453295
132
Zoom out
Zoom in
Vorherige Seite
1/138
Nächste Seite
1
When using an electrical machine, basic safety
precautions should always be followed, including the
following.
Read all instructions before using this sewing machine.
When the machine is not in use, it should be disconnected
from the electricity supply by removing the plug from the
outlet.
DANGER
To reduce the risk of electric shock:
1. A machine should never be left unattended when
plugged in.
2. Always unplug this machine from the electric outlet
immediately after using and before cleaning.
WARNING
To reduce the risk of burns, fire, electric shock or injury to
persons:
1. Do not allow to be used as a toy. Close attention
is necessary when this machine is used by or near
children and infirm persons.
2. Use machine only for its intended use as described
in this manual. Use only attachments recommended
by the manufacturer as contained in this manual.
3. Never operate this machine if
· it has a damaged cord or plug
· it is not working properly
· it has been dropped or damaged
· it has fallen into water
Return the machine to the nearest authorized
BERNINA dealer or service center for examination,
repair, electrical or mechanical adjustment.
4. Never operate the machine with any air openings
blocked. Keep ventilation openings of the sewing
machine and foot control free from accumulation
of lint, dust and loose cloth.
5. Keep fingers away from all moving parts. Special care
is required around the sewing needle.
6. Always use the BERNINA original stitch plate. The
wrong plate can cause the needle to break.
7. Do not use bent needles.
8. Do not pull or push fabric while stitching. It may
deflect the needle, causing it to break.
9. Turn power switch to “0” when making any adjust-
ments in the needle area, such as threading or
changing the needle, threading the bobbin or
changing the presser foot.
10. Always unplug the sewing machine from the electri-
cal outlet when removing covers, lubricating or when
making any other user servicing adjustments men-
tioned in this instruction manual.
11. Never drop or insert any object into any opening.
12. Do not use outdoors.
13. Do not operate where aerosol (spray) products are
being used or where oxygen is being administered.
14. Before disconnecting, turn all controls to the off(“0”)
position then remove the plug from the outlet.
15. Do not unplug by pulling on the cord but grasp the
plug before pulling.
16. No responsibility will be taken for any possible
damage as the result of misuse of the machine.
17. This machine is provided with double insulation.
Use only identical replacement parts. See instructions
for Servicing of double-insulated machines.
SERVICING DOUBLE-
INSULATED PRODUCTS
In a double-insulated product, two systems of insulation
are provided instead of grounding. No grounding means
is provided on a double-insulated product nor should a
means for grounding be added to the product. Servicing
a double-insulated product requires extreme care and
knowledge of the system and should only be done by
qualified service personnel. Replacement parts for a
double-insulated product must be identical to those
parts in the product. A double insulated product is mar-
ked with the words “DOUBLE INSULATION” or “DOUBLE
INSULATED”.
The symbol may also be marked on the product.
SAVE THESE
INSTRUCTIONS!
This sewing machine is intended for household use only.
Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS
185_BA_engl 16.4.2004 11:30 Uhr Seite 1
030866.51.04_0401_a185_EN
2
Choosing a BERNINA “Sewing and Embroidery System” is a decision which
will have a positive impact on your sewing for years to come.
Customer satisfaction has been the driving force of our family company for over
100 years and I intend to continue that tradition of delivering superb Swiss
quality, future-orientated sewing technology and unrivaled customer service.
The new BERNINA family of creative sewing machines gives you the unique
opportunity to select what you need to satisfy your sewing needs and
requirements.
As the name suggests, the “artista” range of computer sewing is pure artistry.
These machines provide unlimited scope for total sewing pleasure. They inspire
creativity and allow you to translate your ideas into practical sewing of the finest
quality.
In addition, a wide range of sewing accessories, together with sewing publications
full of practical and creative ideas, add to the joy of sewing the BERNINA way.
It gives me great pleasure to welcome you into the BERNINA family.
www.bernina.com
Fritz Gegauf Ltd · BERNINA Sewing Machines · CH-8266 Steckborn/Switzerland
“Welcome to
the BERNINA
family!”
H.P. Ueltschi
BERNINA Sewing Machine
Company
185_BA_engl 16.4.2004 11:30 Uhr Seite 2
030866.51.04_0401_a185_EN
Contents 3
Safety Instructions
Forward
Details of the machine
Setting up the machine
Stitch Summary
Presser feet
Practical stitches/buttonholes
General instructions
Functions
Messages
Buttonholes
Alphabets/numbers
Memory
Quilt stitches/16-directional sewing/4-directional sewing
Sideways motion stitches – “Outline Designs”
Balance
Help
TTC (Thread tension/Tutorial/Creative Consultant)
smart function
Setup program
eco (ecological) function
Special accessories
Needles, Thread, Fabric Feed
Cleaning and maintenance
Troubleshooting
Glossary of terms
Index
1
2
4–5
6–13
14–16
17
18–19
20–25
25–31
31
32–39
40–41
42–47
48–50
50–51
52–53
54
55–57
58
59–72
73
73–75
76–78
79
80
81–82
83–84
185_BA_engl 16.4.2004 11:30 Uhr Seite 3
030866.51.04_0401_a185_EN
Details of the machine4
Details of the machine
Back view
Front view
1
2
3
4
5
6
7
8
11
12
14
15
16
18
19
20
22
21
24
26
27
28
29
30
23
25
17
31
35
32
9
10
13
33
34
37
38
39
50
36
49
185_BA_engl 16.4.2004 11:30 Uhr Seite 4
030866.51.04_0401_a185_EN
5Details of the machine
Bobbin cover
Stitch plate
Attachment base for special accessories
Darning ring connection
Presser foot
Needle clamp
Thread guide
Needle threader
Thread take-up cover
Thread path
Thread take-up
Bobbin pre-tension
Quick reverse button
F (Favorite Function) button
Automatic thread cutter
Screen
Bobbin winder with on/off switch and
thread cutter
Practical stitch button
Buttonhole button
Decorative stitch button
Alphabet button
External embroidery button
Quilt stitches/Directional sewing button
clr (Clear) button
mem (Memory) button
Needle stop up/down
“?” (Help) button
TTC (Thread Tension/Tutorial/ Creative
Consultant) button
Stitch width knob
Stitch length knob
Needle position
smart button
setup button
eco (Ecology) button
Free Hand System connection
Presser foot lifter (manual)
Carrying handle
Spool pins
Sewing table socket
Thread cutter
Presser foot pressure dial
Handwheel
Power switch on/off
Power plug socket
Drop feed-dog
Foot control socket
Embroidery module (special accessory)
connection
PC serial port
Lens holder
CFL-Sewing light
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
View from the left side
View from the right side
42
48
47
43
45
46
44
41
36
40
49
185_BA_engl 16.4.2004 11:30 Uhr Seite 5
030866.51.04_0401_a185_EN
Setting up the machine6
Carrying case
·protects from dust and dirt
· compartment for accessories
Accessories
· foot control
·instruction manual
· power cable
· warranty card
· FHS presser foot lifter (Free Hand System)
· seam guide for sewing table
· sewing table (attached)
· to remove the sewing table, lift slightly and remove.
To remove the case
· grasp both sides
· pull up vertically
Carrying case
Accessory box
A
Standard Accessories
(can vary from country to country)
· four bobbins
(+ one in bobbin case)
· selection of 130/705 H needles
· seam ripper
· small screwdriver
· angular Torx key
· lint brush
· seam guide
· foam pad
· Reverse pattern foot No. 1C
· Overlock foot No. 2A
· Buttonhole foot with code No. 3C
· Automatic buttonhole foot No. 3A
· Zipper foot No. 4
· Blind stitch foot No. 5
· Jeans foot No. 8
· Button sew-on foot No. 18
· Open embroidery foot No. 20C
· Sideways motion foot No. 40C
· Compensation plate for sewing buttonholes
· height compensating tool
· vertical spool holder pin
· three spool discs
· oiler
·artista data transfer CD-Rom
· CPS Installations CD-Rom
Important:
(USA/Canada only!) Use only foot
controller type LV1/LV2 with sewing machine
models 185.
Storing Accessories
· set up the free standing accessory box by pulling both extensions out
until they click into place
The accessory box is equipped with one small and one large drawer
each as well as two compartments for bobbins, two compartments for
coded presser feet and one compartment for non-coded presser feet.
The compartments can be stored in the box (additional
compartments and drawers are available as optional extras).
· insert the bobbins into the compartments provided
· to remove a bobbin, press the compartment holder A lightly
· hang presser feet in the compartments provided
· store the remaining accessories as shown in the picture
Suitcase System (special accessory)
The suitcase system is specially built for your sewing and embroidery
computer and has integrated wheels. This allows your system to be
transported easily and elegantly.
185_BA_engl 16.4.2004 11:30 Uhr Seite 6
030866.51.04_0401_a185_EN
7Setting up the machine
Larger sewing surface
· the sewing table
increases the sewing
surface
·free arm for larger
tubular items such as
pant legs and waistbands
Power cable
· the power cable is stored in the case
· plug A into machine
· plug B into electrical outlet
Foot control cable
· plug C into machine
Sewing speed
· control the sewing speed
by depressing the foot
control with your toe
· raise or lower the needle
by tapping on the foot
control with your heel
Use only foot controller
type LV1/LV2 for sewing
machine model 185
(USA/Canada only)
Raising and lowering the
presser foot
· the freehand system
raises and lowers the
presser foot
· push to the right with
your knee
· the presser foot is raised
and the feed-dogs are
lowered and the needle
thread tension is released
simultaneously
· the feed-dogs come up
Sewing table
Power cable
Foot control
Cable tidy
· wind the cable round the
spool
· insert the plug into A
When sewing
· unwind the cable to the
desired length and slip
into B or C
Power switch
Power switch
The power switch is on the
handwheel side of the machine
1 the machine is switched on
0 the machine is switched off
The sewing light is switched on
and off within the Setup
program.
Refer to the safety
instructions!
FHS (Free Hand System) presser foot lifter
automatically as soon as
the first stitch is sewn
Attaching the presser foot
lifter
· the freehand system is
stored in the case.
· insert the freehand
system into the opening
in the base plate
· you should be able to
operate the lifter in your
normal sitting position.
Note:
Your dealer can adjust the
position if necessary
A
B
C
To attach
· push over the free arm
and press firmly so that it
engages on the fixing lug
(needle and presser foot
fully raised)
To remove
· pull to the left
·remove by pulling it
completely from the
free arm
Seam guide
· insert into the groove
(underside of table) from
the right
· it can be freely adjusted
over the whole width of
the table
Scale
· number “0” corresponds
to the center needle
position
A
B
C
Important! (USA/Canada only)
This sewing machine has a polarized plug
(one blade wider than the other). To
reduce the risk of electric shock, this plug
is intended to fit only one way into a
polarized outlet. If the plug does not fit
fully in the outlet, reverse the plug. If it
still does not fit, contact a qualified
electrician to install the proper outlet. Do
not modify the plug in any way.
185_BA_engl 16.4.2004 11:30 Uhr Seite 7
030866.51.04_0401_a185_EN
Setting up the machine8
To remove
· raise the needle
· turn power switch to “0”
· open the bobbin cover
· grasp the latch of the
bobbin case
·remove case
Bobbin case
To insert
· hold the bobbin case
latch
· the opening on the case
should be at the top
· insert so that it engages
· close the bobbin cover
Bobbin thread cutter
· insert the bobbin case
· take thread over cutter (A)
· cut thread
Note:
For normal sewing, the
bobbin thread does not
have to be brought up as
the loose end is just the
right length to start sewing.
Inserting the bobbin
The bobbin must turn
clockwise when the thread
is pulled.
Insert the bobbin so that
the thread runs clockwise.
Pull the thread counter-
clockwise into the slot.
Pull the thread to the left
under the spring until it
lies in the T-shaped slit at
the end of the spring.
Winding the bobbin
Winding the bobbin
· turn power switch on
· place empty bobbin on
spindle
Thread cutter
· cut the thread on the
thread cutter
Threading the bobbin
· following the direction of the arrow take thread through
the rear guide and round the pre-tension stud
· wrap the thread around the inner bobbin two or
three times and cut off any excess thread on the thread
cutter
·press the engaging lever against the bobbin
·press the foot control
the motor stops automatically when the bobbin is full
·remove the bobbin
A
Warning:
If your sewing computer is
equipped with an embroidery
bobbin case, thread the bob-
bin thread in the guide spring
only when the embroidery
module (optional accessory)
is in use.
