577256

BenQ GP30 LED Seite 10

10
Zoom out
Zoom in
Vorherige Seite
1/88
Nächste Seite
GP30
Ultra Lite LED Projector
User Manual
Table of contents2
Ta b l e o f c o n t e n t s
Important safety
instructions ................... 3
Introduction.................. 6
Projector features.....................................6
Shipping contents ......................................7
Projector exterior view...........................8
Controls and functions ............................9
Positioning your
projector ..................... 14
Obtaining a preferred projected
image size..................................................14
Connection ................. 16
Connecting the power...........................16
Connecting a computer.........................17
Connecting video source devices........19
Connecting an HDMI source device ..20
Connecting an MHL source device.....21
Connecting a component video
source device ...........................................22
Connecting a composite video
source device ...........................................23
Connecting an external speaker..........24
Connecting to an external memory
device.........................................................25
Playing sound through
the projector............................................26
Operation ................... 27
Starting up the projector ......................27
Switching input signal .............................28
Adjusting the projected image .............29
Hiding the image......................................30
Securing the projector...........................31
Firmware upgrade .................................. 33
Selecting the aspect ratio...................... 34
Optimizing the image............................. 35
Operating in a high altitude
environment............................................. 37
Adjusting the sound ............................... 37
Displaying images with PC and
video source devices.............................. 39
Using PC/ Video pop-up menus .......... 40
Displaying files with internal memory,
USB drive and SD card.......................... 44
Using USB streaming ............................. 56
Using wireless streaming ...................... 58
Setting up Wi-Fi Network.................... 69
Using settings menu ............................... 72
Shutting down the projector ............... 78
Maintenance ............... 79
Care of the projector............................ 79
Troubleshooting......... 81
Specifications.............. 82
Projector specifications......................... 82
Dimensions .............................................. 83
Timing chart............................................. 84
Warranty and Copyright
information................. 88
Important safety instructions 3
Important safety instructions
Your projector is designed and tested to meet the latest standards for safety of information
technology equipment. However, to ensure safe use of this product, it is important that
you follow the instructions mentioned in this manual and marked on the product.
Safety Instructions
1. Please read this manual before
you operate your projector. Save
it for future reference.
2. Do not look straight at the
projector lens during operation.
The intense light beam may damage
your eyes.
3. Refer servicing to qualified
service personnel.
4. In some countries, the line voltage is
NOT stable. This projector is
designed to operate safely within a
mains voltage of 19 volts DC, but
could fail if power cuts or surges of
10 volts occur. In areas where the
mains voltage may fluctuate or
cut out, it is recommended that
you connect your projector
through a power stabilizer, surge
protector or uninterruptible
power supply (UPS).
5. Do not block the projection lens with
any objects when the projector is
under operation as this could cause
the objects to become heated and
deformed or even cause a fire.
Important safety instructions4
Safety Instructions (Continued)
6. Never replace any electronic
components unless the projector is
unplugged.
7. Do not place this product on an
unstable cart, stand, or table. The
product may fall, sustaining serious
damage.
8. Do not attempt to disassemble this
projector. There are dangerous high
voltages inside which may cause
death if you should come into
contact with live parts. Refer
servicing only to suitably qualified
professional service personnel.
9. When the projector is under
operation, you may sense some
heated air and odor from its
ventilation grill. It is a normal
phenomenon and not a product
defect.
10. Do not place this projector in any
of the following environments.
- Space that is poorly ventilated or
confined. Allow at least 50 cm
clearance from walls and free flow of
air around the projector.
- Locations where temperatures may
become excessively high, such as the
inside of a car with all windows rolled
up.
- Locations where excessive humidity,
dust, or cigarette smoke may
contaminate optical components,
shortening the projector's life span
and darkening the image.
Important safety instructions 5
Safety Instructions (Continued)
- Locations near fire alarms
- Locations with an ambient temperature
above 40°C / 104°F
- Locations where the altitudes are higher
than 3000 m (10000 feet).
11. Do not block the ventilation holes.
- Do not place this projector on a blanket,
bedding or any other soft surface.
- Do not cover this projector with a cloth
or any other item.
- Do not place inflammables near the
projector.
If the ventilation holes are seriously
obstructed, overheating inside the
projector may result in a fire.
12. Always place the projector on a level,
horizontal surface during operation.
13. Do not stand the projector on end
vertically. Doing so may cause the
projector to fall over, causing injury or
resulting in damage to the projector.
14. Do not step on the projector or place
any objects upon it. Besides probable
physical damage to the projector,
doing so may result in accidents and
possible injury.
15. Do not place liquids near or on the
projector. Liquids spilled into the
projector may cause it to fail. If the
projector does become wet,
disconnect it from the power outlet
and call BenQ to have the projector
serviced.
3000 m
(10000 feet)
0 m
(0 feet)
Introduction
6
Introduction
Projector features
The projector integrates high-performance optical engine projection and a user-friendly
design to deliver high reliability and ease of use.
The projector offers the following features.
• Advanced LED light source
Long lasting LEDs provides a longer life span than traditional lamps.
• Optical engine with DLP technologies
WXGA resolution and a bright picture.
• Wireless Display
Supports wireless projection for PC (Windows and MAC) and mobile devices (iOS,
Android).
•SRS WOW HD
™ technology
Significantly improves the audio playback quality with deeper bass tones and
high frequency clarity for crisper detail.
• Various useful features
Supports iPhone/iPad, android devices, multimedia players, document viewer, internal
memory, SD card, USB flash drive, and USB display.
•Easy to carry
The projector is small and light, making it useful for business trips and leisure activities.
You can view documents, videos and photos anywhere.
• Multiple input ports
Multiple input ports, including PC, AV, HDMI/MHL, USB, and SD card provide flexible
connectivity with peripheral devices.
