Bedienungsanleitung Beper 40332 (Seite 9 von 40) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

710695

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

Rechargeable beard trimmer Use instructionsRechargeable beard trimmer Use instructions

Product description Fig.A

1. Cutting length selector

2. ON/OFF switch

3. Charging indicator

4. Comb attachment (1-10mm)

5. Lubricating oil bottle

6. Cleaning brush

Use instructions

Charging of the appliance

Make sure tha the appliance is switched off before charging it.

Insert the power cable in the connector found at the bottom of the appliance, and connect it to a USB plug (USB

wall adapter or PCS USB port). USB wall adapter is not included.

The charging indicator turns on, and it will stay on until the appliance is disconnected from the USB plug.

Normal charging time is 8 hours. Do not charge the appliance for a longer period of time, to avoid damaging the

battery.

8 hours of charging allow up to 60 minutes of continuous use of the appliance.

To ensure maximum life of battery, we recommend the following:

Do not charge the appliance between use sessions; allow the battery to discharge completely.

Discharge completely the batteries at least twice a year (slide the ON/OFF switch to the ON position and let the

appliance run until it stops)

Important! Do not use the appliance while charging

Avoid charging the appliance in direct sunlight or close to direct heat sources.

Use of the appliance

Make sure the appliance is switched off.

Insert the comb attachment as described below, and choose the desired cutting length with the selector.

Note: the cutting length selector does not turn while the appliance is operating.

Slide the ON/OFF switch upwards to turn the appliance on, and proceed with trimming, making sure to move

the appliance against the direction of growth of the hair, and to keep the cutting head as at as possible on the

skin. Clean the comb attachment and the blades after each use, to avoid clogging and consequent damaging

of the appliance.

Mounting/removal of comb attachment

Make sure the appliance is switched off.

To mount the comb attachment, place the cutting length selector on “10”, and x the comb attachment to the

blades as shown in (FIG. B).

To remove the comb attachment, turn the appliance off, place the cutting length selector on “10”, and gently pull

upwards.

Mounting/removal of blades

Make sure the appliance is switched off before proceeding with mounting or removal of blades.

To remove the blades, apply light pressure upwards with your thumb, right on the arrow found at the back of the

appliance (FIG.C).

To mount the blades, align the ribs on each side with the guides found on the appliance, and gently press

downwards until the blades are rmly xed (FIG.C).

Cleaning and maintenance

Make sure that the appliance is switched off, and the power cable unplugged.

Only the blades can be washed under tap water. Do not immerse

the appliance into water, and do not rinse it under tap water.

Do not use abrasive or corrosive detergents to clean the appliance

and the blades.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Beper 40332 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info