Refer to the safety
instructions!
185_BA_engl 16.4.2004 11:30 Uhr Seite 8
030866.51.04_0401_a185_EN
9Setting up the machine
Changing the presser foot
· raise the needle and
presser foot
· turn power switch to 0
Attaching the presser foot
· guide the foot upwards
over the cone
·press the clamping lever
down
Raising the lever
· raise the clamping lever
·remove the presser foot
Removing the needle
· raise the needle
· turn power switch to “0”
· lower the presser foot
· loosen the needle clamp
· pull the needle down to remove
Inserting the needle
· loosen the needle clamp, if needed
· flat side of needle to the back
· insert the needle as far as it will go
· tighten the needle clamp
Changing the needle
Changing the presser foot
Refer to the safety
instructions!
Refer to the safety
instructions!
Vertical Spool Pin
Vertical spool pin
· the supplementary spool pin (vertical) is stored in the
accessory box
· insert the pin from right to left in the opening
· to remove, pull to the right at the base of the spool pin
· essential sewing aid when using more than one thread,
i.e. double needle, etc. or for stacked thread spools
185_BA_engl 16.4.2004 11:30 Uhr Seite 9
030866.51.04_0401_a185_EN
Setting up the machine10
Attaching the thread spool
· raise the needle and presser foot
· turn the power switch to «0» (off)
· attach the foam pad
· place spool on pin (spool turns clockwise)
· attach the appropriate spool disc - diameter of spool
disc is disc size. There must be no clearance between
the disc and the spool
· take thread through rear guide A
· then into slit of upper thread tension
Down
· pull thread down to the right of the take-up cover to B
Up
· take thread up to the left of the cover to C in the
direction of the arrow, placing it in the take-up lever
Down
· take thread down and through guides D and E
Refer to the safety instructions!
Threading the upper thread
Needle Threader
B
A
Thread in hook
· lower the presser foot
· lay the thread behind
hook B and hold lightly
Lever down
·press lever A down and
simultaneously guide the
thread around hook B to
the right to the needle
Thread in front of needle
· put the thread from the
front into the guide until
it catches in the hook
Release the lever and
thread
· let go of lever A and
thread
Bringing up the lower thread
Bringing up the lower thread
· if bobbin thread is cut on the cutter
(page 8), there is no need to bring it up
· hold the upper thread
· sew one stitch
· pull the upper thread to bring the lower
thread up through the stitch plate hole
· take both threads through the slit on the
presser foot to the back
· pull threads over the cutter
Note:
The bobbin thread must be brought up
through the stitch plate for certain types
of work. The length of thread is sufficient
for most normal work if the lower thread
cutter has been used.
A
C
D
E
B
185_BA_engl 16.4.2004 11:30 Uhr Seite 10
030866.51.04_0401_a185_EN
11Setting up the machine
Threading the double needle
Threading the first thread
· place thread spool on horizontal spool pin
· thread by guiding the thread to the front in the slit and past
the tension disc A on the right side
· thread sewing computer as usual, but at thread guide B
guide the thread through on the right side and thread the
right needle
Threading the second thread
· place thread spool on the vertical spool pin
· thread by guiding the thread to the front in the slit and past
the tension disc A on the left side
· guide thread on the left side of the thread guide B and
thread the left needle
· threads must not be twisted together
Note:
When using the supplementary spool pin (vertical) always
attach the foam pad (prevents the thread from getting
caught on the spool pin)
Threading the triple needle
· two thread spools and one full bobbin are needed
· place one thread spool on horizontal spool pin
· place second thread spool and the lower thread spool, sepa-
rated by a spool disc, on additional spool pin (both spools
have to turn in the same direction)
· thread as usual by guiding two threads on the left side of
the tension disc A and the thread guide B and one thread on
the right side of disc
Multiple spool holder (Optional accessory)
Note:
Use of the Supplementary thread
guide (special accessories), helps
threads on the Vertical spool pin to
wind off better without failing and
slipping down the spool.
A
A
B
185_BA_engl 16.4.2004 11:30 Uhr Seite 11
030866.51.04_0401_a185_EN
12
Thread cutter
Thread cutter on head frame
· pull both threads from front to back over
the cutter.
·the threads release as soon as the first
stitch is sewn
Stitch Plate
A
A
A
9 mm Stitch plate 5,5 mm Stitch plate
(special accessory)
Straight stitch plate
(special accessory)
Stitch plate markings
· the stitch plate is marked with
vertical lines in millimeters and
inches
· mm measurements are at the
front
· inch measurements are at the
back
· the measurements correspond to
the distance from the needle to
the line
· needle insertion point is position 0
(center needle position)
· the mm/inch measurements are
marked to the right and left
· the lines help to guide the fabric for
sewing seams and for top stitching
· the horizontal markings are helpful
for sewing corners and buttonholes,
etc.
Removing the stitch plate
· turn power switch off («0»)
· raise the presser foot and needle
·press the stitch plate down at the
back right corner until it flips up
Replacing the stitch plate
· place the stitch plate over the open-
ing A and press down until it clicks
into place
Feed-dog
Button under the handwheel
Button flush with base plate = feed dogs
up, sewing position
· for all machine-fed sewing
Button depressed = feed dogs lowered,
darning position
· for free-hand sewing (darning, free-
hand embroidery, freehand quilting)
· for embroidery with the Embroidery
Module
Setting up the machine
185_BA_engl 16.4.2004 11:30 Uhr Seite 12
030866.51.04_0401_a185_EN
13
Presser foot pressure
Standard pressure
· for all normal sewing
Reduced pressure
· for jerseys and loose
knits, quilting
·prevents fabric stretching
· adjust pressure so that
the fabric still feeds
correctly
Increased pressure
· for sheer, slippery
lightweight fabrics,
quilting
· improves fabric feed and
prevents puckering
Dial on head frame
· the presser foot pressure
dial is on the left of the
head frame
Setting up the machine
185_BA_engl 16.4.2004 11:30 Uhr Seite 13
030866.51.04_0401_a185_EN
14 Stitch Summary
Practical stitches Buttonholes
9 mm/40 mm decorative stitches
185_BA_engl 16.4.2004 11:30 Uhr Seite 14
030866.51.04_0401_a185_EN
15Stitch Summary
16-directional sewing 4-directional sewing
Alphabets
Quilt stitches
185_BA_engl 16.4.2004 11:30 Uhr Seite 15
030866.51.04_0401_a185_EN
16 Stitch Summary
185_BA_engl 16.4.2004 11:30 Uhr Seite 16
030866.51.04_0401_a185_EN
17Presser feet
Presser Feet
3A
Automatic Buttonhole Foot
Buttonholes in flat
materials
Darning program
4
Zipper foot
Sewing in zippers
5
Blind stitch foot
Blind hems
Edge stitching
20C
Open Embroidery foot
Embroidery, applique,
satin stitch seams, mono-
grams
40C
Sideways motion foot
with code
For all sideways motion
stitches
4
5
2A
2A
Overlock Foot
Overlock seams,
oversewing seam edges
Note: The letter “C” after a foot number indicates the
foot is coded or equipped with a sensor for 9mm
stitching. When a stitch is selected with a coded foot
attached to the machine, the preprogrammed width is
9 mm, rather than 5.5 mm. This letter does not always
appear on the foot and in some cases does not appear
on the screen in the presser foot indicator.
1C
Reverse Pattern Foot
Practical and decorative
stitches
3C
Buttonhole Foot
Buttonholes
BERNINA Specialty Presser Feet
The standard selection of presser feet covers most normal sewing requirements but we recommend the use of BERNINA
specialty presser feet for specific sewing tasks such as quilting, heirloom sewing, home decorating, tailoring, etc.
They are available from your BERNINA dealer.
3A
8
8
Jeans foot
Straight stitching in thick,
firm fabrics
18
18
Button sew-on foot
Sewing on buttons, hooks
and eyes
185_BA_engl 16.4.2004 11:30 Uhr Seite 17
030866.51.04_0401_a185_EN
18 Practical stitches
Practical stitches
1 Straight stitch
All non-stretch fabrics. All straight
stitch work.
2 Zig-zag
Most fabric types. All simple zig-zag
applications such as oversewing fine
fabrics, attaching elastic, lace and
appliqué.
3Vari-overlock
Primarily for fine jerseys, stretch
overlock seams and hems.
4 Running stitch
Most types of fabric. Mending,
patching, reinforcing seams.
5 Securing stitch
All types of fabric. Secures the
beginning and end of seams sewn
with straight stitch.
6Triple straight stitch
Reinforced seams in tough, heavy
fabrics.
7Triple zig-zag
Reinforced seams in firm fabrics, visible
hems and seams, decorative stitching,
couching.
8 Honeycomb stitch
Most types of interlock and smooth
fabrics. Visible seams and hems.
9 Blindstitch
Most types of fabric. Blind hems, shell
edging on soft jerseys and fine fabrics,
decorative seams.
10 Double overlock
All types of knit. Sews and finishes the
edges in one operation.
11 Super stretch
Open seam in all super-stretch fabrics,
such as Lycra.
12 Gathering stitch
Most types of fabric. Gathering with
shirring elastic. Butted seams (edge to
edge).
13 Stretch overlock
Medium weight knits, toweling and
firm wovens. Overlock seams, flat
joining seams.
14 Jersey stitch
Natural, blended or synthetic fabrics
and delicate knits. Visible seams and
hems. Mending jersey/interlock.
15 Universal stitch
Firm fabrics such as felt and leather.
Flat joining seams, visible seams,
attaching elastic, decorative seams.
16 Sewn-out zig-zag
Oversewing woven fabrics, reinforcing
edges, attaching elastic, decorative
seaming.
17 Lycra stitch
All two-way stretch fabrics, flat joining
seams and hems, reinforced seaming
on underwear.
18 Stretch stitch
All stretch fabrics, open seam in
sportswear.
19 Reinforced overlock
Medium to heavy weight knits and
toweling, overlock seams, flat joining
seams.
20 Knit overlock
All knits, machine or handmade. Sews
and finishes edges in one operation.
185_BA_engl 16.4.2004 11:30 Uhr Seite 18
030866.51.04_0401_a185_EN
19Practical stitches
21 Basting
Basting seams, hems, etc.
22 Simple darning program
Automatic darning in fine and medium
weight fabrics.
23 Reinforced darning program
Automatic darning in heavy weight
fabrics.
24 Bar tack program
Reinforcing pocket edges, belt loops
etc.
25 Bar tack program
Reinforcing pocket edges, belt loops
etc.
26 Fly stitch large
Medium- to heavyweight fabrics, rein-
forcing pocket edges, zippers and
openings
For specific instructions on using various
practical stitches, refer to the artista 185
Sewing Manual, pages 2–20.
Buttonholes
51 Standard buttonhole
Fine to medium weight fabrics.
Blouses, shirts, trousers, bedding, etc.
52 Narrow buttonhole (heirloom sewing)
Fine to medium weight fabrics.
Blouses, shirts, dresses, trousers,
children’s and baby clothes, dolls’
clothes and heirloom.
53 Stretch buttonhole
All stretch fabrics made from cotton,
wool, silk, and synthetic fibers.
54 Round buttonhole with normal bartack
For medium to heavy weight fabrics of
all types. Clothing, jackets, coats,
rainwear.
55 Round buttonhole
with horizontal bartack
For medium to heavy weight fabrics of
all types. Clothes, jackets, coats, rain-
wear.
56 Keyhole buttonhole with
normal bartack
Heavy weight, non-stretch fabrics.
Jackets, coats, trousers, leisure wear.
57 Keyhole buttonhole with
pointed bartack
For non-stretch firm fabrics. Jackets,
coats, leisure wear.
58 Keyhole buttonhole with
horizontal bartack
For firm, non stretch fabrics. Jackets,
coats, leisure wear.
59 Straight stitch buttonhole
For reinforcing satin stitched
buttonholes, making bound
buttonholes, and stitching buttonholes
in leather or imitation suede.
60 Button sew-on program
For buttons with 2 and 4 holes.
61 Narrow zig-zag eyelet
Opening for cords and narrow rib-
bons/bands, decorative work.