• Audio input & output
Equipped with 3W x 2 speakers with RCA & mini-jack input ports and phone jack
output port.
• Convenient menu items
Friendly menu is used for all types of inputs, making the projector easy to use.
• The apparent brightness of the projected image will vary depending on the ambient lighting
conditions, selected input signal contrast/brightness settings, and is proportional to
projection distance.
• The lamp brightness will decline over time and may vary within the lamp manufacturers
specifications. This is normal and expected behavior.
Introduction
7
Shipping contents
Carefully unpack and verify that you have all of the items shown below. If any of these items
are missing, please contact your place of purchase.
Standard accessories
The supplied accessories will be suitable for your region, and may differ from those illustrated.
*The warranty card is only supplied in some specific regions. Please consult your dealer for
detailed information.
User manual and wireless dongle manual are inside the projector’s internal memory. You can
view them directly in "Home screen/Internal memory/Document" via projector or use USB
cable to link PC/notebook and projector device and choose "Home screen/USB streaming/USB
File transfer". Meanwhile, the projector will be treated as external storage and you can access
user manual and wireless dongle manual via PC/Notebook.
Projector Power cord VGA cable
Quick start guide Warranty card* MHL cable
Pull the tab before using
the remote control.
Remote control with
battery
Wi-Fi dongle
Q
uick Start Guid
e
Mini Projector
Introduction
8
Projector exterior view
Do not block the ventilation openings. Blocking the ventilation openings can cause your
projector to overheat and may cause it to fail.
1. Vent (cold air intake)
2. Internal Speakers
3. Vent (heated air exhaust)
4. Front IR remote sensor
5. Projection lens
6. Lens cover
7. External control panel
(See "Projector" on page 9 for
details.)
8. Focus ring
9. AC power jack
10. Type A USB jack
11. SD card slot
12. Mini-B USB jack
13. HDMI / MHL input jack
14. RGB (PC)/Component Video
(YPbPr/ YCbCr) signal input jack
15. Video input jack
16. Audio input jack
17. Audio output jack
18. Kensington anti-theft lock slot
19. Adjuster feet
20. Tripod socket
3
4
1
2
5
6
3
1
2
7
8
Front/upper side
10
11
9
12
13 14 15 16 17
18
19
20
19
Introduction
9
Controls and functions
Projector
4. Left key
When the On-Screen Display (OSD)
menu is on:
- Navigate left to select the desired menu
items.
- Make adjustments. (e.g. brightness,
contrast, etc.)
When the On-Screen Display (OSD)
menu is off: (Only applied to SD card,
internal memory and USB Drive)
- Play previous video and audio file.
- Press and hold to rewind video and
audio file.
5. OK/Blank
Short press:
- Confirms a selected function when a
menu is displayed.
- Plays or pauses a video, music, photo
slideshow. (Only applied to SD card,
internal memory and USB Drive)
Long press (3 seconds):
To g g l e s t h e B l a n k .
6. Menu
Turns on the Pop-up setting menu.
7. Down/Volume down key
When the On-Screen Display (OSD)
menu is on:
- Navigate to down to select the desired
menu items.
- Make adjustments. (e.g. manual,
keystone, etc.)
When the On-Screen Display (OSD)
menu is off:
- Reduces the projector volume level.
1. POWER indicator light
Lights up or flashes when the projector is
under operation.
2. Power
Toggles the projector between standby
mode and on.
See "Starting up the projector" on page 27
and "Shutting down the projector" on page
78 for details.
3. Up/Volume up key
When the On-Screen Display (OSD)
menu is on:
- Navigate up to select the desired menu
items.
- Make adjustments. (e.g. manual, keystone,
etc.)
When the On-Screen Display (OSD) menu
is off:
- Magnifies the projector volume level.
2
4
10
3
6
5
7
9
8
1
11
12
I
I
Introduction
10
Keypad functions are not available when an MHL source is selected. When using MHL as input
source, please use remote control or your MHL device for operation.
8. Temperature indicator light
Lights up red if the projector's
temperature becomes too high.
9. LED indicator light
Indicates the status of the light source.
Lights up or flashes when the light source
has developed a problem.
10. Home
Directly returns to home screen from
lower level of OSD.
Exits application/pop-up message and back
to home screen directly.
11. Right key
When the On-Screen Display (OSD) menu
is on:
- Navigate right to select the desired menu
items.
- Make adjustments. (e.g. brightness,
contrast, etc.)
When the On-Screen Display (OSD) menu
is off: (Only applied to SD card, internal
memory and USB Drive)
- Play next video and audio file.
- Press and hold to fast-forward video and
audio file.
12. Back
Goes back to previous OSD menu, exits
and saves menu settings.
Introduction
11
Remote control
1. POWER
Toggles the projector between standby
mode and on. See "Starting up the
projector" on page 27 and "Shutting down
the projector" on page 78 for details.
2. Mute
Toggles projector audio between on and
off.
3. Up key
When the On-Screen Display (OSD)
menu is on:
- Navigate up to select the desired menu
items.
- Make adjustments. (e.g. manual
keystone, etc.)
When the On-Screen Display (OSD) is
off:
- Magnifies the projector volume level.
4. Left key
When the On-Screen Display (OSD)
menu is on:
- Navigate left to select the desired menu
items.
- Make adjustments. (e.g. brightness,
contrast, etc.)
When the On-Screen Display (OSD)
menu is off: (Only applied to SD card,
internal memory and USB Drive)
- Plays previous video, music, photo
slideshow or document.
- Press and hold to rewind video and
audio file.
5. Down key
When the On-Screen Display (OSD)
menu is on:
- Navigate to down to select the desired
menu items.
- Make adjustments. (e.g. manual
keystone, etc.)
