Bedienungsanleitung Bergamont Pedelec 2016 (Seite 58 von 87) (Englisch)

779501

Zoom out

Zoom in

Vorherige Seite

1/87

Nächste Seite

114 115

MTB-PEDELEC | ORIGINAL OPERATING INSTRUCTIONS 2016 ORIGINAL OPERATING INSTRUCTIONS 2016 | MTB-PEDELEC

b ca e fd

ENGLISH

TESTS AFTER AN ACCIDENT

1. Check whether the wheels are still firmly fixed in the drop-outs and whether

the rims are still centred with respect to the frame or fork.

Spin the wheels and observe the gap either between brake pads and rim

sides or between frame and tyre. If you have rim brakes and the width of the

gap changes markedly and you have no way to true the rim where you are,

you need to open the brakes a little with the special device so that the rim

can run between the brake pads without touching them. Note that in this

case the brakes may not act as powerfully as you are used to.

No matter whether you have rim or disc brakes, have the wheels trued by

your BERGAMONT dealer immediately after you are back home.

For more information see the chapters “Brakes”, “Using quick-releases and

thru axles” and “Wheels and tyres” and the manuals of the component manu-

facturers on this BERGAMONT info CD.

2. Check that handlebars and stem are neither twisted nor bent or broken and

that they are level and aligned. Make sure the stem is firmly fixed on the fork

by trying to turn the handlebars relative to the front wheel (e). Briefly lean on

the brake levers (f) to make sure the handlebars are firmly fixed in the stem.

REMOUNTING THE WHEEL

Mounting the wheel is done in the reverse order of dismounting. Make sure the

wheel is correctly seated in the drop-outs (a) and accurately centred between

the fork legs or the seat and chain stays. Make sure that the quick-release or the

thru axle is correctly seated (b). For more information see the chapter “Using

quick-releases and thru axles”.

If you have V-brakes and cantilever brakes hook up the brake cable at the

brake arm. To do this, grip the rim with one hand and press the brake pads and/

or the brake arms together. In this position the usually barrel shaped nipple or

the outer cable can easily be engaged (c).

If you have disc brakes, check before mounting the wheel whether the brake

pads rest snugly in their seats in the brake calliper body. The gaps between the

brake pads and the wheel should be parallel (d) and the wear indicators in their

correct position. Make sure you guide the rotor carefully between the brake

pads.

All brakes:

After mounting the wheel and tightening the quick-release pull the brake lever

(several times, if you have disc brakes).

Lift your BERGAMONT bike off the ground and spin the wheel with your hand.

With the wheel spinning the rotor should not drag along the brake calliper or

the brake pads and the rim should keep off the (rim) brake pads.

DANGER!

If you have rim brakes, make sure you hook up the brake cable immediately

after the wheel mounting!

DANGER!

Before setting off again check that the brake surfaces and/or rotors are still

free of grease or other lubricants after the wheel mounting.

DANGER!

Check whether the brake pads hit the rotors or brake surfaces of the rims.

Make sure the wheel is properly seated and ﬁrmly ﬁxed in the drop-outs.

Always do a brake test as described in the chapter “Tests before every ride”!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bergamont Pedelec 2016 Seite 58

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info