62 Straight stitch eyelet
Opening for cords and narrow ribbons.
63 Hand-look buttonhole
Light- to mediumweight woven fabrics.
Blouses, dresses, leisure wear, bedding
For more information on stitching various
types buttonholes, refer to the artista 185
Sewing Manual, pages 21–30.
185_BA_engl 16.4.2004 11:30 Uhr Seite 19
030866.51.04_0401_a185_EN
20 General instructions
Screen
The artista is operated with a combination of external buttons and
knobs and a touch screen.
Switch machine on
· power switch to “1”
Welcome screen
· welcome
· appears for approximately 3 seconds
· can be disabled in the Setup program
Practical stitch screen
· the practical stitch screen appears
immediately after the welcome
· screen shows:
A–presser foot indicator
B–needle stop position
C–assigned Favorite Function
button
D–selected stitch and number
E–stitch width (basic setting
always visible)
F–needle position
(11 possibilities)
G– up/down scroll arrows
H–stitch length (basic setting
always visible)
I–scroll arrow for functions
J–stitch selection by number
(selected stitch is highlighted)
K–functions
A
B
CD
E
F
G
H
I
JK
185_BA_engl 16.4.2004 11:30 Uhr Seite 20
030866.51.04_0401_a185_EN
21General instructions
On-screen stitch selection/stitch display/functions
Stitch Selection
· touch the stitch of your choice
· the stitch is highlighted
· every stitch is displayed with its
number
Altering the stitch width
· turn the upper knob
· altered width is shown on the stitch
width bar
· the basic setting will still be visible
(shown at 3 mm)
· stitch width can be altered from
0 mm to 9 mm when using coded
feet
· stitch width bar automatically
shows 0–9 when using coded feet
· stitch width can be altered from
0 mm to 5.5 mm when using non-
coded feet
· stitch width bar automatically
shows 0–5 when using non-coded
feet
Altering the stitch width
· turn the upper knob
· altered length is shown on the
stitch length bar
· the basic setting will still be visible
(shown at 3 mm)
· stitch length can be altered from
0 mm to 5 mm on most stitches
Altering the stitch length
· turn the lower knob
Display of selected stitch
·a graphic of the selected stitch is
visible in the center of the upper
portion of the screen
· the stitch number is displayed to
the top left of the stitch graphic in
the center of the upper portion of
the screen
Altering the needle position
·press the right or left needle
position button
· each press moves the needle one
position to the right or left
185_BA_engl 16.4.2004 11:30 Uhr Seite 21
030866.51.04_0401_a185_EN
22 General instructions
Functions
· touch the function of your choice
· the selected function is highlighted
(a number of different functions
can be selected simultaneously)
· touch the function toolbar arrow to
scroll more functions
· activate another function if desired
· touch the toolbar arrow to scroll
again
· the toolbar can be customized in
the Setup program
· For more information on functions,
see pages 24–31
Return to basic settings
·press the external clr button
· the stitch will revert to its basic set-
tings
Presser foot indicator
· the recommended presser foot is
displayed by number
Needle stop adjustment
·press the needle stop button
·arrow points down
· the machine always stops with the
needle down
·press needle stop button again –
needle stop reverts to up (arrow
points up)
Stitch selection
Direct selection by scrolling up/down
· touch the arrow (down)
· scroll the screen to view all stitches
· the top row disappears
· the next two rows move up
·a new row appears at the bottom
· touch the arrow (up)
· the first row of stitches appears
again
· the scroll function (up/down) is
used to find and view all the
machine’s stitches
· use when a visual search for a
particular stitch is needed
· when the desired stitch is located,
touch it to select
Stitches can be selected using one of
the two methods listed below.
Select a stitch by number
· touch the function “0–9”
· the screen changes to stitch
numbers
· touch numbers to select the stitch
of your choice
· the number of the selected stitch
appears in the top row
Correct
· to correct mistakes or deselect,
touch del (top right)
· the cursor moves to the left and
deletes the number
· select new number
185_BA_engl 16.4.2004 11:30 Uhr Seite 22
030866.51.04_0401_a185_EN
23General instructions
Confirm and go to next screen
· touch OK to confirm
· the screen displays the selected
stitch
· the selected stitch is active
(highlighted)
Back to previous screen
· touch esc
· the previous screen appears
· if the selection was not confirmed
by touching OK, the stitch selected
by number will be ignored
Note
If an unavailable number is
entered, the screen will not react.
Simple menu selection
External menu buttons
·press a button to select the desired
menu
· the first stitch, stitch program, or
stitch summary appears on the
screen
Practical Stitches Buttonholes
Decorative Stitches Quilt/Directional
Stitches
Alphabets Embroidery
Practical stitch button
· the practical stitch menu appears
· the straight stitch at the top left is
active (highlighted)
· 15 practical stitches appear on the
screen
· use arrows to scroll for viewing
additional stitches
Buttonhole button
· the buttonhole menu appears,
including the eyelet and button
sew-on programs
Decorative stitch button
· the decorative stitch menu appears
· pattern types and sizes can be
selected including 9mm decorative
stitches and sideways motion
stitches (indicated with a cross
symbol)
· touch to select the desired stitch
group
· the selected stitch group appears
185_BA_engl 16.4.2004 11:30 Uhr Seite 23
030866.51.04_0401_a185_EN
24 General instructions
Alphabet button
· the alphabet menu appears
· touch to select the alphabet of
your choice
Quilt stitches/Directional sewing
button
· the menu of the 3 categories
appears:
· quilt stitches
· 16-directional sewing
· 4-directional sewing
· touch to select the category of
your choice
· the menu of all stitches in that
category appears
quilt stitches
16 directions
4 directions
Setup button
·press the external Setup button
· menu appears
· use Setup to customize your
machine’s settings
· stitches and functions can be
combined to form a customized
menu (Personal program)
· customized menu (Personal
program) can be saved
· saved customized menu (Personal
program) can be opened at any
time
· customized settings can be can-
celled at any time
External function buttons
clr (Clear)
·press the clr button
· stitch length, width, needle positi-
on, tension and balance will be
returned to basic settings
· most functions will be deleted (see
individual functions)
Smart button
·press the Smart button
· the stitch is saved with all
adjustments to width/length, need-
le position, tension and balance
· select a new stitch, e.g. button-
holes
·press the Smart button to return to
the previous screen with saved
settings
· use the Smart button to toggle
between stitches as you work
mem (Memory)
·press the mem button
· memory is open and appears on the
screen
· the memory bar replaces the third
row of stitches on the screen
·press mem button again to close
· for more information on using the
memory, see pages 42–47
Setup
·press Setup
· menu appears
· use Setup to customize your
machine’s settings
· stitches and functions can be
combined to form a customized
menu (Personal program)
· customized menu (Personal
program) can be saved
· saved customized menu (Personal
program) can be opened at any
time
· customized settings can be
cancelled at any time
185_BA_engl 16.4.2004 11:30 Uhr Seite 24
030866.51.04_0401_a185_EN
25General instructions / Functions
Needle stop
· the default setting of the needle
stop is the “up” position
·press the needle stop button
· the on-screen arrow will now point
down
· the machine will now always stop
with needle down
·press the needle stop button again
to revert to needle stop up
“?” (Help)
·press the Help button
· touch a stitch or function
·a description of the selected stitch
or function appears
TTC (Thread tension/Tutorial/Creative
Consultant)
·press the button
· three menus appear on the screen
· Thread tension
· Tutorial (brief operating
instructions)
· Creative Consultant (advice on
fabric,needle,techniques, and
thread tension)
· touch to select the desired menu
· the information selected is activat-
ed and the appropriate screen will
appear
Needle position
·press the left or right needle
position button
· the needle moves to the right or
left as selected
· total of 11 needle positions:
5 left, 5 right, and center
eco (ecology) button
·press the eco button
· energy use by the machine is cut by
50%
· particularly useful for long
interruptions in work
· all settings remain active; foot
control is inactive
· screen saver is activated
·press the eco button again to
restore the sewing machine to
normal function
Quick reverse button (above needle)
·press the quick reverse button
· secure the seam beginning and end
– sews in reverse as long as button
is depressed
· used to program buttonhole length
· used to program darning length
· used to switch to straight stitch
securing program (Stitch no. 5)
· used to start/stop stitching with the
embroidery module (special
accessory)
Automatic thread cutter
·press the external button
· the upper and bobbin thread are cut
automatically
F (Favorite function) button
(above needle)
· this button can be individually
programmed in Setup with a
function of your choice
· selected function can be cancelled
and reprogrammed at any time with
another function
· personal program can be pro-
grammed into “F” button
· for more information on the
Favorite function button, see
page 63
On-screen functions
Fields are highlighted when functions are activated.
Activated functions can be cancelled individually by
pressing a second time.
All selected functions can be cancelled simultaneously by
pressing the external clr button.
Exceptions:
Needle stop Motor speed Double needle limitation
These functions must always be cancelled individually.
185_BA_engl 16.4.2004 11:30 Uhr Seite 25
030866.51.04_0401_a185_EN
26 Functions
General functions
Scroll up
· touch one or more times
· screen scrolls up to show more
options
· touch the symbol continuously to
scroll quickly
Scroll down
· touch one or more times
· screen scrolls down to show more
options
· touch the symbol continuously to
scroll quickly
Closing special applications
· touch esc
· the special application closes
·returns to previous screen
OK
· touch to confirm and activate
adjustment/selection, e.g. thread
tension change
·programmed adjustment/selection
is ready to sew
The following functions are found on various screens and
programs of the artista sewing machine. They are
consistently used in the same manner for specific tasks
when accessing and moving between different programs.
Function toolbar
Complete function toolbar as it
appears in the practical stitch program.
Hidden functions that can be
accessed by scrolling with the arrow.
Pattern begin
· touch symbol
· the needle moves to the beginning
of a stitch or stitch combination
· field is highlighted but reverts to
normal after 2 seconds or after
beginning to sew
· if selecting Pattern begin for a
memory combination, the cursor
will appear to the right of the first
stitch on-screen
Applications:
· embroidery, buttonholes, working
in memory
Securing
· touch symbol
· individual stitches will be secured
at the beginning and end with
4 stitches
· securing in memory: stitch and
letter combinations will be secured
at the beginning and end
Applications:
· sewing individual decorative
stitches
· sewing individual letters
· sewing stitch combinations and
words
Motor speed
1
4
,
1
2
,
3
4
,
4
4
· touch symbol one or more times to
select speed
· selected speed is displayed
·reduces or increases the motor
speed
· will sew the selected maximum
speed with the foot control fully
depressed
Applications:
· adjust speed for decorative sewing
machine work such as freehand
embroidery or freehand quilting
and when more control is desired
for the sewing task
· when children are sewing
Note:
The scroll arrow and the 0–9 (stitch selection by number)
will remain on the screen for easy access and will never be
hidden. A total of eight functions (or four memory
functions) will show on-screen.
The following functions are available on the artista
sewing machines. Any function which can be used in the
selected program will appear on the screen in the bot-
tom row. If there are more than eight (or four memory
functions), the remaining ones will be hidden and can be
accessed by using the arrow in the lower right corner to
scroll. When a hidden function is active, the arrow will
flash.