When the On-Screen Display (OSD) is
off:
- Reduces the projector volume level.
6. Menu
Turns on or off the Pop-up setting menu.
7. Home
Directly returns to home screen from
lower level of OSD.
Exits application/pop-up message and
back to home screen directly.
8. Prev.
Plays previous video, audio, photo
slideshow or document file. (Only
applied to SD card, internal memory,
USB Drive and MHL)
9. Play
Plays or pauses video, music or photo
slideshow. (Only applied to SD card,
internal memory, USB Drive and MHL)
1
2
3
5
7
9
4
6
8
14
13
12
11
10
16
17
18
19
15
I
I
Introduction
12
Certain remote control functions might not work under MHL operation because the MHL
device being used may not support these functions. Please check your MHL device for available
functions.
10. Rewind
Rewinds video and audio file. (Only applied
to SD card, internal memory, USB Drive
and MHL)
11. Auto
Automatically determines the best picture
timings for the displayed computer image.
See "Auto-adjusting the image" on page 29
for details.
12. Volume up key
Magnifies the volume level.
13. Volume down key
Reduces the volume level.
14. Right Key
When the On-Screen Display (OSD) menu
is on:
- Navigate right to select the desired menu
items.
- Make adjustments. (e.g. brightness,
contrast, etc.)
When the On-Screen Display (OSD) menu
is off: (Only applied to SD card, internal
memory and USB Drive)
- Plays next video, music, photo slideshow
or document.
- Press and hold to fast-forward video and
audio file.
15. OK/Blank
Short press:
- Confirms a selected function when a
menu is displayed.
- Plays or pauses video, music, or photo
slide show. (Only applied to SD card,
internal memory and USB drive)
Long press (3 seconds):
- Toggles Blank on and off. See "Hiding the
image" on page 30 for details.
16. Back
Returns to upper level of OSD.
Closes pop-up setting menu of OSD.
Returns to home screen.
Leave current application of OSD.
17. Next
Plays next video, audio, photo slideshow
or document. (Only applied to SD card,
internal memory, USB Drive and MHL)
18. Fast-forward
Fast-forwards video and audio file. (Only
applied to SD card, internal memory,
USB Drive and MHL)
19. Pause
Pauses video and audio file. (Only applied
to SD card, internal memory, USB Drive
and MHL)
Introduction
13
Remote control effective range
Infra-Red (IR) remote control sensor is located on
the front of the projector. The remote control must
be held at an angle within 15 degrees perpendicular
to the projector's IR remote control sensor to
function correctly. The distance between the remote
control and the sensor should not exceed 7 meters
(~ 23 feet).
Make sure that there are no obstacles between the
remote control and the IR sensor on the projector
that might obstruct the infra-red beam.
Replacing the remote control battery
1. Pull out the battery holder.
Please follow the illustrated instructions. Push and hold
the locking arm while pulling out the battery holder.
2. Insert the new battery in the holder. Note the
positive polarity should face outward.
3. Push the holder into the remote control.
• Avoid excessive heat and humidity.
• There may be battery damage if the battery is
incorrectly replaced.
• Replace only with the same or equivalent type recommended by the battery manufacturer.
• Dispose of the used battery according to the battery manufacturer’s instructions.
• Never throw battery into a fire. There may be danger of an explosion.
• If the battery is dead or if you do not plan to use the remote control for a long time, remove
the battery to prevent damage to the remote control from possible battery leakage.
A
p
p
r
o
x
.
1
5
°
Positioning your projector
14
Positioning your projector
Obtaining a preferred projected image size
The distance from the projector lens to the screen, the zoom setting (if available), and the
video format each factors in the projected image size.
16:10 is the native aspect ratio of this projector.
The projector should always be placed horizontally level (like flat on a table), and
positioned directly perpendicular (90° right-angle square) to the horizontal center of the
screen. This prevents image distortion caused by angled projections (or projecting onto
angled surfaces).
The modern digital projector does not project directly forward (like older style reel-to-
reel film projectors did). Instead, digital projectors are designed to project at a slightly
upward angle above the horizontal plane of the projector. The projector can be readily
placed on a table, and the position of its projection will be forward and upward on a screen
so the bottom edge of the screen is above the level of the table (and everyone in the room
can see the screen).
If the projector is positioned further away from the screen, the projected image size
increases, and the vertical offset also increases proportionately.
When determining the position of the screen and projector, you will need to account for
both the projected image size and the vertical offset dimension, which are proportional to
the projection distance.
BenQ has provided a table of screen size to assist you in determining the ideal location for
your projector. Refer to "Projection dimensions" on page 15 for details. There are two
dimensions to consider, the perpendicular horizontal distance from the center of the
screen (projection distance), and the vertical offset height of the projector from the
horizontal edge of the screen (offset).
16:10 aspect image scaled to a 4:3 aspect
display area
Positioning your projector
15
Projection dimensions
Refer to "Dimensions" on page 83 for the center of lens dimensions of this projector
before calculating the appropriate position.
All measurements are approximate and may vary from the actual sizes. BenQ recommends that
if you intend to permanently install the projector, you should physically test the projection size
and distance using the actual projector in situ before you permanently install it, so as to make
allowance for this projector's optical characteristics. This will help you determine the exact
mounting position so that it best suits your installation location.
Screen Size
Projection distance in mmDiagonal
W (mm) H (mm)
Inches mm
30 762 646 404 750
40 1016 862 538 1000
50 1270 1077 673 1250
60 1524 1292 808 1500
80 2032 1723 1077 2000
100 2540 2154 1346 2500
120 3048 2585 1615 3000
150 3810 3231 2019 3750
200 5080 4308 2692 5000
220 5588 4739 2962 5500
250 6350 5385 3365 6250
300 7620 6462 4039 7500
1280:800 screen diagonal
Projection distance
Center of lens
Screen
Connection
16
Connection
In the connections shown below, some cables may not be included with the projector (see
"Shipping contents" on page 7). They are commercially available from electronics stores.
