214407
33
Zoom out
Zoom in
Vorherige Seite
1/36
Nächste Seite
33
Additional information
English
Replacing the lamp
The lamp may be very hot. Allow the projector to cool for at least 45 minutes before replacing the lamp.
This lamp contains mercury. Consult your local hazardous waste regulations to dispose of this lamp in a
proper manner.
10. Turn the power on and go into Setup > Lamp > Reset Lamp Timer menu to reset the lamp time.
Do not reset the lamp timer if the lamp has not been replaced as this could cause damage.
1. Turn the power off and disconnect the
projector from the wall socket. Turn off all
connected equipment and disconnect all other
cables.
2. Slightly lift the projector up. Loosen the screws on
the lamp cover (located on the left side).
3. Remove the lamp cover. 4. Loosen the screws that hold the lamp to the
projector. If the screws are not loosened
completely, they could injure your fingers. It is
strongly recommended that you use a magnetic-
head screwdriver to retain the screw should it
come loose.
5. Slowly pull the lamp out of the projector.
Pulling it too quickly may cause the lamp to
break and scatter broken glass in the projector. To
reduce the risk of injuries to fingers and damage to
internal components, use caution when removing
lamp glass that has shattered.
Do not place the lamp in locations where water
might splash on it, children can reach it, near or
above heat sources, or near flammable materials.
Do not insert your hand into the projector
when the lamp is removed. If you touch the optical
components inside, it could cause blurred images.
6. Insert the replacement lamp. Make sure it is
pushed fully and firmly in place.
7. Tighten the screws securing the lamp box.
Please be careful to not over-tighten the screws.
Loose screws may cause a bad connection, which
could result in malfunction.
8. Re-install the lamp cover.
9. Tighten the screws on the lamp cover.
PE8720-en.book Page 33 Friday, May 13, 2005 5:19 PM
33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für BenQ pe 8720 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von BenQ pe 8720

BenQ pe 8720 Bedienungsanleitung - Holländisch - 38 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info