Pattern end
·touch symbol
· sewing computer stops at the end of
the active single pattern or the active
pattern within a combination
185_BA_engl 16.4.2004 11:30 Uhr Seite 26
030866.51.04_0401_a185_EN
27Functions
Pattern repeat 1–9 x
· touch symbol one or more times to
select number required
·1 = machine stops at the end of an
individual stitch or stitch combina-
tion
· 2–9 = machine stops at the end of a
stitch or stitch combination after
the number of repeats selected
Applications:
· sewing individual motifs
· combine with practical stitches and
4-directional sewing
· Sews memory contents the
specified number of times
Mirror image – right/left
· touch symbol
· machine sews selected the stitch in
mirror image (right/left –
determined by the sewing direction)
· can be saved in memory
Applications:
· decorative stitching
· pattern combinations in memory
Long stitch
· touch symbol
· machine sews every second stitch
(max. stitch length 10 mm)
· can be activated for all practical,
decorative, and directional stitches
except buttonholes and sideways
motion stitches
· functions and stitches can be
combined
· can be saved in memory
· does not operate with the embroi-
dery module (special accessory)
Applications:
· combine with straight stitch to
baste
· combine with triple straight stitch
for topstitching
Mirror image – up/down
· touch symbol
· machine sews selected stitch in
mirror image (up/down –
determined by the sewing direction)
· can be saved in memory
Applications:
· decorative stitching
· pattern combinations in memory
Stitch selection by number
· touch number symbol
· select stitch by touching the
appropriate number combination
Applications:
· quick selection of individual stitches
· quick selection of sitches for
memory combinations
Scroll
· touch one or more times to view
more functions
Applications:
· view all available functions
· combine functions with stitches for
individual motifs or in memory navi-
gation through memory
Pattern extend 2–5x
· touch one or more times
· the numbers 2–5 appear depending
on the type of stitch selected
· the length of selected stitch will be
increased by 2–5 times
· lengthened stitches can be
programmed in memory
Applications:
· lengthen existing patterns without
affecting the stitch density
· Function can be combined with
stitches and saved in memory
Continuous reverse sewing
· touch symbol
· sews the selected stitch in reverse
Application:
· darning with straight or running
stitch
· decorative stitching on sleeves or
trouser legs
· quilting
Half pattern
· touch symbol
· machine automatically stops at the
halfway point of the stitch pattern
· when stitching is resumed, the
pattern is completed and the first
half of the next pattern is stitched
before the machine automatically
stops again
· use Single pattern to stop at the
end of the second half of the stitch
pattern
Application:
· turning corners
· altering decorative stitches for a
new look
185_BA_engl 16.4.2004 11:30 Uhr Seite 27
030866.51.04_0401_a185_EN
28 Functions
Double needle limitation
· touch one or more times to select
number from 2 to 8
· the numbers represent the distance
between the needles in mm
· the stitch width will be limited
automatically
· this prevents the needles from hit-
ting the presser foot or stitch plate,
avoiding needle breakage
· can be saved in memory
Applications:
· sewing pintucks
· hemming knits
· decorative stitching
Clear All
· clears all settings that were changed except those
that were changed using the Setup program
·returns to default settings
· Settings affected:
Continuous Reverse
Long Stitch
Pattern End
Securing Function
Mirror Image – up/down
Mirror Image – left/right
Pattern Extend
Balance
Stitch Length
Stitch Width
Needle Position
Half Pattern
Double Needle Limitation
Hemstitch Needle Limitation
Needle Stop Position
Motor Speed
Alphabet Size
Monogram Size
Stored Buttonholes
Tension Function
Note:
There are two additional functions,
Tension and Hemstitch Needle
Limitation, available for placement on
the function toolbar (see Functions in
Setup, page 28). These can be placed
on the toolbar using the Setup pro-
gram (see page 63).
Balance
· touch symbol to open balance screen
· correct forwards and reverse stitches
· correct sideways motion stitches
Applications:
· adapting practical and decorative
stitches to various types of
fabrics
· altering decorative stitches for a new
look
· adapting buttonholes to different
fabrics
· adapting sideways motion stitches to
different fabrics
Hemstitch (wing) needle limitation
· will not show up on the function
toolbar unless it is inserted by the
user
· can be installed in the Setup
program
· the stitch width is limited auto-
matically
· needle position is limited to center
·prevents the needle from hitting
the presser foot or stitch plate,
avoiding needle breakage
Application:
· hemstitching
· decorative stitching
Tension
· will not show up on the function toolbar unless it is
inserted by the user
· can be installed in the Setup program
· touch symbol to access tension screen
· tension changes affect the selected stitch only
· visual change of setting appears on the tension screen
· default setting shown by a fine line
·touch reset to return to basic settings (factory setting or
values selected in Setup)
Functions in Setup
Personal program
· touch symbol
· personal screen appears
Applications:
· quick method to open personal
program
The functions below are available in the Setup program
of the artista sewing machine. They are sewing functions
used from the sewing screens; however, they will not
show up on the toolbar at the lower edge of the screen
unless specifically placed there. For more information,
see pages 62–63.
185_BA_engl 16.4.2004 11:30 Uhr Seite 28
030866.51.04_0401_a185_EN
29Functions
Functions in Memory
Delete
· touch symbol
· delete individual stitches or letters
to the left of the cursor
· delete stitch combinations
Applications:
· corrections in memory
· delete complete memories
Select memory
· the opened memory bank is
displayed with its number
· touch check to display the contents
of the memory bank
· touch esc to close the memory bank
· leave memory: press external mem
button
Applications:
· working in memory
· saving stitch combinations
Store
· touch symbol
· saves individual stitches, stitch
combinations and letters
Application:
· saving programs
Check
· touch symbol
· memory contents are displayed
Application:
· check and correct memory contents
The following functions become available along the
lower portion of the screen when the external memory
button is pressed to access the memory feature.
Edit memory contents
· touch symbol
· scroll through the memory bank
and select stitch to edit
· choose from a variety of functions
to change, including, Stitch length,
Stitch width, Neddle position,
Motor speed, Long stitch, Tension,
Mirror images, Pattern Extend, and
Balance
· choose to add the Securing func-
tion within a combiantion or add a
Sub-divider to the memory bank
Application:
· correcting, changing memory
contents
Scroll left
· touch symbol once or several times
· memory contents are scrolled
backward
Scroll right
· touch symbol once or several times
· memory contents are scrolled
forward
Mirror image – right/left
· touch symbol
· machine sews selected stitch flipped
right to left
· alteration of selected stitch is
shown on-screen
Mirror image – up/down
· touch symbol
·machine sews selected stitch flipped
up/down
· alteration of selected stitch is
shown on-screen
Tension
· touch symbol to access tension
screen
· tension changes affect the selected
stitch only
· visual change of setting on tension
screen
· default setting shown by a fine line
·touch reset to return to basic
settings (factory setting or values
selected in Setup)
Securing function
· touch symbol
· can be inserted between stitches in
the memory
The following functions become available in the center
of the screen when the edit function is selected. All func-
tions on the toolbar (except del) will become inactive
when the edit function is selected and will reactivate
when the edit function is closed.
Motor speed
· touch symbol one or more times to
select speed
· selected speed is displayed
· full speed is 900 stitches per minute
(unless the basic setting has been
changed in the Setup program)
·reduces or increases the sewing
speed
1
/
4
at a time (
1
/
4
,
2
/
4
,
3
/
4
,
4
/
4
)
Functions in Editing
185_BA_engl 16.4.2004 11:30 Uhr Seite 29
030866.51.04_0401_a185_EN
30 Functions
Pattern Extend 2–5x
· touch one or more times
· the numbers 2–5 appear
depending on the type of stitch
selected
· the length of selected stitch will be
increased by 2–5 times
· the stitch density is not affected
· lengthened stitches can be
programmed in memory
Balance
· touch symbol to open balance
screen
· correct forwards and reverse
stitches
· correct sideways motion stitches
Letter size
· touch one or more times
· one half of field is highlighted
· the gray section visually indicates
the letter size: large (9 mm) or
small (6 mm)
Monogram sizes
· appears in editing in place of Letter
Size function when a monogram is
selected
· when monograms are selected,
size 1 = 30 mm is automatically
activated
· touch symbol – the middle field is
activated (2 = 20 mm)
· touch symbol again – the right
field is activated (3 = 15 mm)
Long stitch
· touch symbol
· machine sews every second stitch
(max. stitch length 10 mm)
Memory sub-divider
· touch symbol
· the memory has up to 255 sections
or banks
· each bank can be subdivided as
desired
· total memory (all banks together)
holds 1023 stitches
Buttonhole program functions
Buttonhole length – direct length
entry
· touch symbol to open number
screen
· enter button size (diameter +
thickness) in mm
Application:
· use this method if you know the
size of your button
Buttonhole length – on screen measure-
ment
· touch symbol to open measuring
screen
· hold button to bottom lower left
corner of screen and use the stitch
width knob to measure it
· buttonhole length will be
programmed with 2 mm added
automatically
Application:
· simple method to determine
buttonhole size
Manual buttonhole
· touch symbol
· follow procedure (4–6 steps,
depending on buttonhole type)
Application:
· for individual manually sewn
buttonholes
· to repair existing buttonholes
Stitch counter buttonhole
· select buttonhole
· touch symbol
· stitch counter buttonhole will be
activated
The functions below appear on the function toolbar at
the lower edge of the screen when any buttonhole
(stitches 51–63) is selected.
185_BA_engl 16.4.2004 11:30 Uhr Seite 30
030866.51.04_0401_a185_EN
31Functions/Messages
Letter size
· appears in toolbar when any letter
or character of one of four
styles of alphabets is selected
· touch one or more times
· one half of field is highlighted
· the gray section visually indicates
the letter size: large (9 mm) or
small (6 mm)
Applications:
· size selection
· size alteration is saved in memory
Monogram size
· appears in toolbar when any letter
of the monogram alphabet is
selected
· touch once or twice to select
· the number selected will be
highlighted
· monogram sizes are 1 = 30, 2 = 20,
3 = 15 mm
Application:
· size selection
One of the following functions will appear in the lower
left corner of the screen when a letter/number of an
alphabet or monogram is selected. It will reduce the
number of normal functions shown on the toolbar by
one, causing it to be hidden.
Alphabet program functions
Messages
The following messages may appear on the screen of the
artista sewing machine during certain operations.
They are reminders, warnings, or confirmations about
the function or stitch being selected. Below is a list
of the messages pertaining to the sewing machine (see
embroidery manual for messages that pertain to the
embroidery module) and the appropriate responses.
MESSAGE RESPONSE
Please check the lower thread. Check to see if the bobbin thread has run out. Wind and insert a new bobbin
if needed. Machine will not sew until this is corrected.
Please check the upper thread. Check to see if the needle thread has run out or has broken. Rethread the
needle thread if needed. Machine will not sew until this is corrected.
The bobbin winder is on. Check to see if bobbin winder is on. If the bobbin winder is on, the foot
pedal is inactive and the machine will not sew. Disengage the winder if
needed. Machine will not sew until this is corrected.
Note: This message will appear when winding a bobbin; touch esc to clear it
from the screen.
Do you really want to delete the Confirms the delete command before any stitches or functions are erased
contents of this memory? from memory. Touch OK to continue with the deletion process; touch esc to
abort the process.
Personal Program memory is full. To save a stitch, an already saved stitch must be deleted.
Memory is full. To save a stitch, an already saved stitch must be deleted.
This function will not appear in Directional stitches and motifs (4, 16 direction and alphabets) cannot be
the personal program. stored in the Personal Program. Select another stitch from any other menu.
Main Drive Failure. Remove any trapped remnants of thread from the hook race.
Please check hook system.
185_BA_engl 16.4.2004 11:30 Uhr Seite 31
030866.51.04_0401_a185_EN
32 Buttonholes
Buttonholes
Buttonholes/Button sewing on
program/eyelets
·press the external Buttonhole
button (to the right of screen)
· screen shows an overview of all
buttonhole and eyelet types
· 51 standard
· 52 narrow (heirloom)
· 53 stretch
· 54 round with normal bartack
· 55 round with horizontal bartack
· 56 keyhole with normal bartack
· 57 keyhole with pointed bartack
· 58 keyhole with horizontal bartack
· 59 straight stitch buttonhole
· 60 button sew-on program
· 61 zig-zag eyelet
· 62 straight stitch eyelet
· 63 hand-look buttonhole
Select buttonhole/button sew-on
program/eyelet
· touch symbol
· selected buttonhole, eyelet or
button sew-on program is activated
· If one of the buttonholes (51–63) is
activated, all functions are reset to
the default settings
Buttonholes are practical closures
which can also be used for a
decorative effect. The artista 185
provides a very versatile selection.
All buttonholes can be sewn and
programmed in a variety of ways.
3A
Automatic buttonholes (standard, narrow and stretch)
Both beads are sewn in the same direction.
Buttonhole length =
buttonhole opening in mm
Note: the automatic buttonhole foot No.3A must lie flat
on the fabric, i.e. not on a seam allowance, otherwise the
length will not be measured accurately.
Automatic buttonhole
· the lens on the buttonhole foot No.3A will register the
length that you determine automatically
· for making buttonholes from 4–29 mm length
For buttonhole example,
refer to the artista 185
Sewing Manual, page 25.