Connecting the power
1. Insert one end of the provided power cord into the AC IN terminal.
2. Insert the plug on the power cord into a power outlet. Check that the Power LED
indicator on the projector lights orange when using the AC adapter.
Connection
17
Connecting a computer
The projector provides a VGA input socket that allows you to connect it to both IBM
®
compatibles and Macintosh
®
computers. A Mac adapter is needed if you are connecting
legacy version Macintosh computers.
To connect the projector to a notebook or desktop computer:
• Using a VGA cable
1. Take the supplied VGA cable and connect one end to the D-Sub output socket of the
computer.
2. Connect the other end of the VGA cable to the COMPUTER socket on the
projector.
3. If you wish to make use of the projector speaker, take a suitable audio cable and
connect one end of the cable to the audio output socket of the computer, and the
other end to the audio input socket on the projector.
Many notebooks do not turn on their external video ports when connected to a projector.
Usually a key combo like FN + F3 or CRT/LCD key turns the external display on/off. Locate a
function key labeled CRT/LCD or a function key with a monitor symbol on the notebook. Press
FN and the labeled function key simultaneously. Refer to your notebook's documentation to find
your notebook's key combination.
Notebook or desktop computer
VGA cable
Audio
cable
Connection
18
• Using an HDMI cable
1. Take an HDMI cable and connect one end to the HDMI output jack of the computer.
2. Connect the other end of the HDMI cable to the HDMI jack on the projector.
• Using a USB cable
1. Take a USB cable and connect the type A end to the USB output jack of the
computer.
2. Connect the mini-B type end of the USB cable to the mini-B USB jack on the
projector. When you connect the projector to a computer, you can display
computer’s image or transfer files from your computer to the internal memory of the
projector.
3. If you select USB Display, follow the on-screen message to install the USB driver in
your computer first.
4. If you select USB File Transfer, go to My Computer or Windows Explorer to access
the projector's files. The projector appears as a Removable Disk. Transfer the files
from your computer to the projector by dragging and dropping or copying and
pasting.
To disconnect the projector from a computer:
i. Click on the Windows Taskbar.
ii. Click the pop-up message.
Connection
19
iii. Disconnect the USB cable only when the message says it is safe to remove the
hardware.
• Do not disconnect the USB cable while the files are being copied, as this could result in loss
of data or damage to the projector.
• The connection will not end if you have projector files open on the computer. Close all
projector files and try again.
• Other versions of Windows operate similarly. Follow the correct procedure for removing a
USB device from your computer safely for your version of Windows.
Connecting video source devices
You only need to connect the projector to a video source device using just one of the
above connecting methods; however, each provides a different level of video quality. The
method you choose will most likely depend upon the availability of matching terminals on
both the projector and the video source device as described below:
If the selected video image is not displayed after the projector is turned on and the correct video
source has been selected, check that the video source device is turned on and operating
correctly. Also, check and confirm that the signal cables have been connected correctly.
Te r m i n a l n a m e Terminal appearance Picture quality
HDMI / MHL HDMI / MHL Best
Component Video VGA Better
Video Video Good
Connection
20
Connecting an HDMI source device
The projector provides an HDMI input jack that allows you to connect it to an HDMI
source device like a Blu-Ray player, a DTV tuner or a display.
HDMI (High-Definition Multimedia Interface) supports uncompressed video data
transmission between compatible devices like DTV tuners or Blu-Ray player, and transmits
signal over a single cable. It provides pure digital viewing and listening experience.
Examine your video source device to determine if it has a set of unused HDMI output jacks
available:
• If so, you can continue with this procedure.
• If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to an HDMI source device:
1. Take an HDMI cable and connect one end to the HDMI output jack of the HDMI
source device.
2. Connect the other end of the HDMI cable to the HDMI jack on the projector.
• The HDMI cable (shown in this example) for connecting your video output device is not
supplied as standard accessory.
• The Apple Digital AV Adapter can be purchased from www.apple.com
.
Connection
21
Connecting an MHL source device
This projector supports MHL devices (MHL-enabled) through the use of HDMI input jack.
You can connect your MHL-enabled mobile device to the projector with an MHL cable to
play high-definition video with fluidity.
MHL (Mobile High-definition Link) supports uncompressed HD video (1080/30p) and
audio (7.1 surround sound) transmission between compatible devices like mobiles phones,
tablets and other portable consumer electronics devices and transmits signal over a single
cable. It provides pure digital viewing and listening experience.
Examine your mobile device to determine if it is MHL-enabled:
• If so, you can continue with this procedure.
• If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to an MHL source device:
1. Take an MHL cable and connect the MHL end to the MHL output jack of the MHL
source device.
2. Connect the HDMI end of the MHL cable to the HDMI/MHL jack on the projector.
Not all mobile devices are MHL-enabled, consult with your mobile device dealer to verify MHL
capabilities.
Connection
22
Connecting a component video source device
Examine your video source device to determine if it has a set of unused component video
output sockets available:
• If so, you can continue with this procedure.
• If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to a component video source device:
1. Take a component video to VGA (D-Sub) adaptor cable and connect the end with 3
RCA type connectors to the component video output sockets of the video source
device. Match the color of the plugs to the color of the sockets; green to green, blue
to blue, and red to red.
2. Connect the other end to the COMPUTER socket on the projector.
3. If you wish to make use of the projector speaker, take a suitable audio cable and
connect one end of the cable to the audio output sockets of the video source device,
and the other end to the audio input socket on the projector.
