453301
19
Zoom out
Zoom in
Vorherige Seite
1/52
Nächste Seite
18
Preparation - Sewing
Thread Tension
The Basic Setting
is indicated when the red line on the tension adjustment wheel is in line with
the marking A
the tension does not need adjusting for normal sewing work
for special sewing work, the tension can be adjusted to suit the fabric
Perfect Stitch Formation
the interlooping of the threads is in the fabric
Upper thread tension too tight
the lower thread is pulled more up, i.e. to the right side of the fabric
to reduce the upper thread tension turn tension adjustment wheel to 3-1
Upper thread tension too loose
the upper thread is pulled more down, i.e. to the wrong side of the fabric
to increase the upper thread tension turn tension adjustment wheel to 5-10
Optimal upper thread tension is set in the factory. For this, Metrosene
threads 100/2 weight (Mettler, Switzerland) are used in the bobbin and
also in the upper thread.
The tension may vary when using other types of thread such as embroidery
thread, and it may therefore be necessary to adjust the tension to suit the fabric
and stitch type.
For example:
Tension Needle
Metallic thread approx. 3 90
Monofilament approx. 2-4 80
Stitch Plate
Stitch Plate Markings
the stitch plate is marked with vertical, horizontal and diagonal lines in mm
and inches
the lines help to guide the fabric for sewing seams and precise topstitching,
etc.
the horizontal markings are helpful for sewing corners and buttonholes, etc.
the diagonal markings are useful for quilting
the vertical measurements correspond to the distance between the needle
and the line
needle insertion point is position 0 (center needle position)
the measurements are marked to the right and left, measuring from the
center needle position
Removing the Stitch Plate
raise the presser foot and needle
power switch to «0» (off)
press the stitch plate down at the right back corner B until it flips up
remove the stitch plate
Replacing the Stitch Plate
place the stitch plate over the opening A and press down until it clicks into
place
A
B
A
033301.71.04_2014-02_Manual_B330_B350_PE_B380_EN
19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Bernina 330 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Bernina 330

Bernina 330 Bedienungsanleitung - Deutsch - 53 seiten

Bernina 330 Bedienungsanleitung - Holländisch - 50 seiten

Bernina 330 Bedienungsanleitung - Französisch - 52 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info