Bedienungsanleitung Benning CC2 (Seite 8 von 39) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch, Schwedisch)

577172

Zoom out

Zoom in

Vorherige Seite

1/39

Nächste Seite

2. Safety note

The instrument is built and tested in accordance with

DIN VDE 0411 part 1/ EN 61010-1

DIN VDE 0411-2-032/ EN 61010-2-032

and has left the factory in perfectly safe technical state.

To maintain this state and ensure safe operation of the appliance tester, the user

must observe the notes and warnings given in these instructions at all times.



The unit may be used only in power circuits within the overvoltage

category III with a conductor for 600 V max. to earth .

Remember that work on electrical components of all kinds is

dangerous. Even low voltages of 30 V AC and 60 V DC may be

dangerous to human life.



Before starting the appliance tester up, always check it as well

as all cables and wires for signs of damage.

Should it appear that safe operation of the appliance tester is no longer possible,

it should be shut down immediately and secured to prevent it being switched

on accidentally.

It may be assumed that safe operation is no longer possible:

if the instrument or the measuring cables show visible signs of damage, or

- if the appliance tester no longer functions, or

- after long periods of storage under unfavourable conditions, or

- after being subjected to rough transport.



In order to avoid danger,

- do not touch the bare prod tips of the measuring cables

connectors,

- insert the measurement lines in the appropriately

designated measuring sockets on the multimeter

3. Scope of delivery

The scope of delivery for the BENNING CC 2 comprises:

3.1 One BENNING CC 2 with a rmly connected safety measuring line with

90° offset 4 mm safety connector,

3.2 One operating instructions manual

4. Description of appliance tester

The clamp-on adapter BENNING CC 2 is a measuring adapter for analog and

digital multimeters and is used for alternating current measurements up to

200 A.

See gure 1: Appliance front face

Moreover, the BENNING CC 2 current clamp adapter combined with the

BENNING IT 120 installation tester is appropriate for measuring load currents

from 0.5 A to 20 A.

The display and operator control elements specied in Fig. 1 are designated

as follows:



Measuring pliers, for clamping on the single wire alternating current

conductor.



Current probe bulge, protects against contact with conductor.



Opening lever, for opening and closing the measuring pliers.



Housing with label area



Safety measuring line with 4 mm safety connector, red, black, 90° offset.

5. General information

5.1 General details on the clamp-on adapter

Sensor type: Induction coil for measuring alternating current

5.1.1 Temperature coefcient of the measured value:

0.2 x (stated measuring precision)/ °C < 18 °C or > 28 °C, related to the

value for the reference temperature of 23° C.

5.1.2 Largest opening of pliers: 21 mm,

5.1.3 Maximum conductor diameter: 20 mm,

5.1.4 Appliance dimensions:

(L x W x H) = 135 x 50 x 30 mm

Appliance weight:

180 g

03/ 2007

BENNING CC 2



Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Benning CC2 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info