• When audio output jack is connected with the earphone or external speaker, the sound will
not come out from the projector speaker.
• No sound will come out from the speaker or audio output jack if video signals are not input.
Besides, the sound cannot be adjusted either.
Audio cable
AV device
Component Video to VGA
(D-Sub) adaptor cable
Connection
23
Connecting a composite video source device
Examine your video source device to determine if it has a set of unused composite video
output sockets available:
• If so, you can continue with this procedure.
• If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to a composite video source device:
1. Take a video cable and connect one end to the composite video output socket of the
video source device.
2. Connect the other end of the video cable to the VIDEO jack on the projector.
3. If you wish to make use of the projector speaker, take a suitable audio cable and
connect one end of the cable to the audio output sockets of the video source device,
and the other end to the audio input socket on the projector.
You need only to connect this device with a composite video cable if component video input is
unavailable. See "Connecting video source devices" on page 19 for details.
Video cable
Audio cable
AV device
Connection
24
Connecting an external speaker
You can hear sound through an external speaker instead of the internal speakers built into
the projector.
To connect the projector to an external speaker source device:
1. Connect an appropriate stereo cable to the external speaker and the audio output
jack on the projector.
When the audio cable is connected to the audio output jack, the internal speaker is muted.
Connection
25
Connecting to an external memory device
Connecting an SD card
To connect the projector to an SD card:
Connect an SD card to the SD card slot on the projector.
• The maximum memory capacity supported for an SD(HC) card is 32 GB. (The maximum
capacity supported for external memory is based on our factory test. Your experience may
differ depending on the manufacturer of the memory device.)
• The projector may not be compatible with some SD cards.
Connecting a USB storage device
To connect the projector to a USB storage device:
Plug the USB storage device into the Type A USB socket.
• This product supports USB memory device and HDD (Hard Disk Drive). Only the partition
that was most recently used will be mounted. (The maximum capacity supported for
external memory is based on our factory test. Your experience may differ depending on the
manufacturer of the memory device.)
• The Type A USB port provides up to 500 mA of power for HDDs when connected to this
projector. In the event that large capacity HDDs cannot be read by this projector, it may be
due to insufficient power. In this case, connect the HDD to an external power source with a
Y-type USB cable to provide HDD with extra power.
• This product does not support multi-card readers.
• This product does not work if the USB storage device is connected by a USB HUB.
• Products that do not comply with standard USB specifications might not operate normally.
(USB flash drive)
Connection
26
• A USB storage device with an automatic recognition application or its own driver might not
operate normally.
• A USB storage device that uses only a designated driver might not be recognized.
• Recognition speed for USB storage device may vary by device.
• Do not turn off the product or pull a connected USB storage device out while the USB
storage device is in use. Doing so may result in damage to the USB storage device or stored
file.
• Use a USB storage device which contains normal files. Abnormal files can cause a
malfunction or the files may not play.
• USB storages must be formatted in FAT16/FAT32/NTFS. FAT32 and NTFS are
recommended for HDD (Hard Disk Drive).
• As the data in the USB storage device can be damaged, please back up important data to
avoid loss. The user is responsible for data management. BenQ shall not be held liable for
any data loss.
• File tree in USB storage should be as simple as possible. Too many or too many layers of
folders will result in lag of access time.
• If an external memory device does not operate after you have connected it to the projector,
try to connect it to a PC. If it still does not operate normally, contact the memory device
manufacturer service center or related customer center.
Playing sound through the projector
You can make use of the projector speaker in your presentations, and also connect
separate amplified speakers to the audio output jack of the projector.
The table below describes the connection methods for different devices, and where the
sound is from.
• The selected input signal determines which sound will be played by the projector speaker,
and which sound will be output from the projector when audio output jack is connected.
• There’s no need to connect to an audio input jack because the projector can play the sound
from an HDMI / MHL, external memory and iPhone/iPad source device. However, you can
connect to an external device to play the sound.
• USB display does not support audio function.
Device PC/Component video Video
Audio input jack
Audio input (L/R)
AUDIO-IN
Audio input (L/R)
The projector can play the
sound from...
Audio input (L/R)
AUDIO-IN
Audio input (L/R)
Audio output jack
Operation
27
Operation
Starting up the projector
1. Connect the power using the power cord. The Power indicator turns into orange.
2. Press Power on the projector or remote
control to start the projector. The Power
indicator lights green when the projector is
on.
The start up procedure takes several seconds.
In the later stage of start up, a startup logo is
projected.
(If necessary) Rotate the focus ring to adjust
the image clearness.
3. If the projector is activated for the first time, select your OSD language following the
onscreen instructions.
4. If you are prompted for a password, press the
arrow keys to enter a six digit password. See
"Utilizing the password function" on page 31
for details.
5. Switch all of the connected equipment on.
6. The projector will display the home screen.
If the frequency/resolution of the input signal exceeds
the projector's operating range, you will see the
message 'Out of Range' displayed on a blank screen.
Please change to an input signal which is compatible with the projector's resolution or set the
input signal to a lower setting. See "Timing chart" on page 84 for details.
I
I
Operation
28
Switching input signal
Selecting an input source
The projector can be connected to multiple devices
at the same time. However, it can only display one
full screen at a time. Press / on the projector
or remote control to select your desired input
signal.
• The input signal type affects the options available
for the Picture Mode. See "Selecting a picture
mode" on page 35 for details.
• The native display resolution of this projector is in
16:10 aspect ratio. For best display picture results, you should select and use an input signal
outputting at this resolution. Any other resolutions will be scaled by the projector
depending upon the 'aspect ratio' setting, and this may result in image distortion or loss of
picture clarity. See "Selecting the aspect ratio" on page 34 for details.
Setting quick auto search
To set your projector to automatically search for input signals:
1. Go to Settings > Basic > Quick Auto Search menu, press OK, and a pop-up
menu appears.