Buttonhole Leveler
(optional accessory)
When sewing a buttonhole using Automatic Buttonhole
Foot No. 3A on an uneven area (such as over a seam allow-
ance), use the Buttonhole Leveler. This accessory will
create a smooth surface for the foot and help make a
perfect buttonhole.
Sewing the first bead
· the sewn section will be
displayed on the screen
(to the right of the pres-
ser foot indicator)
· sew the first bead for-
wards, stop the machine
at the desired length
Programming the button-
hole
·press and release the
quick reverse button
· auto appears in button-
hole symbol = length is
programmed
· machine sews straight
stitch backwards
Auto buttonhole
· machine sews first bar-
tack automatically
· machine sews second
bead forwards
· machine sews second
bartack automatically
· machine sews securing
stitches automatically
· machine stops and
returns automatically to
the beginning of the but-
tonhole
Deleting saved
buttonholes
·press the external «clr»-
button
· «auto» will disappear
·a new buttonhole length
can be programmed
185_BA_engl 16.4.2004 11:30 Uhr Seite 32
030866.51.04_0401_a185_EN
33Buttonholes 33
Automatic buttonholes (round, keyhole and hand-look)
Auto buttonhole
· machine sews circle or eye automatically
· machine sews the first bead backwards automatically
· machine sews straight stitches forwards up to circle or eye
· machine sews 2nd bead backwards automatically
· machines sews bar tack automatically
· machines sews securing stitches automatically
· machine stops and returns automatically to the beginning of the button-
hole
· all subsequent buttonholes will be sewn automatically to the same
length (without pressing the securing button)
Note:
The graphics shown on the screen are the
same as for a standard buttonhole (see
above) when stitching a round or keyhole
buttonhole
For buttonhole example, refer to the
artista 185 Sewing Manual, page 26..
Both beads of the buttonhole are sewn in the same direction.
Buttonhole length = buttonhole opening in mm
Sewing the first straight stitches
· the sewn section will be displayed on the screen (to the
right of the presser foot indicator)
· sew straight stitches forwards, stop the machine at the
desired length
Programming the buttonhole
·press the quick reverse button
· when auto appears under the buttonhole symbol, the
buttonhole is programmed
Deleting saved buttonholes
·press the external «clr»-button
· «auto» will disappear
·a new buttonhole length can be programmed
Automatic buttonhole (all types) Direct entry length
If the desired length of a buttonhole is known, it can be directly entered
into the machine (in millimeters).
When using the Automatic buttonhole foot No.3A for stitching keyhole
buttonholes, the maximum length that should be entered is 24 mm.
That leaves room for the keyhole, which the machine will add automati-
cally.
Direct entry function
· buttonholes can be sewn to a specific length with the
automatic buttonhole foot No.3A
· select type of buttonhole
· touch buttonhole with question mark symbol
Enter the length
· numbers 1–0 appear on the screen
· enter the buttonhole length
(429 mm) with numbers
· the length appears to the right of the buttonhole symbol
· touch OK to confirm, screen changes automatically
Buttonhole length =
buttonhole opening in mm
Corrections:
· touch del to delete wrong numbers
Back to buttonhole menu
· touch esc
3A
3A
185_BA_engl 16.4.2004 11:30 Uhr Seite 33
030866.51.04_0401_a185_EN
34 Buttonholes
Automatic buttonhole (all types)
Length calculated from button
Determine button size
·a scale appears on the screen
· hold the button (427 mm) against the bottom left corner of the
screen
· use the external stitch width knob to move the vertical line on the
screen, changing the size of the box around the button
· the buttonhole size is shown in mm on the right, e.g. 20 mm
Back to buttonhole menu
· touch OK to confirm and return to buttonhole screen
The buttonhole size can be determined by holding a button on the
screen. The length will be determined by the machine and displayed on
the screen.
Open on-screen measuring screen
· select buttonhole
· touch button size function
On-screen display
· ”auto” below the buttonhole symbol indicates that the buttonhole is
programmed
Deleting saved buttonholes
·press the external «clr»-button
· «auto» will disappear
·a new buttonhole length can be programmed
Buttonhole size
· the computer calculates the buttonhole size from the button diameter
·2 mm are added automatically to take the bartacks of the buttonhole
into account
Corrections for thick buttons
· for buttons which are particularly thick, e.g. raised buttons etc., do
not move the vertical line right up to the edge of the button
· move it to within about 1–4 mm of the right edge of the button,
depending on the button height
Recommendation
· sew a test buttonhole on a scrap of the fabric and interfacing you
intend to use
· cut buttonhole open
· push button through hole
· correct the size if necessary
Deleting saved buttonholes
·press the external «clr»-button
· «auto» will disappear
·a new buttonhole length can be programmed
3A
185_BA_engl 16.4.2004 11:30 Uhr Seite 34
030866.51.04_0401_a185_EN
35Buttonholes
Stitch counter buttonholes (all types)
The first bead of the buttonhole is sewn forward and the second,
backwards
Stitch using Buttonhole Foot 3C or Automatic Buttonhole Foot 3A; sew
at a consistent speed.
The appearance of a stitch counter buttonhole can vary on different
types of fabric so it must be reprogrammed for different fabrics.
Presser foot
· select buttonhole
· touch the presser foot 3C symbol
· the machine registers that the stitch counter program has been selected
· the buttonhole length is now measured by the stitch counter,
i.e. number of stitches
1st bead length
· sew the first bead, stopping the machine at the desired
buttonhole length
·press and release the quick reverse button on the frame
Bartack, 2nd bead
· the machine sews the end of the buttonhole and automatically
switches to stitching the reverse bead
· Continue stitching the reverse bead, stopping when the needle is
even with the beginning of the
buttonhole
·press and release the quick reverse button
Bartack, securing stitches
· the machine sews 5 bartack stitches and secures the
buttonhole automatically
· auto appears under the graphic of the buttonhole on the screen
· the buttonhole is now programmed
· all subsequent buttonholes will be sewn as programmed
Changes
· the buttonhole must be reprogrammed after altering the stitch length,
width, or balance
Deleting saved buttonholes
·press the external «clr»-button
· «auto» will disappear
·a new buttonhole length can be programmed
For buttonhole example, refer to the artista 185 Sewing Manual,
page 27.
185_BA_engl 16.4.2004 11:30 Uhr Seite 35
030866.51.04_0401_a185_EN
36 Buttonholes
Buttonhole corrections (all types)
Bead density
· increase or reduce the stitch length
by approximately 2 steps to achieve
the desired effect
Open balance screen
· select buttonhole
· touch Balance
· balance to increase the density
· balance to reduce the density
· Sew buttonhole until area to be
corrected is reached. Adjust balance.
Continue sewing. The correction
will be incorporated in all subsequent
buttonholes.
Recommendation:
· always test sew on the piece of fabric
you intend to use
Delete balance adjustments
·press clr or touch reset
For additional information about
buttonholes, refer to the
artista 185 Sewing Manual, pages 21–28.
Balancing the beads
· balance will influence the bead and
the eye density
· balance affects both beads and the
eye
Buttonhole too wide
· to reduce the width of the
buttonhole, reduce the stitch width
The following adjustments can be made to a buttonhole
and will remain in effect until the machine is turned off.
Permanent adjustments can be made using the Setup
program (see pages 59–72).
One buttonhole of each type may be
saved in special buttonhole memory
banks. This does not affect the
standard memory of the machine.
Long term saving of buttonhole
programs is only possible for
buttonholes originally stitched as
auto-length buttonholes (see pages
32–34)
Once the length of the buttonhole is
determined, the programmed
buttonhole can be saved using the
store function on the toolbar.
3A
Buttonhole in Long Term Memory
Saving the Buttonhole (Store)
·program the desired automatic
buttonhole according to the
directions on pages 32–34
· touch store on the function toolbar
185_BA_engl 16.4.2004 11:30 Uhr Seite 36
030866.51.04_0401_a185_EN
37Buttonholes
stitches are preprogrammed
· use an awl to punch the keyhole
before cutting the buttonhole open
Leave program
· touch esc
· screen reverts to buttonhole screen
Manual 4 and 6 step buttonholes
Sewing a Four-step Buttonhole (round and keyhole)
Note:
The graphics shown above will ap-
pear on the screen for both the
round and keyhole buttonholes .
Recalling the Saved Buttonhole
· select the desired buttonhole style
· touch mem
· touch the buttonhole length or button measurement function to recall the
saved buttonhole
· the length of the buttonhole will appear on the screen
Changing the Saved Buttonhole
· select the desired buttonhole style
· touch mem
· touch the buttonhole length or button measurement function to recall the
saved buttonhole
· change the length, and touch OK to confirm
· touch store
·programming a new length overrides the existing stored one
Manual buttonholes are ideal when
making single buttonholes or for
repairing existing buttonholes.
The number of steps depends
on the type of buttonhole selected.
Note:
A manual buttonhole cannot be
saved.
Open buttonhole screen
· select buttonhole
· touch the “man” function
Step symbols
· step symbols appear on the screen
for the buttonhole selected
· the arrow in the circle is on “0”
when the buttonhole is selected
· standard buttonhole has 6 steps
·round buttonhole has 4 steps
· keyhole buttonhole has 4 steps
For buttonhole examples, refer to
the artista 185 Sewing Manual,
page 28.
Sewing a 4-step buttonhole
· touch “1”
· sew the 1st bead
· stop the machine at the desired
length
· touch “2”
· machine sews the keyhole or eye
· touch “3”
· machine sews the 2nd bead in
reverse
· stop machine at the first stitch
· touch “4”
· machine sews the top bartack and
securing stitches before stopping
automatically
· length of beads is determined by
the user
· bartack, keyhole, and securing
185_BA_engl 16.4.2004 11:30 Uhr Seite 37
030866.51.04_0401_a185_EN
38 Buttonholes
stops automatically
· length of beads is determined by
the user
· bartacks and securing stitches are
preprogrammed
Leave program
· touch esc
· screen reverts to buttonhole screen
Straight stitched buttonholes are
particularly useful for reinforcing
satin stitched buttonholes on all soft
and loosely woven fabrics such as
wool, or for buttonholes which are
subject to extreme wear. They are
also useful for stitching bound
buttonholes and reinforcing button-
hole openings in leather, vinyl, or
felt.
Straight stitched buttonholes
· select stitch No. 59
· the sequence is determined by the
presser foot used
· this program functions exactly the
same as the corresponding
buttonhole program which will be
stitched over the straight stitched
buttonhole
Automatic buttonhole foot
No. 3A – programming is exactly
the same as for the auto button-
hole program (page 32–34)
Buttonhole foot 3C – programm-
ing is exactly the same as for the
stitch counter buttonhole
program (page 35)
Alter the distance
· alter the stitch width if the distance
between the two rows of stitching
is too narrow or too wide
Straight stitch buttonholes
Sewing a Six-step Buttonhole
Note: The graphics shown on the screen (see below) are the same when stitching the standard, narrow, and
stretch buttonholes.
Sewing the buttonhole
· touch “2”
· machine sews straight stitch
backwards
· stop machine at the first stitch
· touch “3”
· machine sews the top bartack and
stops automatically
· touch “4”
· machine sews the second bead in
the forward direction
· stop machine
· touch “5”
· machine sews the bottom bartack
and stops automatically
· touch “6”
· machine sews securing stitches and
Sewing a 6-step buttonhole
· touch “1” on the screen
· symbol shows section of button to
be sewn
· sew the 1st bead
· stop the machine at the desired
length
185_BA_engl 16.4.2004 11:30 Uhr Seite 38
030866.51.04_0401_a185_EN
39
Buttonholes
Cutting buttonholes open
Buttons with 2 and 4 holes can be
sewn on by machine.
Button sew-on program
· select stitch 60
· the button sew-on foot No.18
· the distance (shank) between the
button and fabric can be adjusted
as desired
Sew button on
2-hole buttons
· adjust the stitch width if necessary
to equal the distance between the
holes of the button
· machine stops automatically at the
end of the program
· wind thread ends around the
thread under the button to create a
thread shank
Button Sew-on program
18
Eyelet program
Eyelets
· select eyelet No. 61 (zig-zag) or
No. 62 (straight stitch)
Sewing the eyelet
· machine stops automatically at the
end of the program
Punching the eyelet
· use an awl to punch the hole in the
eyelet
For button sew-on example, refer
to the artista 185 Sewing Manual,
page 29.
