Bedienungsanleitung Beper 40742 (Seite 9 von 44) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

710690

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

5 in 1 hair and beard trimmer set Use Instructions

Description of the appliance Fig.A

1. ON/OFF switch

2. Cutting length selector

3. Hair clipper head

4. Shaver head

5. Nose/ear trimmer

6. Hair and beard trimmer

7. Precision trimmer

8. Guiding combs for hair clipper head (3 – 6 – 9 – 12 mm)

9. Guiding comb for hair and beard trimmer head

10. Standing and charging base

11. Adaptor

Charging of the appliance

This appliance can be used with or without the adaptor. It is thus possible to keep using the appliance even when

the battery runs out during operation, by simply plugging it into the wall socket.

In order to do this, make sure that the appliance is turned off before plugging it into the wall socket, and wait

approx. 1 minute before turning the appliance on again.

To charge the appliance:

a. You can connect the adaptor directly to the appliance, by inserting the connection pin in the connector found

at the bottom of hair clipper;

b. You can connect the adaptor to the standing and charging base, by inserting the connection pin inside the

hole found in the hair clipper housing, and blocking it with the cable stopper, to prevent it from detach or falling.

Once the connection pin is xed, simply place the hair clipper on the standing base, to start charging the ap-

pliance.

When the adaptor is plugged into the wall socket, the LED indicator on the display of the hair clipper turns red,

and stays on until the battery is charged.

When the LED indicator turns green, the appliance is fully charged and ready to use.

Complete charging of the appliance takes approximately 90 minutes, for 60 minutes of continuous operation

time.

Instructions for use

The appliance features 5 interchangeable heads, with different functions.

Hair clipper head

This head is used for cutting hair and beard. The 4 guiding combs included in the set allow to cut and trim hair

and beard at 4 different lengths: 3, 6, 9 and 12 mm.

Carefully brush hair and beard before starting to trim them.

Choose the guiding comb for the desired length, and insert it on to the hair clipper head, making sure that it it

well xed before switching on the appliance.

Note: make sure that the appliance is turned off and unplugged from the wall socket before inserting the

guiding comb on to the blade.

For best result, it is better to cut hair and beard following the direction of growth.

For a more precise trimming, you can remove the guiding comb from the hair clipper head, and cut your hair and

beard adjusting the height of the blades using the cutting length selector found on the hair clipper. This selector

allows to adjust blades to 3 different lengths: 0,8 mm – 1,1 mm – 1,4 mm.

Hair and beard trimmer

This head is used for trimming beard and hair. The guiding comb included in the set allows to choose 4 different

trimming lengths: 4, 5, 6 and 7 mm.

Do not leave the appliance unattended if close to places where it

could fall into water (shower, bath tub, sink, etc.). Should the ap-

pliance fall into water, do not try to pick it up; immediately unplug the

adaptor from the wall socket.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Beper 40742 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info