2. Select On and press OK.
3. To leave the OSD menu, press or .
Changing color space
In the unlikely event that you connect the projector to a DVD player via the projector’s
HDMI input and the projected picture displays wrong colors, please change the color space
to YUV.
1. Press and press to highlight Color Space Conversion and press OK, a pop-
up menu appears.
2. Select a suitable color space and press OK.
This function is only available when the HDMI input port is in use.
Operation
29
Adjusting the projected image
Adjusting the image height
The projector is equipped with 2 adjuster feet. These adjusters change the image height.
To adjust the projector:
• Screw the adjuster feet to adjust the image
height.
• To retract the feet, screw the adjuster feet in
reverse direction.
If the projector is not placed on a flat surface or
the screen and the projector are not
perpendicular to each other, the projected image
becomes trapezoidal. To correct this situation, see
"Correcting keystone" on page 30 for details.
• Do not look into the lens while the lamp is on. The strong light from the lamp may cause
damage to your eyes.
• Be careful when you screw the adjuster foot as it is close to the exhaust vent where hot air
comes from.
Fine-tuning the image clarity
Rotate the focus ring to sharpen the image.
Auto-adjusting the image
In some cases, you may need to optimize the picture quality.
• Using the remote control
Press AUTO.
Within 3 seconds, the built-in Intelligent Auto
Adjustment function will re-adjust the values of
Frequency and Clock to provide the best picture
quality.
The current source information will be displayed
on the upper left corner of the screen for 3
seconds.
This function is only available when PC signal (analog RGB) is selected.
Operation
30
Correcting keystone
Keystoning refers to the situation where the projected image is noticeably wider at either
the top or bottom. It occurs when the projector is not perpendicular to the screen.
Correcting keystone when an image is displayed on the screen:
To correct this, besides adjusting the height of the projector, you will need to manually
correct it following these steps.
1. Press and then press to highlight
Keystone. The Keystone pop-up menu
displays.
2. Press to correct keystoning at the
bottom of the image or press to correct
keystoning at the top of the image.
Hiding the image
In order to draw the audience's full attention to the presenter, you can:
• Using the remote control
Press and hold Blank for three seconds on the
remote control to hide the screen image. Press
Blank again or any keys on the remote control to
restore the image.
• Using the projector
Press and hold Blank for 3 seconds on the projector
to hide the screen image. Press Blank again or any
keys on the projector to restore the image.
Do not block the projection lens from projecting as this
could cause the blocking object to become heated and
deformed or even cause a fire.
Press .
Press .
Operation
31
Securing the projector
Utilizing the password function
For security purposes and to help prevent unauthorized use, the projector includes an
option for setting up password security. The password can be set through the Settings
menu.
You will be inconvenienced if you activate the power-on lock functionality and subsequently
forget the password. Print out this manual (if necessary), write the password you used in this
manual and keep the manual in a safe place for later recall.
Setting power on lock
• Once a password has been set, the projector cannot be used unless the correct password is
entered every time the projector is started.
• When setting a password for the projector with its password function being used for the first
time, enter the default password (1, 1, 1, 1, 1, 1) of the projector by pressing the arrow
key six times if you are prompted for a password.
1. Press / until the Settings menu is highlighted and then press OK to enter.
2. Go to the Advanced > Security Settings > Change Security Settings menu.
3. Press OK. The message “Input Current Password” appears.
4. As pictured to the right, the four arrow keys
( , , , ) respectively represent 4 digits
(1, 2, 3, 4). Press the arrow keys to enter six
digits for the password.
5. Once the correct password is set, the OSD
menu returns to the Change Security
Settings menu.
6. Highlight Power on Lock and press OK. The
pop-up menu appears. Select On and press OK to complete power on lock setting.
7. To leave the OSD menu, press or .
If you forget the password
If the password function is activated, you will be asked
to enter the six-digit password every time you turn on
the projector. If you enter the wrong password, the
password error message displays for three seconds,
and the message “Input Password” follows. If you
enter an incorrect password 5 times in succession, the
projector will automatically shut down in a short time.
Operation
32
Entering the password recall procedure
1. Press and hold on the remote control for 3
seconds. The projector will display a coded
number on the screen.
2. Write down the number and turn off your
projector.
3. Seek help from your local BenQ service center
to decode the number. You may be required to
provide proof of purchase documentation to
verify that you are an authorized user of the projector.
Changing the password
1. Go to the Settings > Advanced > Security Settings > Change password
menu.
2. Press OK. The message “Input Current Password” appears.
3. Enter the old password.
• If the password is correct, another message “Input New Password” appears.
• If the password is incorrect, the password error message displays for three
seconds, and the message “Input Current Password” displays for you to
retry. You can press to cancel the change or try another password.
4. Enter a new password.
The digits being input will display as asterisks on-screen. Write your selected password down in
this manual in advance or right after the password is entered so that it is available to you should
you ever forget it.
Password: __ __ __ __ __ __
Keep this manual in a safe place.
5. Confirm the new password by re-entering the
new password.
6. You have successfully assigned a new password
to the projector. Remember to enter the new
password next time the projector is started.
7. To leave the OSD menu, press or .
Operation
33
Disabling the password function
To disable password protection, go to Settings > Advanced > Security Settings >
Power on Lock menu. Select Off and press OK. The message “Input Password”
appears. Enter the current password.
• If the password is correct, the OSD menu returns to the Security Settings
page with “Off” shown in the row of Power on Lock. You will not have to
enter the password next time you turn on the projector.
• If the password is incorrect, the password error message displays for three
seconds, and the message “Input Password” displays for you to retry. You can
press to cancel the change or try another password.
