Bedienungsanleitung BenQ W1400 (Seite 27 von 63) (Englisch)

648970

Zoom out

Zoom in

Vorherige Seite

1/63

Nächste Seite

Important safety instructions

Using the preset and user modes

Selecting a preset mode

The projector is preset with several pre-defined picture modes so that you can choose one to suit your

operating environment and input source picture type.

To select a preset mode that suits your need:

1. Press MENU/EXIT and then press / until the Picture -- Basic menu is highlighted.

2. Press to highlight Preset Mode.

3. Press / until your desired mode is selected.

These modes consist of preset values suitable for various projection situations as described below:

• Cinema: With well-balanced color saturation and contrast with a low brightness level, this is most

suitable for enjoying movies in a totally dark environment (as you would find in a commercial cinema).

• Dynamic: Maximizes the brightness of the projected image. This mode is suitable for environments

where extra-high brightness is required, such as using the projector in well lit rooms.

• Standard: It is slightly brighter than Cinema mode, and suitable for use in rooms where there is a

small amount of ambient light.

• 3D: It is optimized to bring up 3D effects when watching 3D contents.

This mode is only available when 3D function is enabled.

• User 1/User 2/User 3: Recalls the customized settings. See "Setting the User 1/User 2/User 3

mode" on page 27 for details.

Fine-tuning the selected picture mode

The pre-defined picture mode settings can be altered via the available items shown in the Picture --

Basic menus.

To fine-tune the picture mode:

1. Press MENU/EXIT and then press / until the Picture -- Basic menu is highlighted.

2. Press to highlight the item you want to adjust and press / to set your desired value. Your

selection is automatically stored in the projector and associated with that input source.

See "Fine-tuning the picture quality" on page 28 and "Advanced picture quality controls" on page 30

for details.

Each time you change the picture mode, the projector also changes the setting to the one which was last

set for that particular picture mode on that particular input. If you change the input source, the most

recently used picture mode and settings for that input and resolution will be restored.

Setting the User 1/User 2/User 3 mode

There are three user-definable modes if the current available picture modes are not suitable for your

need. You can use one of the picture modes (except the selected User mode) as a starting point and

customize the settings.

1. In the Picture -- Basic menu, highlight Preset Mode and press / to select User 1, User 2, or

User 3 mode.

2. Press to highlight User Mode Management.

This function is only available when User 1, User 2, or User 3 mode is selected up in the Preset

Mode sub-menu item.

3. Press MODE/ENTER to display the User Mode Management page.

4. Press to highlight Reference Mode and press MODE/ENTER.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

BenQ W1400 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von BenQ W1400

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info