Bedienungsanleitung BenQ MW851UST (Seite 34 von 67) (Englisch)

468660

Zoom out

Zoom in

Vorherige Seite

1/67

Nächste Seite

Operation34

• If you press POWER to turn off the projector without disabling panel key lock, the

projector will still be in locked status the next time it is turned on.

Operating in a high altitude environment

We recommend you use the High Altitude Mode when your environment is between 1500 m

–3000 m above sea level, and ambient temperature is between 0°C–35°C.

Do not use the High Altitude Mode if your altitude is between 0 m and 1500 m and ambient

temperature is between 0°C and 35°C. The projector will be over cooled, if you turn the mode

on under such a condition.

To activate the High Altitude Mode:

1. Press MENU/EXIT and then press / until the SYSTEM SETUP: Advanced menu

is highlighted.

2. Press to highlight High Altitude Mode and press / select On. A confirmation

message displays.

3. Highlight Ye s and press MODE/ENTER.

Operation under "High Altitude Mode" may cause a higher decibel operating noise level

because of increased fan speed necessary to improve overall system cooling and

performance.

If you use this projector under other extreme conditions excluding the above, it may display

auto shut-down symptoms, which is designed to protect your projector from over-heating.

In cases like this, you should switch to High Altitude mode to solve these symptoms.

However, this is not to state that this projector can operate under any and all harsh or

extreme conditions.

Creating your own startup screen

In addition to selecting the projector preset startup screen from among BenQ logo, Black or

Blue screen, you can make your own startup screen that is a picture projected from your

computer or video source.

To create your own startup screen, project the picture you want to use as your startup screen

from either a computer or video source. The rest steps are as follows.

• Using the remote control

1. Press CAPTURE on the remote control.

2. A confirmation message displays. Press CAPTURE or MODE/ENTER again.

3. The message 'Screen Capturing...' displays while the projector is processing the

picture. Please wait.

4. If the action is successful, you see the message 'Captured Succeeded' on the screen. The

captured picture is saved as My Screen.

5. To view the captured picture displayed as the startup screen, set My Screen in the

SYSTEM SETUP: Basic > Splash Screen menu and restart the projector.

• Using the OSD menu

1. Press MENU/EXIT and then press / until the SYSTEM SETUP: Basic menu is

highlighted.

2. Press to highlight MyScreen and press MODE/ENTER.

3. Repeat steps 2-5 in the “Using the remote control” section to capture and view the

captured picture.

In the unlikely event that the capturing action fails, change your target picture. Large-sized

pictures may cause the capturing action to fail. If so, please choose a smaller one and try

again.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

BenQ MW851UST Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von BenQ MW851UST

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info