For eyelet examples, refer to the
artista 185 Sewing Manual, page 30.
4 hole buttons
· adjust the stitch width if necessary
to equal the distance between the
holes of the button
· sew the two front holes
· move work forwards
· sew two back holes
· wind thread ends around the
thread under the button to create a
thread shank
Seam ripper
· use the seam ripper to cut the
buttonhole open, starting at each
end and working towards the
middle
Buttonhole cutter and block
· place the fabric on a piece of
wood
· position the cutter in the center of
the buttonhole
·press the handle of the cutter to
punch the buttonhole
185_BA_engl 16.4.2004 11:30 Uhr Seite 39
030866.51.04_0401_a185_EN
40 Alphabets/Numbers
Alphabets/Numbers
There is a choice of five different
alphabet styles.
Each alphabet can be sewn in two
sizes.
Large monograms can be sewn in
three sizes.
For alphabet example, refer to the
artista 185 Sewing Manual, page 42.
Alphabets
·press the external Alphabet button
· the Alphabet menu appears
· screen shows:
· Block letters
· Double block letters
· Upper case italics
· Lower case italics
· Monograms 30/20/15 mm (side-
ways motion)
· touch to select style
· the selected style is activated
Screen: Letter selection
· the presser foot indicator and
needle stop symbol are in the usual
positions
· scroll up and down to select letters
and numbers
Alter size
· when an alphabet is selected the
larger size is activated
· touch symbol
· the highlighted area changes
· this indicates that the smaller size is
active
· touch symbol again
· the larger size is now active
Monogram sizes
· when monograms are selected,
size 1 = 30 mm is automatically
activated
· touch symbol
· size 2 = 20 mm is activated
· touch symbol
· the right field is activated
(3 =15 mm)
· sizes 2 and 3 sew continuously
(starting at left lower edge and
ending at right lower edge) and
work with the memory for writing
words
· size 1 monograms are single motifs
(machine stops automatically after
each one) secured with the secur-
ing
stitch
· Size 1 monograms have templates
to aid in positioning (see page 51)
185_BA_engl 16.4.2004 11:30 Uhr Seite 40
030866.51.04_0401_a185_EN
41Alphabets/Numbers
Programming letters/numbers
Continue programming
· touch to select the next letter
· the letter appears in memory
· continue in this manner
· for additional information on
saving in memory, see pages 42–47
Monogram letters in memory
· it is possible to combine monogram
letters in memory
· the distance between letters is
programmed with the 16
directional sewing program
(see page 49)
· note the beginning and end of
each letter
For alphabet example, refer to the
artista 185 Sewing Manual, page 42.
Programming
· open memory
· touch to select letter
· the letter appears in memory
· the cursor moves to the right in
front of the letter
185_BA_engl 16.4.2004 11:30 Uhr Seite 41
030866.51.04_0401_a185_EN
42 Memory
Programming stitches
Basic Programming
· select the desired stitch
· make any desired adjustments to
stitch width, stitch length, and
needle position
· open the memory by pressing the
external mem button
· touch mem 1 to access the memory
storage screen
Note:
If the machine has been turned off
since the last time the memory
feature was used, mem 1 will show
on the screen when the memory is
activated. If the machine has not
been turned off, the last memory
bank opened will show
· select an empty memory bank
· touch OK to return to the previous
screen
· select the desired stitch
· the stitch appears in the mem field
· the cursor moves to the right as
stitches are selected
Memory
Stitches, letters and numbers can be
programmed, saved and corrected in
memory.
The memory has a capacity of 1023
stitches that can be divided into 255
memory segments or banks. The
memory banks are as large as requir-
ed, depending on the number of
stitches that are saved in each one.
The memory is long-term, i.e.
contents remain saved until they are
deleted or overwritten. Power
disconnections or long periods of
non-use do not have any effect on
the memory contents.
Any alterations to stitch length,
stitch width, and needle position
should be made before entering the
stitch into memory.
In contrast to the stitch menu,
selected stitches are shown turned
90˚ counter clockwise in the memory
bar. The sewing direction is always
from left to right on the memory bar.
For memory examples, refer to the
artista 185 Sewing Manual, pages
40–42.
Open Memory
·press the external mem button
· the memory bar appears on the
screen
· the third row of stitches disappears
from the screen
· scroll up and down to view these
and further stitches
· the cursor appears as a vertical line
in the memory bar
· all changes (programming,
inserting functions, corrections)
affect the character to the left of
the cursor
· the function toolbar at the bottom
of the screen changes automatically
to include those functions appro-
priate for memory
· the opened memory bank is
indicated by its number in the
bottom bar
Open Memory
185_BA_engl 16.4.2004 11:30 Uhr Seite 42
030866.51.04_0401_a185_EN
43Memory
Continue programming
· select the next desired stitch
· the stitch appears in the mem field
· continue in this manner
· start sewing; when the foot control
is pressed, the cursor will go to the
beginning of the stitch combination
for sewing the complete grouping
Note:
If the contents of the memory have
been changed using the edit function
(page 44), the Pattern begin function
must be selected to start the
stitching at the beginning of the
combination.
· use Pattern repeat to stop auto-
matically:
Toolbar function – Pattern repeat
will stop after the selected number
of combinations have been stitched
Pattern end –Single pattern will
stop after stitching the stitch
pattern to the left of the cursor
· to save, touch store
· store will blink once to indicate it is
saving
Scroll memory
· scroll arrows are to the right and
left of the memory bar
· touch to view the programmed
contents either forward or
backward
· to close the memory, press the
external memory button
· if the stitch combination has not
been saved, a message screen will
appear asking if you would like to
save it
Programming stitches by number
Stitches by number
· open memory
· touch function 0–9
· numbers appear on the screen
· the memory bar remains visible
· touch numbers to select stitch
· the number selected appears above
the other numbers
Correct
· touch del in the upper right corner
to change the stitch number
· the cursor moves to the left and
deletes the number
· select new number
· touch del in the lower toolbar to
delete a programmed stitch
· the stitch to the left of the cursor
will be deleted
Confirm and continue programming
· touch OK to confirm
· the stitch selected appears in the
memory bar
· touch store to save in memory
· select the next stitch by pressing
the appropriate number and
proceed as above
Back to stitch screen
· touch esc
· the screen reverts to the stitch
screen which includes the selected
stitch
· the selected stitch is activated
(highlighted)
185_BA_engl 16.4.2004 11:30 Uhr Seite 43
030866.51.04_0401_a185_EN
44 Memory
Editing memory contents
Stitches with functions
· stitches can be modified after being
programmed into memory
·program the first two stitches
normally
· touch edit
· all available functions appear in the
top right section of the screen
· the last stitch in memory (left of
cursor) appears above the editing
functions
Visible functions (in memory bar)
· the securing function appears as a
function in the memory bar
· delete unwanted functions from the
memory bar before continuing with
programming
· touch edit to close
Note:
Functions such as Long stitch and
Pattern extend can be used with
sideways motion stitches,
however, they will be distorted,
so it is not recommended.
Memory functions
The following functions become available in the center
of the screen when the edit function of the memory fea-
ture is selected. All functions on the toolbar (except del)
will become inactive when the edit function is selected
and will reactivate when the edit function is closed. For
more information on these functions, see pages 29–30.
Motor Speed
Securing
Function
Memory
Sub-divider
Tension
Mirror Image –
left/right
Mirror Image –
up/down
Balance
Letter Size
Inserting functions, e.g. mirror image
· place the cursor to the right of the
stitch to which mirror image is to
be applied
· touch edit
· select mirror image in the functions
screen
· the stitch will be shown in mirror
image
· the same procedure for insertion
applies to all functions
· touch edit to close
Long Stitch
Pattern Extend
Monogram
Size
185_BA_engl 16.4.2004 11:30 Uhr Seite 44
030866.51.04_0401_a185_EN
45Memory
Inserting a stitch in memory
· place cursor where the stitch is to
be inserted
· select stitch/letter
· the new stitch is inserted to the left
of the cursor
View memory contents
· touch check
· the memory contents appear in a
window
· the cursor is visible
· the cursor can be moved into
position with the arrows for editing
applications
· after viewing, touch esc
· the window closes and the memory
bar appears
· the cursor is in exactly the same
place as it was in the view window
View memory contents
Corrections while programming in memory
Deleting the last programmed
stitch/letter
· touch del
· the last stitch entered (left of
cursor) is deleted
Deleting a stitch/letter within a
memory
· place the cursor to the right of the
stitch to be deleted
· touch del
· the stitch to the left of the cursor is
deleted
Rule:
All changes and corrections are always made to the left of the cursor.
185_BA_engl 16.4.2004 11:30 Uhr Seite 45
030866.51.04_0401_a185_EN
46 Memory
Open individual memory
Returning to a previously
programmed memory bank
· open memory by pressing the
external mem button
· touch mem 1 on the functions
toolbar
· the Memory storage screen opens
Note: if the machine has been
turned off since the last time the
memory feature was used, mem 1
will show on the screen when the
memory is activated. If the machine
has not been turned off, the last
memory bank opened will show.
· an overview of the memory banks
appear on the screen
· the open memory bank is
highlighted (dark gray)
· the occupied memory banks are
displayed in light gray
· empty memory banks are shown in
white
· memory banks can be scrolled if
more than 15 are occupied (can be
up to 255 memory banks)
· select an occupied memory bank
· the contents are shown in the
memory bar
· touch esc to return to the previous
screen
· the contents of the selected
memory remain active
· you can sew, insert, or correct
these contents
Note:
Contents of memory should be sewn
from a stitch screen, not the memory
storage screen.
Memory capacity
Open Memory storage screen
· open memory by pressing the
external mem button
· touch mem on the functions
toolbar
· the memory bank screen appears
· the total capacity used by stored
stitch patterns is shown in % in the
top row
· total capacity of all memory banks
together is 1023 stitches
Saving memory contents/leave memory
Save and leave memory
· touch store
· the contents are saved
· the memory can be opened and
viewed at any time
· touch external mem button
Turning off machine without saving
· memory contents will be lost if the
machine is turned off without
touching store
185_BA_engl 16.4.2004 11:30 Uhr Seite 46
030866.51.04_0401_a185_EN
47Memory
Memory sub-divider
· the contents of a memory can be
sub-divided as desired, e.g. name,
street, town, etc. by using the edit
feature
·program the name
·program the street
· touch edit
· place cursor after the last letter of
the name
· select Memory Sub-divider
· the sub-divider is inserted to the
left of the cursor
· the characters belong to the one
memory (e.g. mem 4) but are
totally independent of one another
so they can be sub-divided as
desired
Sewing
· activate Pattern begin and sew
Note: when Pattern begin is
activated, the cursor will move to
the right of the first letter in that
memory bank. Stitching will start
with the letter to the left of the cur-
sor.
· the machine only sews the contents
of that particular sub-divider
· to sew the next section, place the
cursor anywhere in that section
· begin sewing; when the foot
control is pressed, the cursor will
go to the beginning of the stitch
combination for sewing the
complete grouping
Note: if the contents of the
memory have been changed using
the edit function (page 44), the
Pattern begin function must be
selected to start the stitching at the
beginning of the combination.
· if a section is to be sewn only once,
touch Pattern repeat 1 on the
function toolbar
Memory sub-divider
Deleting memory
Delete memory
· open memory (press external
button)
· touch mem on the functions
toolbar
· an overview of the memories
appears
· touch memory of choice
(e.g. mem 3)
· touch del
·a message will appear asking if you
really want to delete the contents
of the memory
· touch yes
· the memory contents are deleted
· touch esc to return to the previous
screen
Note:
Fabric should be repositioned as
needed to stitch each section of the
memory.
