Bedienungsanleitung Benning Duspol Digital (Seite 7 von 83) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

577296

Zoom out

Zoom in

Vorherige Seite

1/83

Nächste Seite

01/2014

DUSPOL

digital



Operating Manual

DUSPOL

digital

Before using the DUSPOL

digital voltage tester, proceed as

follows: Please read the operating manual and absolutely ob-

serve the safety instructions!

Table of Contents

1. Safety instructions

2. Device description

3. Functional test before use to ensure the absence of

voltage of an installation

4. Checking the absence of voltage of an installation

5. Load connection with vibration motor

6. External conductor test (phase indication)

7. Phase sequence test

8. Continuity test

9. Resistance measurement

10. Diode test

11. Cable break detector

12. Measuring point / display illumination

13. Battery replacement

14. Technical data

15. General maintenance

16. Environmental protection

1. Safety instructions:

- During the use, touch the tester at the isolated handles L1

and L2

only and do not touch the probe tips L1/-

and L2/+

- Check the voltage tester for correct functioning immedi-

ately before and after using it in order to ensure the ab-

sence of voltage of an installation (see section 3)! Do not

use the voltage tester, if one or more indications are not

working or if it does not seem to be ready for operation!

Please repeat the test with another voltage tester after-

wards.

- With the battery being exhausted, the voltage tester is not

fully functional! From a voltage of AC/DC ≥ 50 V on, volt-

age tests are also possible without batteries by means of

the LED step indicator

. The LC display

is activated

with a minimum voltage ≥ 90 V AC/DC.

- The voltage tester must be used only within the stated

nominal voltage range and in electrical installations of up

to 1,000 V AC / 1,200 V DC!

- The voltage tester must be used only in electric circuits of

overvoltage category CAT III with max. 1,000 V or over-

voltage category CAT IV with max. 600 V for phase-to-

earth measurements.

- Do not operate the device with the battery compartment

being open.

- The voltage tester is designed for being used by qualified

electricians and under safe working conditions.

- The LED step indicator

is intended for indicating the

voltage range. It is not intended for measuring purposes.

- Creating a voltage tester for more than 30 seconds volt-

age (maximum duty cycle = 30 s)!

- Do not dismantle the voltage tester!

- The voltage tester must be protected against contamina-

tion and damaging of the housing surface.

- To protect them against damaging, provide the probe tips

with the enclosed probe tip protector

after using the

voltage tester!

Electrical symbols on the device:

Symbol Meaning



Important documentation!

The symbol indicates that the guide described

in the manual, to avoid any risks

Device or equipment for working under voltage

Push-button

Alternating voltage (AC)

Direct voltage (DC)

Direct and alternating voltage (DC/AC)

Earth (voltage to ground)

Phase sequence indication; the phase se-

quence can be indicated only at 50 or 60 Hz

and in an earthed mains

This symbol shows the orientation of the batter-

ies for inserting them with correct polarity

2. Device description

Probe tip protector

Probe tip L1/-

Probe tip L2/+

LED measuring point illumination

Sensor of the cable break detector

LC display

Push-button

Handle L1

Display handle L2

LED step indicator

Red LED  for external conductor test (phase indication)

Green LEDs ◄LR► of the phase sequence indication

(left/right)

Yellow LED Ω for continuity test (lights up)/cable break

detector (ashes)

Light sensor for LC display illumination

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Benning Duspol Digital Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info