648878
44
Zoom out
Zoom in
Vorherige Seite
1/79
Nächste Seite
Menu Functions44
Switching input signal
The projector can be connected to multiple devices at the same time. However, it can only
display one full screen at a time.
If you want the projector to always automatically search for the signals:
Under the Advanced OSD menu, go to the System Setup : Basic menu, and enable
Auto Source Search. (see "Auto Source Search" on page 38)
•Under the Basic OSD menu, if there’s no signal connected to the projector, go to
Auto Source Search and enable it; if there are signals connected, go to the Settings
menu, and then enable Auto Source Search. (see "Auto Source Search" on page 38
and 39)
You can also manually cycle through the available input signals.
1. Press SOURCE on the projector or press input source
directly from the remote control. A source selection bar
displays.
2. Press / until your desired signal is selected and press
OK.
Once detected, the selected source information will
display on the screen for seconds. If there is multiple
equipment connected to the projector, repeat steps 1-2 to
search for another signal.
The brightness level of the projected image will change
accordingly when you switch between different input signals. Data (graphic) "PC"
presentations using mostly static images are generally brighter than "Video" using mostly
moving images (movies).
The native display resolution of this projector is in a 16:9 aspect ratio. For best display
picture results, you should select and use an input signal which outputs at this resolution.
Any other resolutions will be scaled by the projector depending upon the 'aspect ratio'
setting, which may cause some image distortion or loss of picture clarity. See "Aspect Ratio"
on page 52 for details.
You can also rename the source:
1. Press MENU and then press / until the System Setup: Basic menu is
highlighted.
2. Press to highlight Source Rename and press OK. The Source Rename page
displays.
3. Press /// until your desired character is selected and press OK.
44

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für BenQ W3000 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von BenQ W3000

BenQ W3000 Bedienungsanleitung - Deutsch - 79 seiten

BenQ W3000 Bedienungsanleitung - Holländisch - 79 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info