Bedienungsanleitung Benning MM 1.2 (Seite 28 von 169) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch, Türkisch, Schwedisch)

577341

Zoom out

Zoom in

Vorherige Seite

1/169

Nächste Seite



BENNING MM 1-1/ 1-2/ 1-3.

- Bring the safety measuring leads into contact with the measuring points. If the

lead resistance between the COM jack J and the jack for V, , , Hz 9 falls

below 25 , the integrated buzzer of the BENNING MM 1-1/ 1-2/ 1-3 sounds.

See gure 8: Continuity test with buzzer

8.6 Capacitymeasurement (BENNING MM 1-2/ 1-3)



Beforeperformingcapacitymeasurements,dischargecapaci‑

torscompletely!

Neverapplyvoltagetothecapacitymeasurementjacks!

Thismightdamage ordestroythedevice!A damageddevice

might represent an electrical hazard!

- Select the desired function ( ) by means of the rotary switch 8 of the

BENNING MM 1-2/ 1-3.

- Determine the polarity of the capacitor and completely discharge the ca-

pacitor.

- Connect the black safety measuring lead to the COM jack J of the

BENNING MM 1-2/ 1-3.

- Connect the red safety measuring lead to the jack for V, , , Hz 9 of the

BENNING MM 1-2/ 1-3.

- Bring the safety measuring leads into contact with the discharged capacitor

according to ist polarity and read the measured value on the digital display

 of the BENNING MM 1-2/ 1-3.

See gure 9: Capacity measurement

8.7 Frequencymeasurement (BENNING MM 1-2/ 1-3)

- Select the desired function (Hz) by means of the rotary switch 8 of the

BENNING MM 1-2/ 1-3.

- Connect the black safety measuring lead to the COM jack J of the

BENNING MM 1-2/ 1-3.

- Connect the red safety measuring lead to the jack for V, , , Hz 9 of

the BENNING MM 1-2/ 1-3. Please observe the minimum sensitivity for fre-

quency measurements of the BENNING MM 1-2/ 1-3!

- Bring the safety measuring leads into contact with the measuring

points and read the measured value on the digital display  of the

BENNING MM 1-2/ 1-3.

See gure 10: Frequency measurement

8.8 Temperature measurement (BENNING MM 1-3)

- Select the desired function (°C or °F) by means of the rotary switch 8 of the

BENNING MM 1-3.

- Connect the temperature measuring adapter and the temperature meas-

uring lead to the COM jack (-) J and to the jack for V, , , Hz (+) 9

observing correct polarity.

- Arrange the end of the temperature measuring lead in the vicinity of the heat

source to be monitored. Read the measured value on the digital display 

of the BENNING MM 1-3.

See gure 11: Temperature measurement

8.9 Voltage indicator

The voltage indicator function is possible from each position of the rotary switch.

No measuring leads are required as voltage indicator (non-contact detection

of an alternating eld). The detector is located on the upper part of the device

behind the LED. By pressing the „VoltSensor“ key 5, the display indication dis-

appears (if the display is switched on). If a phase voltage is localized, this is

indicated by an acoustic signal and a red LED signal M. An indication is made in

earthed AC current networks only! The phase can be determined by means of a

single-pole measuring lead.

Practical hint:

Interruptions (cable breaks) in cables lying around openly such as e.g. cable

reels, fairy lights etc. can be traced from the feeding point (phase) to the point

of interruption.

Functional range: ≥ 230 V

See gure 12: Voltage indicator with buzzer

8.9.1 Phase test

- Connect the red safety measuring lead to the jack for V, , , Hz 9 of the

BENNING MM 1-1/ 1-2/ 1-3.

- Bring the safety measuring lead into contact with the measuring point of the

system part and press the „VoltSensor“ key 5.

- If the red LED lights and if there is an acoustic signal, the phase of an

earthed AC voltage is applied to this measuring point (system part).

09/ 2013

BENNING MM 1-1/ 1-2/ 1-3

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Benning MM 1.2 Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info