specied as the sum of

- a relative fraction of the measured value and

- a current value in A.

The measurement precision applies at a temperature of 23 °C ± 5 °C and a

relative humidity less than 75 %.

7.1 Alternating current measurement

Measurement

range

Measured

value

Output Measurement precision

400 A

3 A 3 mV

± (1,9 % + 0,5 A)

at 50 Hz - 60 Hz

30 A 30 mV

350 A 350 mV

400 A 400 mV

± (3,2 % + 1 A)

at 50 Hz - 60 Hz

Max. equivalent source resistance: 75 Ω

8. Making measurements with the BENNING CC 1

8.1 Preparations for making measurements

Operate and store the BENNING CC 1 only at the specied storage and

operating temperatures. Avoid continuous insulation.

- The nominal voltage and current ratings of the safety measuring cables

included in the scope of delivery correspond to the ratings of the

BENNING CC 1.

- The safety measuring cable is securely connected to the BENNING CC 1

and cannot be removed.

- Check the insulation of the safety measuring cables. Discard the

BENNING CC 1 immediately if the insulation is damaged.1

- Do not clamp the measuring pliers on a live conductor before the

BENNING CC 1 has not been connected to a multimeter.

Strong sources of interference in the vicinity of the BENNING CC 1 can lead

to unstable readings and measuring errors.

- Do not apply any voltage to the output contacts of the BENNING CC 1.



Do not exceed the maximum permitted voltage with respect to

earth potential! Electrical danger!

The highest voltage, that may be applied to the BENNING CC 1 against ground

potential, is 600 V.

8.2 Alternating current measurement

- Set the multimeter to the function “alternating voltage measurement” (V AC)

and select a measurement range that can display voltages from 1 mV to

400 mV.

- Contact the 4 mm safety connector of the spiral type safety measuring cable

with the COM jack of the multimeter.

- Contact the red 4 mm safety connector of the spiral type safety measuring

cable with the voltage input jack (V) of the multimeter.

- Opening lever



Operate and use meas. pliers to



clamp the single wire

live conductor.

- Read off the voltage value on the multimeter and convert to the current

value taking into account the conversion factor.

cc_1_in.indd 24.09.2003, 10:137

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Benning CC1 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info