Bedienungsanleitung Berbel BKA 90 DLI (Seite 22 von 44) (Englisch)

784243

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Installation

6006382_a – 17.05.2022

3.5.9 Establish electrical power supply

DWARNING!

Risk of death due to electric shock!

Touching live parts can cause an electric shock, burns or

death.

☞Make sure that the following work is only carried out by

qualified electricians.

☞Ensure that the voltage supply is and remains

disconnected while the following work is in progress.

DATTENTION!

Danger of property damage due to incorrect connection!

If the hob is connected with further devices (e.g. oven),

damage can arise due to overvoltage. The customer must

provide a separate connection point with dedicated fuse for

the hob.

☞Make sure that the device is connected separately.

☞Make sure the connection is separately protected with a

circuit breaker and a residual current device.

☞Observe the voltage specifications on the ratings plate.

☞Connect the hob to the on-site power supply. The junction

box is located on the underside of the device.

Connection to spring-loaded terminals (e.g. in cooker

connection boxes) is not permitted.

3-phase connection of the hob:

L1 black Phase for left cooking zones

L2 grey Phase for right cooking zones

L3 brown Phase for fan

N blue Neutral conductor

PE green/yellow Earth

Cable H 05 VV - F, H 05 RR - F,

Diameter 5 x 2.5 mm2

Fuse 16 A

For a 2-phase connection (fuse 20 A), L2 and L3 must be

bridged.

For a 1-phase connection (fuse 40 A), L1, L2 and L3 must be

bridged.

☞Route the cables so that they are not kinked, crushed or

damaged and do not come into contact with hot parts of

the device.

☞Ensure that the cable is not disturbed during replacement

of the filter filling.

☞Make sure that the device can be disconnected on all

poles from the electricity supply after installation.

Recirculating air kit DL BUR

☞Insert the cold appliance plug into the connection socket

on the recirculated air filter.

☞Plug the mains plug into the socket.

After switching on the power supply, the device is ready for

operation.

3.5.10 Check and carry out commissioning

DATTENTION!

Risk of disruptions due to moisture in the device!

If the device is moved from a cold environment into a hot

one, condensation may form inside.

☞Wait about 2-3 hours before bringing the device into

service.

☞Ensure that the device is accessible for maintenance work

at all times (e. g. with a removable rear panel or service

cover). The space must be sufficiently large to allow for

removal of the recirculated air filter.

☞Check that an all-pole isolating device (min. 3 mm contact

gap) is present.

☞Check that the mains cable and the electrical connection

cable are not kinked, crushed or damaged.

☞Ensure that the device is not operated without

recirculated air filter or without exhaust elements.

☞Ensure that the adapters of the air-carrying components

(e.g. conduit bend, shallow duct sections) are sealed with

sealing strip.

☞Ensure that air outlets are not closed or covered.

☞With recirculated air devices: Make sure that the

ventilation slots are free.

☞Make sure that the protective film is removed.

☞Check the correct functioning of the device.

D“4. Operation” (page 23).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Berbel BKA 90 DLI Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Berbel BKA 90 DLI

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info