Bedienungsanleitung Benning CM7 (Seite 17 von 117) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch, Türkisch, Schwedisch)

577183

Zoom out

Zoom in

Vorherige Seite

1/117

Nächste Seite

09/ 2013

BENNING CM 7



 COM jack, common socket for voltage, resistance measurement and con-

tinuity testing,

 Opening lever, for opening and closing the current probe.

 Bulge of current probe, protects against contact with conductor.



Measuring pliers, for clamping on the single wire current-carrying conductor.

 HOLD button, storage of the indicated measured value,

) This is what the automatic polarity indication for DC voltage refers to

5. General information

5.1 General details on the current probe multimeter

5.1.1 The digital display  is a 3 ¾- digit liquid crystal display with 14 mm

high numerals, complete with decimal point. The largest numerical

value which can be displayed is 4000.

5.1.2 The polarity indication  is automatic. Only one polarity with respect to

the socket marked “-” is indicated.

5.1.3 The overranging is indicated by “0L” or “- 0L” and, in part, an acoustic

warning.

Warning, no indication and prior warning in the event of an overload

condition!

5.1.4 Button (yellow)  switches on the display illumination. Shutdown is

effected by a renewed press of the button or automatically after 60

seconds.

5.1.5 ZERO key  (zero balance key)

Press the key to perform a zero balance for direct current (DC)

measurements. This can be used as well for differential measuring in

the resistance or frequency range. Indication by “REL” on the digital

display. Press the key again to indicate the stored difference (Offset).

The indication “REL” on the digital display is flashing. Press and hold

the key (approx. 2 seconds) to switch back to the measuring mode.

5.1.6 Measured value storage “HOLD”: Press the button “HOLD”  to store

the measured result. At the same time, the display shows the symbol

“HOLD”. A renewed press of the button switches back into measuring

mode.

5.1.7 The MIN/ MAX button function  inputs and stores automatically the

highest and lowest measured value. The following values are indicated

by button operation:

“MAX” indicates the stored maximum value, and “MIN” indicates the

lowest value. The continuous detection of the MAX-/ MIN value can

be stopped or started by pressing the button “HOLD” . Pressing the

button “MIN/MAX” for an extended period of time (2 seconds) switches

back into normal mode.

5.1.8 The button PEAK  (peak value storage) detects and stores the posi-

tive and negative peak/ crest value in the function V AC and A AC. At

the start of the measurement, press the button PEAK  for approx. 3

seconds in order to increase measurement precision and to fine-adjust

the BENNING CM 7. Pressing the button indicates the “PMAX” or

“PMIN” values in the display. An extended operation (2 seconds) of the

button PEAK  switches back into a standard mode.

5.1.9 The measuring rate of the BENNING CM 7 amounts nominally to 1.5

measurements per second for the digital display.

5.1.10 The BENNING CM 7 is switched on and off with the rotary switch .

Shutdown position “OFF”.

5.1.11 The BENNING CM 7 switches off automatically after approx. 30 minutes

(APO, Auto-Power-Off). It switches back on again if a button or the

rotary switch is operated. A buzzer tone signals automatic switchoff of

the appliance. The automatic switchoff can be deactivated by pressing a

button (except the button “HOLD”) and simultaneously switching on the

BENNING CM 7 from switch position “OFF”.

5.1.12 Temperature coefficient of the measured value: 0.2 x (stated measuring

precision)/ °C < 18 °C or > 28 °C, related to the value for the reference

temperature of 23 °C.

5.1.13

The BENNING CM 7

is supplied by a fitted 9 V block battery (IEC 6 LR 61)

5.1.14 If the battery voltage drops below the specified operating voltage of the

BENNING CM 7, then a battery symbol appears in the display.

5.1.15 The life span of a battery amounts to approx. 100 hours (alkali battery).

5.1.16 Appliance dimensions:

(L x W x H) = 275 x 105 x 51 mm

Appliance weight: 534 g

5.1.17 The safety measuring cables supplied are expressly suited for the rated

voltage and the rated current of the BENNING CM 7.

5.1.18 Largest opening of pliers: 53 mm

5.1.19 Largest cable diameter: 51 mm

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Benning CM7 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info