Bedienungsanleitung Berbel BEH 90 FLT (Seite 24 von 36) (Englisch)

784232

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Operation

6005142_0 – 24.02.2020

4.2.4 Window contact switch

If a window contact switch is connected to the device, this

monitors whether the corresponding window is open or

closed. Extraction only takes place with an open window or

in recirculated air mode.

Button Function

Button flashes:

yA window contact switch is connected to

the device.

yThe window is closed.

yThe device does not perform extraction.

☞Open the window.

yExtraction can be used.

4.2.5 Cooktop lighting

The cooktop lighting is dimmable and is equipped with

energy-saving LEDs. The lighting can be used independently

of the fan. It can be switched on when the device is on.

It can be switched off at any time.

The colour temperature can be changed.

Button Function

Dimmer.

☞Press the button once to switch the

cooktop lighting on or off.

☞Hold the button (more than 1 second)

to start the dimmer. After releasing the

button, the cooktop lighting remains at

the selected brightness.

After switching off, the cooktop lighting

starts with full brightness the next time it is

switched on.

Colour temperature.

☞Touch the button 1x.

☞Touch and hold the button again within

half a second to start the colour cycle.

The cooktop lighting switches on, the colour

cycle starts.

☞Release the button when the desired

colour temperature is reached.

The colour cycle stops, and the selected

colour temperature is saved.

4.2.6 Run-on function

The device comes with a run-on function. When the function

is used, the device continues to work 10 minutes after being

switched off.

In recirculated air mode, it is necessary to use the run-on

function so that the device can remove the remaining odours.

Using the run-on function increases the life of the filter filling.

The filter filling must be replaced at regular intervals.

The run-on function can be switched on manually or

automatically. The device is delivered with the automatic run-

on function active, and settings are made in configuration

mode.

D“4.3 Configuring the device” (page 25).

Button Function

The device is switched on.

If the automatic run-on function is activated:

☞Touch the button one time.

yThe device switches off.

yThe run-on time (10 minutes) starts

automatically in power level 1.

yThe button for power level 1 goes on.

yThe run-on function button flashes.

yIt is possible to switch between the power

levels.

If the button is touched again, the device

shuts off completely.

The device is switched on, and any power

level is selected.

☞Touch the button one time.

yThe run-on time (10 minutes) starts in the

selected power level.

yThe button for the active power level lights

up.

yThe run-on function button flashes.

yIt is possible to switch between the power

levels.

If the button is touched again, the run-on

function stops.

4.2.7 AutoRun

Devices equipped with the AutoRun module start automatically

when the cooktop is turned on. When the cooktop is turned

off, the device switches to run-on function and then switches

off.

The AutoRun automation is set in configuration mode.

D“4.3 Configuring the device” (page 25).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Berbel BEH 90 FLT Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Berbel BEH 90 FLT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info