Bedienungsanleitung BenQ PX9510 (Seite 52 von 75) (Englisch)

648906

Zoom out

Zoom in

Vorherige Seite

1/75

Nächste Seite

English

• Pack the projector in its original packing or equivalent.

Transporting the projector

It is recommended that you ship the projector with its original packing or equivalent.

Replacing the lamp

The projection lamps should be replaced when they burn out. They should only be replaced with a

certied replacement part, contact your local dealer if unsure.

• Lamps are positioned differently. Take care not to force the lamps when replacing.

• Installation of both lamp modules (Lamp 1 and Lamp 2) is required to operate the projector in dual or single lamp

mode. If only a single lamp module is installed, the projector's lamp will not turn on and will appear as a lamp failure.

• The lamp contains a certain amount of mercury and should be disposed of according to local ordinance regulations.

• Avoid touching the glass surface of the new lamp: doing so may shorten its operation life.

Lamp Handling Precautions

• This projector uses a high-pressure lamp which must be handled carefully and properly. Improper handling may

result in accidents, injury, or create a re hazard.

• Lamp life may differ from lamp to lamp and according to the environment of use. There is no guarantee of the same

life for each lamp. Some lamps may fail or terminate their life in a shorter period of time than other similar lamps.

• If the projector indicates that the lamp should be replaced, i.e., if LAMP 1 and/or LAMP 2 light up, replace the lamp

with a new one IMMEDIATELY after the projector has cooled down. (Follow carefully the instructions in the Lamp

Replacement section of this manual.) Continuous use of the lamp with LAMP 1 and/or LAMP 2 lighted may increase

the risk of lamp explosion.

• A lamp may explode as a result of vibration, shock or degradation as a result of hours of use as its lifetime draws to

an end. Risk of explosion may differ according to the environment or conditions in which the projector and lamp

are being used.

• If a lamp explodes, the following safety precautions should be taken:

• Disconnect the projector’s AC plug from the AC outlet immediately. Contact an authorized service station for a

checkup of the unit and replacement of the lamp. Additionally, check carefully to ensure that there are no broken

shards or pieces of glass around the projector or coming out from the cooling air circulation holes. Any broken

shards found should be cleaned up carefully. No one should check the inside of the projector except those who

are authorized trained technicians and who are familiar with projector service. Inappropriate attempts to service

the unit by anyone, especially those who are not appropriately trained to do so, may result in an accident or injury

caused by pieces of broken glass.

• The projection lamp should be replaced when it burns out. It should only be replaced with a certied replacement

part, which you can order from your local dealer.

• Be sure to turn off and unplug the projector at least 30 minutes before replacing the lamp. Failure to do so could

result in a severe burn.

• Safety glasses should be worn when replacing the lamp while the projector is ceiling mounted.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

BenQ PX9510 Seite 52

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von BenQ PX9510

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info