Bedienungsanleitung Benning CM11.0 (Seite 17 von 83) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch, Türkisch)

577177

Zoom out

Zoom in

Vorherige Seite

1/83

Nächste Seite

11/ 2014

BENNING CM 11



7.6 Continuity test

Open circuit-voltage: approx. 3 V, max. Testing current 1 mA

The built-in buzzer sounds when resistance is less than 100 Ω.

8. Measuring with the BENNING CM 11

8.1 Preparing the measurement

Operate and store the BENNING CM 11 at the specified storage and operating temperatures

only! Do not permanently expose the device to sunlight.

- Check rated voltage and rated current details specified on the safety meas uring lines. The

nominal voltage and current ratings of the safety measuring cables included in the scope of

delivery correspond to the ratings of the BENNING CM 11.

- Check the insulation of the safety measuring lead. If the insulation is damaged, the

BENNING CM 11 must be scrapped immediately.

- Check the continuity of the safety measuring leads. If the leads is discon nected at any point,

remove it immediately.

- Before - at the rotary switch

a different function is selected, the safety measuring leads

must be disconnected from the measuring point.

- Strong sources of interference in the vicinity of the BENNING CM 11 might involve unsta ble

readings and measuring errors.

8.2 Voltage measurement



Do not exceed the maximum permitted voltage with respect to earth potential!

Electrical danger!

The maximum voltage which may be applied to the sockets

- COM socket, black J,

- V- Ω socket (positive) K for voltage and resistance measurements and continuity testing

(marked red)

of the BENNING CM 11 against ground, amounts to 300 V.

- Use the rotary switch

to select the required function V or V on the BENNING CM 11.

- The black safety measuring lead has to be contacted with the COM jack J on the

BENNING CM 11.

- Connect the red safety measuring lead to the V-Ω jack K, marked in red.

- Bring the safety measuring leads into contact with the measuring points, read off measured

value on the digital display

on the BENNING CM 11.

Note:

- In small voltage measuring ranges, the zero-volt indication does not appear (due

to interference) when the safety measuring leads are open. Make sure that the

BENNING CM 11 is fully functional by short-circuiting the measuring tips.

See figure 2: DC voltage measurement

See figure 3: AC voltage measurement

8.3 Current measurement



Do not apply any voltage to the input jacks J and K of the BENNING CM 11!

Any possibly connected safety measuring leads have to be removed. For

direct current (DC) measurements, observe correct polarity! The arrow on the

measuring clamp indicates the technical current direction. +

→ –

Use the rotary switch

to select the required function A or A on the BENNING CM 11.

- Press the “ZERO” button

to set the BENNING CM 11 to the starting point.

- Operate opening lever



, clamp



single wire live conductor centrally by means of the

BENNING CM 11 current probe.

- Read off the digital display unit

See figure 4: AC/ DC current measurement

8.4 Resistance measurement

- Select the / Ω function by means of the rotary switch

of the BENNING CM 11 and press

the „MIN/MAX“ key

- The black safety measuring lead has to be contacted with the COM jack J on the

BENNING CM 11.

- Connect the red safety measuring lead to the V-Ω jack K, marked in red.

- Bring the safety measuring leads into contact with the measuring points, read off measured

value on the digital display

on the BENNING CM 11.

Note:

- To obtain a correct measurement, ensure that no voltage is applied to the measuring point.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Benning CM11.0 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info