214481
24
Zoom out
Zoom in
Vorherige Seite
1/68
Nächste Seite
Connection24
Connecting a Component Video source device
Examine your Video source device to determine if it has a set of unused Component Video
output sockets available:
If so, you can continue with this procedure.
If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to a Component Video source device
(either through a Component Video to VGA (D-Sub) adaptor
cable or Component cable):
The final connection path should be like that shown in the following diagram:
With a Component Video to VGA (D-
Sub) adaptor cable:
•With a Component Video cable:
1. Take a Component Video to VGA (D-Sub) adaptor cable or Component Video cable
and connect the end with 3 RCA type connectors to the Component Video output
sockets of the Video source device. Match the color of the plugs to the color of the
sockets; green to green, blue to blue; and red to red.
2. Connect the other end of the
Component Video to VGA (D-Sub)
adaptor cable (with a D-Sub type
connector) to the D-SUB IN socket
on the projector.
2. Connect the other end with 3 RCA
type connectors to the
COMPONENT sockets of the
projector. Match the color of the plugs
to the color of the sockets; green to
green, blue to blue, and red to red.
3. If you wish to make use of the projector (mixed mono) speaker in your
presentations, take a suitable audio cable and connect one end of the cable to the
audio output socket of the device, and the other end to the AUDIO socket of the
projector.
Once connected, the audio can be controlled by the projector On-Screen Display
(OSD) menus. See "Audio Settings" on page 53 for details.
Audio
cable
A/V device
Component Video
to VGA (D-Sub)
adaptor cable
or
Component
Video cable
The projector is only
capable of playing
mixed mono audio,
even if a stereo audio
input is connected. See
"Connecting Audio" on
page 22 for details.
If the selected video
image is not displayed
after the projector is
turned on and the
correct video source
has been selected,
check that the Video
source device is turned
on and operating
correctly. Also check
that the signal cables
have been connected
correctly.
24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für BenQ mp 730 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von BenQ mp 730

BenQ mp 730 Bedienungsanleitung - Holländisch - 69 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info