100301
48
Zoom out
Zoom in
Vorherige Seite
1/51
Nächste Seite
BenQ DC 5530 Users Manual
English
Tro ub leshoo ti ng
42
5 TROUBLESHOOTING
5.1 Error Message Table
Symptoms Causes Solutions
The power won’t turn
on.
The battery is out of power.
The AC power adapter is not con-
nected or is damaged.
Use the AC power adapter to charge
the battery.
Make sure the AC power is con-
nected and it's not damaged.
The power turns off
during use.
The battery is out of power.
Auto power off is enabled.
The battery/SD card cover is opened
when in use.
The adapter has not been connected
properly.
Use the AC power adapter to charge
the battery.
Switch on the power.
Do not open the battery/SD card
cover when the camera is in use.
Connect the adapter correctly.
The battery power is
being used up too
quickly.
The external temperature is too cold.
The battery is not used for a long
time.
Keep the camera away from extreme
temperatures.
Recharge the battery with AC power
adapter.
The camera does not
take pictures when the
shutter button is
pressed.
The camera is not set at Recording
Mode.
The battery is weak.
The power has not been switched
on.
Set the Mode Dial to Capture Mode.
Replace the battery.
Switch on the power.
The close-up image is
blurred.
Select the correct focus range. If the subject is within 15 cm, select
Macro mode.
The flash does not fire. The camera flash is turned off.
The light source is sufficient.
Set the flash mode to Auto Flash or
Forced Flash mode.
There is something
wrong with the color of
the captured image.
White balance is not set properly. Set the white balance to Auto mode
or other suitable mode.
The picture is too bright
or too dark.
There is excessive or inadequate
exposure.
Reset exposure compensation.
The LCD monitor is not
clear.
The LCD monitor plastic cover is
dirty.
You should clean the LCD cover.
The camera cannot
download images to the
PC.
Cable is not connected properly.
Camera is off.
There are no battery or the adapter
is not well connected.
OS is not Window 98SE
/2000/ME/XP or PC is not equipped
with USB port.
USB driver is not installed.
Check the cable connection.
Turn on the power.
Load new battery or check the AC
power adapter connection.
Install Windows 98SE/2000/ME/XP
and USB Port.
Install USB Driver.
48

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für BenQ DC S40 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von BenQ DC S40

BenQ DC S40 Bedienungsanleitung - Deutsch - 51 seiten

BenQ DC S40 Bedienungsanleitung - Holländisch - 51 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info