648938
35
Zoom out
Zoom in
Vorherige Seite
1/81
Nächste Seite
Operation 35
5. Confirm the new password by re-entering the new password.
6. You have successfully assigned a new password to the projector. Remember to
enter the new password next time the projector is started.
7. To leave the OSD menu, press Menu/Exit.
Disabling the password function
To disable password protection, go back to the SYSTEM SETUP: Advanced >
Security Settings > Change Security Settings menu after opening the OSD
menu system and press Mode/Enter. The message 'INPUT PASSWORD' displays.
Enter the current password.
If the password is correct, the OSD menu returns to the Security Settings
page. Select Power On Lock and select Off by pressing / . You will not
have to enter the password next time you turn on the projector.
If the password is incorrect, the password error message displays lasting for three
seconds, and the message 'INPUT PASSWORD' displays for your retry. You
can press Menu/Exit to cancel the change or try another password.
Though the password function is disabled, you need to keep the old
password in hand should you ever need to re-activate the password
function by entering the old password.
Switching input signal
The projector can be connected to multiple devices at the same time. However, it can
only display one full screen at a time. When starting up, the projector automatically
searches for the available signals.
Be sure the Quick Auto Search function in the SOURCE menu is On (which is
the default of this projector) if you want the projector to automatically search for the
signals.
You can also manually cycle through the available input signals.
1. Press SOURCE on the projector or
remote control. A source selection bar
displays.
2. Press / until your desired signal is
selected and press Mode/Enter.
Once detected, the selected source information
will display on the screen for seconds. If there is
multiple equipment connected to the projector,
repeat steps 1-2 to search for another signal.
The brightness level of the projected image
will change accordingly when you switch
between different input signals. Data
(graphic) "PC" presentations using mostly
35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für BenQ MX723 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von BenQ MX723

BenQ MX723 Bedienungsanleitung - Deutsch - 81 seiten

BenQ MX723 Bedienungsanleitung - Holländisch - 80 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info