Bedienungsanleitung Beper 2PASP001 (Seite 11 von 44) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

711097

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Rechargeable vacuum cleaner Use Instructions

Crevice Nozzle

Suitable for cleaning corners, cracks or areas hard to reach. To connect and disconnect it, follow the same in-

structions of the brush (FIG. F).

Instructions for use

Connect the handle to the dust tank by aligning the upper part of the handle with the upper part of the tank then

push the lower part of the handle towards the powder tank until you hear a click (FIG. B). Connect the metallic

tube (or the chosen accessory) to the dust tank until you hear a click (FIG. C). To release the metallic tube or the

accessories, push the metal tube release button.

To turn on the appliance press the switch, to turn it off press the switch again (FIG. E).

With the +/- button placed on the handle is possible to regulate the speed.

Warning: immediately turn off the product if something gets stuck inside the suction accessory.

Cleaning the appliance

Do not use water, solvents or polishes to clean the exterior of the product, only use a dry cloth.

Make sure that no liquid enters the appliance.

Do not immerse the product in water and do not clean it in dishwasher.

How to empty the dust tank

Caution: clean the dust tank and the lter after each use; the suction power will be reduced if the

tank is full and / or the lter is clogged.

To empty the dust tank push the opening button placed under the connection between the tank and the metallic

tube. To reclose it replace the lid until you hear a click.

Push the handle release button under the handle to detach it from the tank and pull away the handle from the

tank (FIG. I).

Unscrew the upper part of the tank, the motor, by turning it counterclockwise (FIG. L).

Remove the tissue lter by using the cotton tab with “UP” sign and remove the lter housing (FIG. M).

Clean the lter and the housing in water (FIG. N).

Let the lter and the housing completely dry at the air before reassemble them.

Replace the housing and the lter inside the dust tank (FIG. O), the lter’s tab must have the word “UP” facing

upwards. Screw the motor to the dust tank by turning it clockwise, until you hear a click (FIG. P).

Be sure the lter and all parts are well positioned before reconnect the dust tank to the main body.

How to clean the motorized brush

Caution: clean the brush only after detach it from the appliance.

Pull the button on the right of the brush rightward and pull it out, proceed with cleaning, let it dry and

reassemble it correctly.

Technical data

Product:

Lithium battery 22,2v, 2200 mah

Power supply:

Input: 100-240v - 50/60hz 0,5a max

Output: 26v – 0,45a

For any improvement reasons, Beper reserves the right to modify or improve the product without any

notice.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Beper 2PASP001 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info