Bedienungsanleitung Benning IT 101 (Seite 28 von 142) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Polnisch, Schwedisch)

577353

Zoom out

Zoom in

Vorherige Seite

1/142

Nächste Seite

02/ 2011

BENNING IT 101





Before opening the BENNING IT 101, make sure that it is free of

voltage! Electrical danger!

The BENNING IT 101 is protected against overload by an internal fuse (315 mA,

1000 V, 10 kA, FF, D = 6.3 mm, L = 32 mm).

Proceed as follows to replace the fuse:

- Disconnect the safety measuring leads from the measuring circuit.

- Disconnect the safety measuring leads from the BENNING IT 101.

- Turn the rotary switch J to the switch setting ”OFF”

- Remove the rubber protection frame N from the BENNING IT 101.

- Lay the BENNING IT 101 face down and release the screw of the battery

compartment cover.

- Lift the battery compartment cover off the bottom part.

- Lift one end of the defective fuse out of the fuse holder with the help of a

slot screwdriver.

- Lift the defective fuse completely out of the fuse holder.

- Insert a new fuse which has the same current rating, the same voltage

rating the same disconnecting rating, the same disconnecting characteristic

and the same dimensions.

- Make sure that the new fuse is located in the center of the holder.

- Lock the battery compartment cover into place on the bottom part and

tighten the screw.

- Place the BENNING IT 101 into the rubber protection frame N.

See figure 13: Battery and fuse replacement

9.5 Calibration

To maintain the specified accuracy of the measurement results, the instrument

must be recalibrated at regular intervals by our factory service. We recom-

mend a recalibration interval of one year. Send the appliance to the following

address:

Benning Elektrotechnik & Elektronik GmbH & Co. KG

Service Center

Robert-Bosch-Str. 20

D – 46397 Bocholt

9.6 Spare parts

Fuse FF 315 mA, 1000 V, 10 kA, D = 6.3 mm, L = 32 mm part no. 757213

10. Application of rubber protection frame

- You can store the safety measuring leads by winding the safety measuring

leads around the rubber protection frame N and engaging the tips of

the safety measuring leads with protection against the rubber protection

frame.

- You can engage a safety measuring lead to the rubber protection frame

such that the measuring tip protrudes freely, in order to be able to apply the

measuring tip - jointly with the BENNING IT 101 - to a measuring point.

- The rear support on the rubber protection frame provides for an inclined

set-up of the BENNING IT 101 (facilitates reading) or attachment.

- The rubber protection frame is fitted with a lug which can be freely used for

an attachment option.

See figure 14: Winding up the safety measuring leads

See figure 15: Erecting the BENNING IT 101

11. Environmental note

At the end of the product’s useful life, please dispose of the device at

collection points provided in your community.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Benning IT 101 Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info