214481
27
Zoom out
Zoom in
Vorherige Seite
1/68
Nächste Seite
Operation 27
Operation
Starting up the projector
1. Plug the power cord into the projector and into a
wall socket. Turn on the wall socket switch (where
fitted). Check that the Power indicator on the
projector lights orange after power has been
applied.
2. Slide the lens cover open. If it is closed, it could
become deformed due to the heat produced by
the projection lamp.
3. Press Power on the projector or remote
control to start the projector. As soon as the lamp
lights up, a "Power On Tone" will be heard. The
Power indicator light flashes green and stays
green when the projector is on.
The start up procedure takes about 30 seconds.
In the later stage of start up, a startup logo is
projected.
(If necessary) Rotate the focus ring to adjust the
image clearness.
To turn of the ring tone, see "Turning off the
Power on/off ring tone" on page 46 for details.
If the projector is still hot from previous activity, it will
run the cooling fan for approximately 90 seconds before
energizing the lamp.
4. If you are prompted for a password, press the arrow buttons to enter a six digit
password. See "Utilizing the password function" on page 29 for details.
5. Switch all of the connected equipment on.
6. The projector will start to search for input signals. The current input source being
scanned displays in the upper left corner of the screen. If the projector doesn't detect a
valid signal, the 'No Signal' message will continue displaying until an input source
signal is found.
You can also press SOURCE on the projector or remote control to select your desired
input signal. See "Switching input signal" on page 32 for details.
If the frequency/resolution of the input signal exceeds the projector's operating range, you will
see the message 'Out of Range' displayed on a blank screen. Please change to an input signal
which is compatible with the projector's resolution or set the input signal to a lower setting.
See "Timing chart" on page 65 for details.
PUSH
I
I
27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für BenQ mp 730 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von BenQ mp 730

BenQ mp 730 Bedienungsanleitung - Holländisch - 69 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info