185_BA_engl 16.4.2004 11:30 Uhr Seite 47
030866.51.04_0401_a185_EN
48
16 directional sewing
16 directional sewing
· select one of the two stitch choices
for 16 directional sewing:
· 39 – Straight Stitch
· 40 – Zig-zag Stitch
·a presser foot symbol with 16
directions appears on the screen
· touch the right and left curved
arrows to alter the stitch direction
· touch continuously to alter
direction quickly
· the machine sews the selected
stitch in the direction chosen
Straight stitch
· the stitch length is preprogrammed
at 3mm (in all 16 directions)
Note: The screen will show the
stitch at 1 mm. When stitching, the
needle hesitates to allow for the
movement of the fabric and
actually penetrates the fabric only
every third stitch, resulting in a
3 mm length
· the stitch length can be shortened,
but not lengthened
Sewing
· select direction and sew
· select new direction and continue
to sew
· continue in this manner as desired
Zig-zag
· the stitch length is programmed to
satin stitch
· the stitch length can be shortened
or lengthened to 1 mm
· the stitch width can be altered from
0–9
Note: When stitching with a width
wider tha 6 mm – 7 mm, it is critical
to adequately stabilize the fabric to
prevent puckering and tunneling.
Sewing
· select direction and sew
· select new direction and continue
to sew
· continue in this manner as desired
For examples of 16 directional
sewing, refer to the artista 185 Sewing
Manual, pages 43–44
Quilt stitches/16 directions/4 directions
Quilt stitches
Quilt stitches
· selection of various stitches which
are particularly suitable for
quilting, piecing, applique, and
crazy patchwork:
· 324 Quilters Securing Program
· 325 Quilting Straight Stitch
· 326 Short Straight Stitch
· 327 Stippling Stitch
· 328 Hand-look Quilting Stitch
· 329 Blanket Stitch
· 330 Heavy Blanket Stitch
· 331 Blindstitch
· 332 Feather Stitch
· 333–338, 351 Feather
· 346–350 Quilting Stitch Variations
· 352 Blanket stitch (dual)
· 353 Double blanket stitch (dual)
· touch to select desired stitch
· the stitch is activated
· all normal information and
functions are visible on the
screen
· stitch length and width can be
adjusted as desired
Quilt stitches/
Directional sewing button
· the menu of the 3 categories
appears:
· quilt stitches
· 16-directional sewing
· 4-directional sewing
· touch to select the category of
your choice
· the menu of all stitches in that
category appears
quilt stitches
16 directions
4 directions
Quilt stitches/directional sewing
185_BA_engl 16.4.2004 11:30 Uhr Seite 48
030866.51.04_0401_a185_EN
49Directional sewing
16 directional sewing – straight stitch with long stitch function
Straight stitch with long stitch
function
·press the external quilt/directional
button
· touch the 16 direction symbol
· select straight stitch
· activate the long stitch function –
every third stitch will be sewn
Note: Without the long stitch
function, the needle hesitates to
allow for the movement of the
fabric, stitching every third stitch.
When the long stitch function is
activated, the needle will hesitate
for 9 stitches.
· the long stitch function is now
highlighted on the toolbar at the
lower edge of the screen
· select direction
· the machine sews in the direction
chosen, stitching 9 mm straight
stitches
Application
The combination of straight stitch
and the long stitch function is
particularly useful for joining large
motifs or letters (see page 44 of the
Sewing Manual artista 185). The
connecting stitches can be removed
after the sewing is complete.
16 directions programmed into memory
Straight stitch in memory
·press the external quilt/directional
button
· touch the 16 direction symbol
· open the memory by pressing the
external mem button
· if the memory bank displayed is not
empty, touch mem to access the
memory storage screen
· select an empty bank (indicated by
a white space)
· touch OK to confirm the selection
· select straight stitch
· select the desired direction by using
the curved arrows in the center of
the screen
·a presser foot symbol with a thin
arrow is displayed in the memory
toolbar
· the presser foot symbol is turned
90˚ to the left
To see the true stitching direction,
look at the front (toes) of the
presser foot symbol and note the
direction of the arrow
· each presser foot symbol represents
three 3 mm straight stitches for a
total of 9 mm of stitching
· to sew a longer distance in the
same direction, touch the symbol
the appropriate number of times to
enter several “presser feet” into
the memory
Zig-zag in memory
· follow the directions above,
selecting the zigzag stitch instead
of the straight stitch
·a presser foot symbol with a thick
arrow is displayed in the memory
toolbar
· each presser foot symbol repre-
sents 9 mm
· when stitching with a directional
zigzag stitch, adequate stabiliza-
tion is critical to prevent puckering
and tunneling of the fabric
185_BA_engl 16.4.2004 11:30 Uhr Seite 49
030866.51.04_0401_a185_EN
50 Directional sewing/sideways motion stitches
Sewing in 4 directions without turn-
ing the fabric is particularly useful for
mending worn areas in tubular items
(sleeves, trousers, etc.) and can also
be used in some decorative tech-
niques.
4 directions
· select 4 directional stitching
· select one of the eight stitches:
· 41 Straight Stitch
· 42 Zig-zag Stitch
· 43 Jersey Stitch
· 44 Running Stitch
· 45 Double Overlock Stitch
· 46 Blanket Stitch
· 47 Super Stretch Stitch
· 48 Honeycomb Stitch
·a presser foot symbol with 4 direc-
tions appears in the center of the
screen
· use the curved arrows to select the
desired direction
· the stitch length and width of these
stitches cannot be altered when a
direction other than forward is
selected
Sewing direction
· the machine sews the selected
stitch in the direction chosen
Sewing
· after direction has been selected,
sew for the desired distance
· stop the machine when desired
· select new direction and sew
· stop machine when desired
· continue sewing in this manner as
desired
Tip
· for quicker sewing, select the
Pattern repeat 1–9 function
· for applying a patch, the easiest
way to work is to sew in a square
from top to bottom and from right
to left (clockwise)
4 directional sewing
For examples of 4 directional sewing,
refer to the artista 185 Sewing Manual,
page 45.
Sideways motion stitches – Outline Designs
Sideways motion stitches are large
decorative motifs stitched in outline
which require the fabric and feed
dogs to move from side to side as
well as backwards and forwards.
Sideways motion stitches are
programmed in one size and cannot
be altered.
Note: Different types of fabric,
interfacings, and stabilizers can
affect the stitching of the motifs.
Adjustment can be made using the
Balance function (see pages 52–53).
For examples of sideways motion
stitching, refer to the artista 185 Sewing
Manual, pages 46–48.
Decorative motifs
·press the external button for deco-
rative stitches
· the decorative stitch menu appears
on the screen
· select a group of sideways motion
motifs (indicated by the cross
symbol)
· select the desired motif (use the
arrows to scroll for viewing all of
the patterns if needed)
185_BA_engl 16.4.2004 11:30 Uhr Seite 50
030866.51.04_0401_a185_EN
51Sideways motion stitches
Sideways motion stitches
Sideways motion stitches
· after selecting the desired motif,
the stitch is activated
· all normal information appears on
the screen
·the crossed arrows symbol (at the
top of the screen to the right of the
needle stop) indicates that sideways
motions stitches are activated
· some patterns are single motifs and
the machine stops automatically
when it is complete
· others are designed for continuous
sewing, to be used for borders,
edgings, and decorative stitching
· sewing beginning and end are
usually at different levels within the
stitch, except for those patterns
designed to be sewn continuously
· use the provided templates to aid in
positioning motifs on fabric
Sideways motion stitches in Memory
· sideways motion stitches can be
saved in memory following the
general directions on pages 42–47
· sideways motion stitches can be
joined by using the memory
function and 16 directional stitches
(see page 49)
Templates
· the templates provided show the
motifs in their stitched forms and
sizes
· the stitch beginning is marked with
a circle
· the stitch ending is marked with a
cross
· the presser foot direction is shown
with fine lines
· the presser foot must be placed on
the fabric in the given direction
= START
= END
1015
1022
1023
1026
1024
1025
1027
1028
artista 185
= START = END
811
812
814
816
826
813
artista 185
= START
= END
801
802
805
807
806
artista 185
= STAR
T
= END
artista 185
185_BA_engl 16.4.2004 11:30 Uhr Seite 51
030866.51.04_0401_a185_EN
52 Balance
Balance
Open Balance
· touch function b
· if the function is not visible on
screen, touch the arrow in the
function toolbar to scroll through all
the available functions
All stitches are checked and fully
adjusted before the machine leaves
the factory.
Different fabrics, threads, stabilizers,
and interfacings can affect
programmed stitches so that
sometimes they might not close or
they might overlap, i.e. the stitches
that make up the pattern are too
close together or too far apart.
These effects can be corrected with
the electronic balance so that the
stitch formation can be adjusted
where necessary to suit the fabric.
There are 50 vertical steps and 20
horizontal steps.
Balance for practical and decorative stitches
When sewing soft fabrics such as
jersey or tricot, the fabric tends to
stretch under the presser foot which
also stretches the stitch being sewn.
For example, the Honeycomb stitch
opens up and is too long. Thicker
fabrics might cause the stitch to
overlap, making it too short.
Correcting with balance is very
simple.
Balance
· select any stitch
· touch b to activate balance; balance
screen appears
· when adjusting practical stitches, a
graphic of the honeycomb stitch
appears in the center of the screen
(this is used as the example for all
practical stitches
)
· when adjusting decorative stitches,
a graphic of the satin stitched oval
appears in the center of the screen
(this is used as the example for all
decorative stitches
)
·two malformations are displayed on
either side of the stitch – left too
short and right too long
· the arrows at the bottom of the
screen show in which direction the
stitch must be corrected
If the stitch looks
like this, use this
arrow to correct it.
If the stitch looks
like this, use this
arrow to correct it.
If the stitch looks
like this, use this
arrow to correct it.
If the stitch looks
like this, use this
arrow to correct it.
Corrections
Stitch too long:
· touch the arrow shown on the right
· the number of steps activated will
be shown directly above the arrow
· the stitch will be shortened
· the change is not shown on screen
· 2–5 steps are normally sufficient to
correct the stitch (max. 50 steps)
· sew a test and make additional
corrections if needed
Stitch too short:
·proceed as above, using the arrow
on the left
· sew a test and make additional
corrections if needed
Returning to stitch screen
· after all corrections are made,
touch OK to confirm the changes
and return to the stitch screen
· touching reset will return the stitch
to the same condition as when the
balance function was opened
185_BA_engl 16.4.2004 11:30 Uhr Seite 52
030866.51.04_0401_a185_EN
53Balance
Balance for sideways motion stitches
Fabric, thread stabilizers, and inter-
facings can affect sideways motion
stitches so correcting with balance
will sometimes be necessary.
Balance
· select sideways motion stitch or
motif
· touch b to activate balance
· balance screen appears
· when balancing sideways motion
stitches, the selected motif is
always shown
· the stitch appears in the center of
the left half of the screen
·two malformations are displayed
either side of the stitch – left too
short and right too long
· the right half of the screen shows
the horizontal balance possibilities
Vertical corrections
· if the appearance of the sewn
stitch is similar to the one on the
right of the screen, use the right
arrow to correct; the pattern will
be shortened
· if the appearance of the sewn
stitch is similar to the one on the
left of the screen, use the left
arrow to correct; the pattern will
be lengthened
· 1–5 steps are normally sufficient to
correct the stitch vertically (max.
50 steps)
· if more than 10 steps are neces-
sary, the stitch will become smaller
· sew a test and make additional
corrections if needed
Horizontal corrections
· the horizontal balance is shown in
the right half of the screen
· the stitch might possibly become
too wide after vertical corrections
have been made, i.e. the center
line of the stitch becomes distorted
· if the center of the stitch has been
pulled to the right, correct with the
left arrow
· if the center of the stitch has been
pulled to the left, correct with the
right arrow
· 5–10 steps are normally sufficient
to correct the stitch horizontally
(max. 20 steps)
· sew a test and make additional
corrections if needed
Returning to stitch screen
· after all corrections are made,
touch OK to confirm the changes
and return to the stitch screen
· touching reset will return the stitch
to the same condition as when the
balance function was opened
If the stitch
looks like
this, use
this arrow to
correct it.
If the stitch
looks like
this, use
this arrow
to correct it.
Use these
arrows to
correct
horizontal
distortions
185_BA_engl 16.4.2004 11:30 Uhr Seite 53
030866.51.04_0401_a185_EN
54 Help Program
Help
The Help program provides on-
screen explanations about individual
stitches and all functions, elimina-
ting the need to refer regularly to
the instruction manual. The informa-
tion shown corresponds to informa-
tion in the instruction manual, but is
quicker and easier to find electroni-
cally.
No matter which screen is displayed,
the help feature for stitches and
functions can be opened. Touch esc
to return to the previous screen .