Though the password function is disabled, you need to keep the old password in hand should you
ever need to re-activate the password function by entering the old password.
Firmware upgrade
Follow below procedures to upgrade firmware version.
• Only an SD Card is supported for firmware update.
• Do not remove the SD Card while an update is in progress.
• Do not operate any buttons during the update.
• Do not turn the projector off during the update.
• To confirm that the firmware has been successfully updated, go to
Settings > Information
>
Firmware version.
Updating the firmware
1. Connect the SD card containing the latest firmware to the projector.
2. Select Settings > Advanced > Firmware Upgrade in the main menu page.
3. Select OK to begin.
4. After the firmware is updated, please turn off the projector.
5. Power on the projector and check the firmware version.
Operation
34
Selecting the aspect ratio
The 'aspect ratio' is the ratio of the image width to the image height. Most analog TV and
computers are in 4:3 ratio, which is the default for this projector, and digital TV and DVDs
are usually in 16:9 ratio.
With the advent of digital signal processing, digital display devices like this projector can
dynamically stretch and scale the image output to a different aspect than that of the image
input signal.
To change the projected image ratio (no matter what aspect the source is):
1. Press to open the pop-up menu in one of the computer, composite video,
component and HDMI/MHL modes.
2. Press to highlight Aspect Ratio.
3. Press / to select an aspect ratio to suit the format of the video signal and your
display requirements.
Operation
35
Optimizing the image
Selecting a picture mode
The projector is preset with several predefined picture
modes so you can choose one to suit your operating
environment and input signal picture type.
To select an operation mode that best suits your need,
you can follow the following steps.
• Make sure the input source is on computer,
composite video, component or HDMI/MHL mode
and the projection screen is being displayed.
• You may press to open the pop-up menu. Press to select Picture Mode
Settings and press OK to enter. Select Picture Mode and press / to select a
desired mode.
The picture modes are listed below.
1. Bright mode: Maximizes the brightness of the projected image. This mode is
suitable for environments where extra-high brightness is required, such as using the
projector in well lit rooms.
2. Presentation mode (Default): Is designed for presentations. The brightness is
emphasized in this mode.
3. Cinema mode: Is appropriate for playing colorful movies, video clips from digital
cameras or DVs through the PC input for best viewing in a blackened (little light)
environment.
4. Game mode: Is appropriate for playing games.
5. User mode: Recalls the settings customized based on the current available picture
modes. See "Setting the User mode" for details.
Setting the User mode
There is an user-definable mode if the current available picture modes are not suitable for
your need. You can use one of the picture modes (except the User) as a starting point and
customize the settings.
1. Press to open the pop-up menu.
2. Press to select Picture Mode Settings and press OK to enter.
3. Select Picture Mode and press / to select User.
4. Press to highlight Reference Mode.
This function is only available when User mode is selected in the Picture Mode sub-menu.
5. Press / to select a picture mode that is closest to your need.
6. Press to select a sub-menu item to be changed and adjust the value with / .
See "Fine-tuning the image quality in User mode" on page 36 for details.
7. When all settings have been done, highlight Save Settings and press OK to store
the settings.
8. The confirmation message “Setting Saved” appears.
Operation
36
Using Wall Color
In the situation where you are projecting onto a colored surface such as a painted wall
which may not be white, the Wall Color feature can help correct the projected picture’s
color to prevent possible color difference between the source and projected pictures.
To use this function, press to open the pop-up menu in one of the computer, iPhone/
iPad, composite video, component and HDMI/MHL modes. Select Wall Color and press
/ to select a color which is closest to the color of the projection surface. There are
several precalibrated colors to choose from: Light Yellow, Pink, Light Green, Blue, and
Blackboard.
Fine-tuning the image quality in User mode
According to the detected signal type, there are some user-definable functions available
when User mode is selected. Based on your needs, you can make adjustments to these
functions by highlighting them and pressing / on the projector or remote control.
Adjusting Brightness
The higher the value, the brighter the image. And the
lower the setting, the darker the image. Adjust this
control so the black areas of the image appear just as
black and that detail in the dark areas is visible.
Adjusting Contrast
The higher the value, the greater the contrast. Use this
to set the peak white level after you have previously
adjusted the Brightness setting to suit your selected
input and viewing environment.
Adjusting Color
Lower setting produces less saturated colors. If the setting is too high, colors on the image
will be overpowering, which makes the image unrealistic. Color is only adjustable under
analog video sources such as composite video and component video sources.
Adjusting Tint
The higher the value, the more reddish the picture becomes. The lower the value, the
more greenish the picture becomes. Tint is only adjustable under video and S-video
sources with video signal in NTSC or SECAM format.
Adjusting Sharpness
The higher the value, the sharper the picture becomes. The lower the value, the softer the
picture becomes. Sharpness is only adjustable under analog video sources such as
composite video and component video sources.
Selecting a Color Temperature
There are a number of options available for color temperature* settings which vary
according to the signal type selected.
*About color temperatures:
There are many different shades that are considered to be "white" for various purposes.
One of the common methods of representing white color is known as the “color
temperature”. A white color with a low color temperature appears to be reddish white. A
white color with a high color temperature appears to have more blue in it.
+50
+30
+70
0
+30
-30
Operation
37
Operating in a high altitude environment
We recommend you use the High Altitude Mode when your environment is between
1500 m –3000 m above sea level and the ambient temperature is between 0°C–30°C.
Do not use the High Altitude Mode if your altitude is between 0 m and 1499 m and ambient
temperature is between 0°C and 35°C. The projector will be over cooled if you turn the mode
on under such a condition.
To activate the High Altitude Mode:
1. Highlight Settings and press OK to enter.
2. Go to Advanced > High Altitude Mode and press OK.
3. Highlight On and press OK to confirm.
4. To leave the OSD, press until the projector returns to the home screen, or press
to go back to the home screen directly.
