Bedienungsanleitung Berbel BEH 60 FLT (Seite 23 von 36) (Englisch)

784230

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Operation

6005142_0 – 24.02.2020

4.2.1 Normal operation

DWARNING

Fire hazard due to grease residue!

In operation grease residue, which is highly inflammable,

collects in and on the device.

☞Clean the device properly.

D“5. Cleaning” (page 26).

To achieve optimal efficiency in removing cooking fumes:

☞Turn the device on 1-2 minutes before you start cooking.

This allows the flow of air to build up, and the fumes are

removed at an early stage.

☞During the cooking process, switch to a power level that

is appropriate for the intensity of the cooking vapours:

yPower level 1 - lowest fan power

yPower level 2 - medium fan power

yPower level 3 - high fan power

☞If the intensity of the cooking fumes does not subside,

switch to a higher power level.

☞Switch to the Power setting when searing. After 6 minutes,

the device automatically switches back to power level 3.

To activate the Power setting permanently,

the corresponding button must be pushed again.

Then the device doesn’t switch back.

☞Check the fresh air supply at regular intervals.

☞Use the device also to reduce other unpleasant smells.

Such as from:

yOnions and garlic

yOven, microwave and steamer

yFondue and raclette

☞Turn on the run-on function when you have finished

cooking.

☞After use, turn the device off. If the automatic run-on

function is activated, the run-on time (10 minutes) starts

in power level 1.

With use of the BackFlow technology, if a power level is

active then a gentle air flow is routed from the air channel

on the underside of the device to the front air inlet. This air

circulation is necessary. The air channel on the underside of

the device must never be closed off.

After 12 hours without operation, the device (including

lighting), the device automatically shuts off.

4.2.2 Extraction mode / recirculated air mode

changeover

If the device is configured for hybrid mode, it is possible to

switch between extraction mode and recirculated air mode

at any time after activating the changeover function.

The changeover function is activated in configuration mode.

D“4.3 Configuring the device” (page 25).

Button Function

If the changeover function is activated:

☞Touch the button one time.

Button glows dimly:

yThe device operates in extraction mode.

yThe wall box is opened.

yThe cleaned air is discharged outdoors.

Button glows brightly:

yThe device is operating in recirculated air

mode.

yThe wall box is closed.

yThe cleaned air is discharged into the

room.

4.2.3 Filter filling indicator

The device has a control indicator to remind the operator

to change the filter filling. If no air circulation filter is used,

the control indicator has no meaning.

The function is set so that the button flashes every 1,000 fan

operating hours (flash duration 120 seconds) as soon as

the device is turned off. The hours counter is restarted by

switching off the control indicator.

Button Function

Button flashes:

The filter filling must be replaced.

D“6.2.2 Replace filter filling (with

recirculating or hybrid operation)”

(page 28).

☞Hold the button (> 1 second) to restart the

hours counter.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Berbel BEH 60 FLT Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Berbel BEH 60 FLT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info