Bedienungsanleitung BenQ W700 (Seite 17 von 69) (Englisch)

468774

Zoom out

Zoom in

Vorherige Seite

1/69

Nächste Seite

Positioning your projector 17

English

How to determine the position of the projector for a

given screen size

1. Select your screen size.

2. Refer to the table and find the closest match to your screen size in the left columns

belled "16:9 screen". Using this value, look across this row to the right to find the

corresponding average distance from screen value in the column labelled "Average".

This is the projection distance.

3. On that same row, look across to the right column and make note of the "Vertical offset

in mm" value. This will determine the final vertical offset placement of the projector in

relation to the edge of the screen.

4. The recommended position for the projector is aligned perpendicular to the

rizontal center of the screen, at the distance from the screen determined in step 2

above, and offset by the value determined in step 3 above.

For example, if you are using a 120-inch screen,

the W700 average projection distance is 4325 mm and with a vertical offset of 269 mm.

the W710ST average projection distance is 2004 mm and with a vertical offset of 269 mm.

If you place the projector in a different position (to that recommended), you will have to tilt

it down or up to center the image on the screen. In these situations, some image distortion

will occur. Use the Keystone function to correct the distortion. See "Correcting keystone" on

page 33 for details.

How to determine the recommended screen size for a

given distance

This method can be used for situations where you have purchased this projector and would

like to know what screen size will fit in your room.

The maximum screen size is limited by the physical space available in your room.

1. Measure the distance between the projector and where you want to position the

creen. This is the projection distance.

2. Refer to the table and find the closest match to your measurement in the average

stance from screen column labelled "Average". If the min and max values are

available on the table, check that your measured distance is between the min and max

stances listed on either side of the average distance value.

3. Using this value, look across that row to the left to find the corresponding screen

iagonal listed in that row. That is the projected image size of the projector at that

projection distance.

4. On that same row, look across to the right column and make note of the "Vertical offset

in mm" value. This will determine the final placement of the screen in relation to the

horizontal plane of the projector.

For example,

W700: if your measured projection distance was 3.5 m (3500 mm), the closest match

in t

he "Average" column is 3604 mm. Looking across this row shows that a 

100-inch screen is required.

W710ST: if your measured projection distance was 1.5 m (1500 mm), the closest

tch in the "Average" column is 1670 mm. Looking across this row show

that a 100-inch screen is required.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

BenQ W700 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von BenQ W700

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info