Operation under “High Altitude Mode” may cause a higher decibel operating noise level
because of increased fan speed necessary to improve overall system cooling and
performance.
If you use this projector under other extreme conditions excluding the above, it may
exhibit auto shut-down symptoms, which is designed to protect your projector from
overheating. In cases like this, you should switch to High Altitude Mode to solve these
symptoms. However, this is not to state that this projector can operate under any and all
harsh or extreme conditions.
Adjusting the sound
The sound adjustment functions displayed below will have an effect on the projector
speaker(s). Be sure you have made a correct connection to the projector audio input. See
"Connecting a computer" on page 17 for details on audio input connection when a
separate audio input cable is used to connect the projector.
Adjusting the sound mode
This project is preset with four sound modes to enrich your listening experience. You can
choose one of the four preset sound modes: Standard, Cinema, Music, and Game
based on your needs.
1. Highlight Settings and press OK to enter.
2. Go to Advanced > Audio Settings and press
OK to enter.
3. Highlight Sound Mode and press OK to open the
pop-up menu.
4. Highlight desired mode and press OK to confirm.
5. To leave the OSD, press until the projector
returns to the home screen, or press to go
back to the home screen directly.
Operation
39
Displaying images with PC and video source
devices
You can connect your projector to a PC and various video source devices. (e.g. HDMI,
MHL, composite video, component video) However, you need only to connect the
projector to one input source device.
To display images:
1. Connect the projector to one of the signal sources.
2. Turn on the power of the projector and your source device. The projector displays
the home screen.
3. Press / on the projector or remote control to select the input signal and then
press OK to enter.
4. Press or to go back to home screen (Does not apply when using MHL as
input source).
Certain remote control functions might not work under MHL operation because the MHL
device being used may not support these functions. Please check your MHL device for available
functions.
Operation
40
Using PC/ Video pop-up menus
The projector has a multilingual OSD that allows you to make image adjustments and
change a variety of settings. This menu is for the settings to be used in computer,
composite video, component and HDMI modes.
Using the menu
1. To open the OSD menu, press on the projector or remote control when the
projection screen is displayed.
2. When the OSD is displayed, press / to select the desired item and adjust the
settings by using / .
3. To leave the OSD, press again.
Operation
41
Menu system
Menu Item Sub-menu Options
Wall Color
Off/Light Yellow/Pink/Light
Green/Blue/Blackboard
Aspect Ratio
Auto/Real/4:3/16:9/16:10
Phase
0-31
H. Size
-6~6
Color Space
Conversion
Auto/RGB/YUV
Auto
Keystone
On/Off
Keystone
Picture Mode
Settings
Picture Mode
Bright/Presentation/Cinema/
Game/User
Reference Mode
Bright/Presentation/Cinema/
Game
Brightness
Contrast
Color
Tint
Sharpness
Color Temperature Normal/Cold/Warm
3D Sync Invert Disable/Invert
Save Settings
Information
Source
Resolution
Color System
Operation
43
Information
Source
Shows the current signal source.
Resolution
Shows the native resolution of the input signal.
Color System
Shows input system format, NTSC, PAL, SECAM, or RGB.
Operation
44
Displaying files with internal memory, USB
drive and SD card
The projector can display files saved in internal memory or external storage like an SD
card or a USB drive when you connect it to the projector.
To display files:
1. Turn on the power of the projector and the projector displays the home screen.
2. Connect the projector to one of the above external memory devices.
3. Press / to select SD card, USB Drive/Wireless Display or internal memory.
4. Storages are classified into Videos, Photos, Music, Documents menu in home
screen. Press / to select desired item and then press OK to enter different file
browser.
See "Using wireless streaming" on page 58 for details about the wireless display.
File browser window
You will only see relevant and supported files in each of file browser.
Videos Photos
Music Documents
Operation
46
2. When the OSD is displayed, press / to select the desired item and adjust the
settings by using / .
3. To exit the OSD, press on the projector or remote control again.
See the table for supported subtitle file types. Refer to "Supported file formats" on page 55.
Menu system
Menu Item Sub-menu Options
Screen
Settings
Wall Color
Off/Light Yellow/Pink/Light
Green/Blue/Blackboard
Auto Keystone On/Off
Keystone
Picture Mode
Settings
Picture Mode
Bright/Presentation/Cinema/
Game/User
Reference Mode
Bright/Presentation/Cinema/
Game
Brightness
Contrast
Color Temperature Warm/Normal/Cool
Save Settings
Play Settings
Play Mode All in folder/One video
Play Order Normal/Shuffle
Repeat On/Off
Operation
48
When playing music
Music player pop-up settings menu
The music player pop-up menu provides an on-screen display (OSD) for adjustments when
playing music.
NAME DESCRIPTION
OK/
Play/Pause Plays or pauses music.
Pause Pauses music.
Rewind Rewinds the music.
Fast-forward Fast-forwards the music.
Prev. Plays the previous music.
Next Plays the next music
/
Volume+/- Adjusts volume up/down.
Prev.
• Plays the previous music.
• Press and hold to rewind the music.
Next
• Plays the next music.
• Press and hold to fast-forward the music.
Menu Opens/closes music pop-up settings menu.
Back
• Returns to upper level of OSD.
• Closes video pop-up setting menu.
• Leaves current music player and back to music file
browser.
Home Exits music player and go back to home screen.
… 10 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für BenQ GP30 LED wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von BenQ GP30 LED

BenQ GP30 LED Bedienungsanleitung - Deutsch - 91 seiten

BenQ GP30 LED Bedienungsanleitung - Holländisch - 88 seiten

BenQ GP30 LED Bedienungsanleitung - Französisch - seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info