Bedienungsanleitung BenQ MX503 (Seite 24 von 55) (Englisch)

536641

Zoom out

Zoom in

Vorherige Seite

1/55

Nächste Seite

Operation24

To select the source:

1. Press SOURCE on the projector or remote

control. A source selection bar displays.

2. Press / until your desired signal is selected

and press MODE/ENTER.

Once detected, the selected source information

will display at the corner of the screen for

seconds. If there is multiple equipment

connected to the projector, repeat steps 1-2 to

search for another signal.

• The brightness level of the projected image will change accordingly when you switch between different

input signals. Data (graphic) "PC" presentations using mostly static images are generally brighter than

"Video" using mostly moving images (movies).

• The native display resolution of this projector is in a 4:3 aspect ratio. For best display picture results, you

should select and use an input signal which outputs at this resolution. Any other resolutions will be scaled

by the projector depending upon the “aspect ratio” setting, which may cause some image distortion or

loss of picture clarity. See "Selecting the aspect ratio" on page 24 for details.

Magnifying and searching for details

If you need to find the details on the projected picture, magnify the picture. Use the

direction arrow keys for navigating the picture.

• Using the remote control

1. Press Digital Zoom+/- to display the Zoom bar. Press Digital Zoom+ to magnify

the center of the picture. Press the key repeatedly until the picture size is suitable for

your need.

2. Use the directional arrows ( , , , ) on the projector or remote control to

navigate the picture.

3. To restore the picture to its original size, press AUTO. You can also press Digital

Zoom-. When the key is pressed again, the picture is further reduced until it is

restored to the original size.

• Using the OSD menu

Press MENU/EXIT and then press / until the DISPLAY menu is highlighted.

2. Press to highlight Digital Zoom and press MODE/ENTER. The Zoom bar

displays.

3. Press repeatedly to magnify the picture to a desired size.

4. To navigate the picture, press MODE/ENTER to switch to the panning mode and

press the directional arrows ( , , , ) on the projector or remote control to

navigate the picture.

5. To reduce size of the picture, press MODE/ENTER to switch back to the zoom in/

out function, and press AUTO to restore the picture to its original size. You can

also press repeatedly until it is restored to the original size.

The picture can only be navigated after it is magnified. You can further magnify the picture while searching for

details.

Selecting the aspect ratio

The “aspect ratio” is the ratio of the image width to the image height. Most analog TV and

some computers are in 4:3 ratio, and digital TV and DVDs are usually in 16:9 ratio.

Computer1/YPbPr1

Computer2/YPbPr2

Video

S-Video

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

BenQ MX503 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von BenQ MX503

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info