Bedienungsanleitung BenQ mp 622 c (Seite 32 von 63) (Englisch)

214798

Zoom out

Zoom in

Vorherige Seite

1/63

Nächste Seite

Operation32

3. To restore the picture to its original size, press AUTO. You can also press D. ZOOM -.

When the key is pressed again, the picture is further reduced until it is restored to the

original size.

• Using the OSD menu

Press Menu/exit and then press Left or Right until the Display menu is highlighted.

2. Press Down to highlight Digital Zoom.

3. Press Mode/enter and press Up to magnify the picture to a desired size.

4. Press Mode/enter to activate the Pan functionality.

5. Use the directional arrows ( , , , ) on the projector or remote control to

navigate the picture.

6. To reduce size of the picture, press Mode/enter to switch back to the zoom in/out

functionality, and press AUTO to restore the picture to its original size. You can also

press Down repeatedly until it is restored to the original size.

Selecting the aspect ratio

The 'aspect ratio' is the ratio of the image width to the image height. Most analog TV and

computers are in 4:3 ratio, which is the default for this projector, and digital TV and DVDs

are usually in 16:9 ratio.

With the advent of digital signal processing, digital display devices like this projector can

dynamically stretch and scale the image output to a different aspect than that of the image

input source.

You can change the projected image ratio (no matter what aspect the source is) by entering

DISPLAY > Aspect Ratio. Select an aspect ratio to suit the format of the video signal and

your display requirements. There are four aspect ratios available:

In the pictures below, the black portions are inactive areas and the white portions are active

areas.

1. Auto: Scales an image proportionally to fit the projector's native

resolution in its horizontal width. This is suitable for the incoming

image which is either in 4:3 nor 16:9 and you want to make most use

of the screen without altering the image's aspect ratio.

Real: The image is projected as its original resolution, and resized to

fit within the display area. For input signals with lower resolutions,

the projected image will display smaller than if resized to full screen.

You could adjust the zoom setting or move the projector towards the

screen to increase the image size if necessary. You may also need to

refocus the projector after making these adjustments.

3. 4:3: Scales an image so that it is displayed in the center of the screen

with a 4:3 aspect ratio. This is most suitable for 4:3 images like

computer monitors, standard definition TV and 4:3 aspect DVD

movies, as it displays them without aspect alteration.

4. 16:9: Scales an image so that it is displayed in the center of the screen

with a 16:9 aspect ratio. This is most suitable for images which are

already in a 16:9 aspect, like high definition TV, as it displays them

without aspect alteration.

16:9 aspect ratio is only sourced through the Component Video input when

being fed an appropriate 16:9 aspect signal. See "Connecting a Component Video source

device" on page 23 and "Obtaining a preferred projected image size" on page 17 for details.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

BenQ mp 622 c Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von BenQ mp 622 c

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info