Opening help
·press the external ? button
· select the desired stitch or function
·a clock on the screen shows that
the computer is searching for the
desired information
Help screen/Functions
· the screen offers the following
information:
· name of the function
· explanation
· brief listing of main applications
Back to previous screen
· touch esc
· Help is closed
· the previous screen appears
Note
The Help program can be opened
at any time without affecting the
work at hand.
Help screen/Stitches
· the screen offers the following
information:
· name of the stitch
· suitable fabrics
· brief listing of main applications
185_BA_engl 16.4.2004 11:30 Uhr Seite 54
030866.51.04_0401_a185_EN
55Thread tension/Tutorial/Creative Consultant
TTC button
·press the external TTC button
· menu appears
· select Thread Tension
· thread tension screen appears
Thread tension
Basic tension settings apply
automatically when a stitch or
program is selected. The tension is
factory set for best possible sewing
results using a 100 weight, 2 ply
polyester thread
(
100/2
)
.
The tension may vary when using
other types of thread such as
embroidery thread, and it may be
necessary to adjust it to suit the
fabric and stitch type.
Changes can be made to the tension
of any stitch without affecting any
other stitches. To do this, the tension
function is accessed with the
external TTC button. It can also be
placed as a function on the toolbar
on the lower part of the screen and
accessed directly from the screen
(see page 28).
Altering the tensions
· the perfect stitch formation is
shown in the center graphic
· the basic value is indicated by the
bar on the scale
· touch the arrows up or down to
alter the tension:
touch the up arrow if the stitch -
formation looks like the top
example
= need tighter upper thread tension
(the upper thread is loose which
allows it to be pulled further
through to the underside of the
fabric)
touch the down arrow if the stitch
formation looks like the bottom
example
= need looser upper thread tension
(the upper thread is tight which
pulls the lower thread further
through to the top of the fabric)
· the tension alteration affects only
the selected stitch and does not
remain saved when the machine is
off
Save and close
· touch OK to confirm the change
and return to the stitch screen
Back to basic settings
·touch reset to return tensions to
the basic settings
185_BA_engl 16.4.2004 11:30 Uhr Seite 55
030866.51.04_0401_a185_EN
56 Thread tension/Tutorial/Creative Consultant
Tutorial
In computer language, tutorial
means self-help. The tutorial
provides concentrated on-screen
information about various aspects of
the machine.
Subjects
· the Tutorial sub-menu appears:
· Beginning to Sew
· FHS system
· Help
· Tips and Tricks
· CPS
· Embroidery module
· Embroidery Software
· touch to select the desired subject
· touch OK to confirm
· to change subjects, touch esc to
return to menu
External TTC button
·press the external TTC button
Menu
· the following menu appears:
· Thread tension
· Tutorial
· Creative Consultant
· touch Tutorial
Information
·a clock on the screen shows that
the computer is searching for the
desired information
· information about the subject of
your choice appears on the screen
· touch esc to close the screen and
return to the menu
Creative Consultant
The Creative Consultant provides
information and help for a variety of
sewing needs.
After entering the type of fabric and
technique you wish to use, the
Creative Consultant provides
suggestions regarding needles,
presser feet, interfacings, special
settings, etc. The suggested presser
feet are not necessarily standard with
the machine but may be special
accessories which can be obtained
from your BERNINA dealer.
External TTC button
·press the external TTC button
185_BA_engl 16.4.2004 11:30 Uhr Seite 56
030866.51.04_0401_a185_EN
57Thread tension/Tutorial/Creative Consultant
Menu
· the following menu appears:
· Thread tension
· Tutorial
· Creative Consultant
· touch Creative Consultant
Techniques menu
· several common sewing techniques
appear on-screen:
· Seaming
· Overcasting
· Topstitching
· Buttonhole
· Zipper
· Decorative work (decorative
stitches)
· Machine quilting
· Freemotion machine quilting
· Appliqué
· Sideways motion patterns
· touch to select the desired
technique
· if the technique you want to use is
not listed, select a similar technique
· touch OK to confirm and move to
the information screen
Fabric menu
·3 columns of fabric types are
displayed
· light-weight fabrics
· medium-weight fabrics
· heavy-weight fabrics
· the most commonly used fabrics are
listed in the three columns
· if the fabric you wish to use is not
listed, select a similar type of fabric
· use the arrows to scroll up and
down for all choices
· touch to select the desired fabric
· touch OK
Information, special suggestions,
thread tension
· the screen displays settings and
suggestions for the type of fabric
and technique you have chosen:
· Presser foot number(s)
· Needle size and type
· Feed dog position
· Thread tension
· Presser foot pressure
· Stabilizer needed
· Special suggestion
· the default tension for the sitch is
set automatically (auto appears)
· there may be several suggestions
for the presser foot and needle
type
· some presser feet suggested may
be special accessories which are
particularly suitable for the chosen
technique (they may not be
standard accessories, but can be
purchased separately)
· select the presser foot and needle
according to your particular wishes
and preferences
·a stabilizer will be suggested if it is
required to suit the technique and
fabric
·provides a reminder to use button-
hole cord (gimp) if necessary to
reinforce a buttonhole
Back to selected stitch
· touch OK to confirm
· the machine will automatically go
to the appropriate practical stitch
screen with the correct stitch and
default tension setting automati-
cally selected
· if decorative work was selected,
the machine will go to the first
screen of decorative stitches with
stitch 101 selected
· sewing can begin immediately
· the suggested stitch can be
changed at any time
185_BA_engl 16.4.2004 11:30 Uhr Seite 57
030866.51.04_0401_a185_EN
58 Smart Function
Smart Function
Sometimes you have to interrupt a
task at hand to complete another
piece of sewing which must be done
before you can carry on any further.
The Smart function was designed
specifically for the purpose of
“remembering” the machine’s
current settings so that you can
return to them later.
The screen in which you are working
with all the settings you made can be
saved and easily re-opened.
Saved settings in the Smart Function
are lost when the machine is turned
off.
Application
· you have created and stored
something in memory
· you have tested or completed some
of the work
· you plan to finish at a later time
Saving the screen with the Smart
Function
·press the external Smart button
· the screen, complete with all the
settings (stitch, functions, memory
etc.) is saved
Second Task
· switch to any appropriate stitch
menu for another task
· complete this task
Smart Function – back to screen
·press the external Smart button
· the original screen appears
· all settings are exactly as you left
them and you can carry on with
your original task
Note:
When switching to the Buttonhole
program, any alterations made are
reverted to basic settings in the func-
tion toolbar.
185_BA_engl 16.4.2004 11:31 Uhr Seite 58
030866.51.04_0401_a185_EN
59Setup Program
Setup Program
The Setup program allows you to
personalize the screen to suit your
own requirements and preferences.
You can change basic settings
permanently and program the F
(Favorite function) button on the
head frame (above the needle).
There are numerous possibilities –
check the headings and decide what
you want to do.
All changes made in the Setup pro-
gram will be saved, even when the
machine is turned off.
The machine can be reset and
returned to the factory settings at
any time.
Setup
·press the external Setup button
· the menu appears
· you can alter any of the features
listed
· the original settings can be reset at
any time
Menu
· the menu lists all those features
which you can alter to suit your
requirements:
· Personal Program
· Functions
· Stitch length/width/needle
position
· Beeper
· Motor speed
· Thread tension
· Start screen
· Return to basic settings
· Sewing light
· Service
· Auto thread cutter
· Screen Contrast
· Thread brand
· personal settings remain saved even
when the machine is turned off
· the machine can be reset to its
original settings or reprogrammed
with desired settings at any time
185_BA_engl 16.4.2004 11:31 Uhr Seite 59
030866.51.04_0401_a185_EN
60 Setup Program
Personal Program
Setup
·press the external Setup button
· menu appears
· touch Personal Program
· Personal Program screen appears
Use the Personal program to design a
screen with the stitches you use most
often. Whether it is made up of
stitches for a certain type of sewing,
such as heirloom or garment, or just
your favorite decorative stitches, this
screen will make it easy and quick to
sew any project.
When inserting stitches into the Per-
sonal program, variations (different
stitch widths, stitch lengths, and
needle positions) of all stitches may
be entered into the Personal program.
Directional stitches and motifs and
alphabets cannot be stored in the
Personal program.
Personal program (programming first
stitch)
· straight stitch always appears as
the first stitch
· personal selections can now be
entered in the “empty” screen
Inserting stitches
·press the Practical stitches external
button
· select Honeycomb stitch (stitch 8)
Personal screen
· the screen changes to the Personal
Program
· Honeycomb stitch appears
· touch store to save the stitch in
your personal program
· when a new stitch is programmed,
it will be inserted automatically
after the last stitch
185_BA_engl 16.4.2004 11:31 Uhr Seite 60
030866.51.04_0401_a185_EN
61Setup Program
Personal program (additional stitches)
· the top row of five spaces is
occupied
· the 6th stitch appears in the next
row
· you can program 45 stitches in the
personal program
· if more than 15 are programmed,
the arrows can be used to scroll the
screen as in the standard program
Save and close
· touch OK
· screen closes and Setup menu
appears
· touch esc to close
·returns to the last stitch screen
opened with the last selection still
highlighted
Personal program function
· to open your personal program, the
Personal Program function must be
inserted in the function toolbar (see
pages 62–64)
Favorite function
· for even easier access, your per-
sonal program can be programmed
into the Favorite function button
located on the frame of the
machine above the needle (see
page 63)
Inserting the second stitch
·press the external buttonhole
button
· touch the round buttonhole
(stitch 54)
Personal screen
· screen changes to personal
program
· the round buttonhole appears on
the screen
· touch store to save the buttonhole
in your personal program
· continue programming in this
manner until all desired stitches are
selected
185_BA_engl 16.4.2004 11:31 Uhr Seite 61
030866.51.04_0401_a185_EN
62 Setup Program
Setup menu
·press the external Setup button,
menu appears
· select personal program
Personal screen
· personal screen appears
· select stitch to be deleted (will be
highlighted)
Stitch deleted
· the stitch is deleted and all
remaining stitches move back one
space
· touch store to save the changes
Deleting stitches from the Personal Program
Programming functions
Delete the stitch
·press the external clr
button
Close
· touch OK
· the screen closes
· Setup menu appears
Setup menu
·press the external Setup button
· menu appears
· touch Functions
Functions screen
· all functions available appear on
the screen
· the bottom two rows of functions
are the same as those that are
active in the practical stitch screen
(includes functions that may be
hidden on the stitch screen)
· these functions can be used in any
screen
· all functions in the lower rows are
active
· the upper two rows of functions
correspond to the lower functions
· the arrows in the center row are
used to move functions
·
There are 7 different function bars
on the artista 185
· Practical stitches
· Decorative stitches
· Buttonholes
·9 mm alphabets
· Sideway motion motifs
· 4- and 16-directional menu
· Monograms
In order to customize a specific func-
tion bar, you must have first selected
a stitch BEFORE you enter the Setup
screen and select the Functions op-
tion. This will activate the correct
function bar and allow it to be custom-
ized in the Setup screen.
185_BA_engl 16.4.2004 11:31 Uhr Seite 62
030866.51.04_0401_a185_EN
63Setup Program
Removing functions
· select Motor Speed in the lower
two rows
· touch the up arrow
· the function disappears from the
lower rows
· the function has now been
transferred to the upper rows and
will no longer appear on individual
screens, such as the practical stitch
screen
· the function is highlighted in the
upper rows and has been deactivat-
ed (removed) from the lower ones
· move and deactivate other
functions in the same way
Insert function
·a removed function can be
reinstated at any time
· select Motor Speed in the upper
rows
· touch the down arrow
· the function is moved to the first
position in the function toolbar in
the lower rows
· all other functions move one space
to the right
Insert new function between two
existing functions
·a new function can be inserted
between two existing functions
· select a function from the upper
rows
· touch the position in the bottom
rows where you want to insert the
function
· touch the down arrow
· the function will be transferred to
the selected position
· the replaced function (the one you
selected
)
and all others will move
one space to the right
Program F (Favorite Function) button
· select any function (including the
Personal Program) from the top two
rows
·press the external F button (above
the needle)
·press the down arrow
· the F button is now programmed
· the programmed function is
displayed on the screen to the right
of the needle stop position symbol
· it can be reprogrammed in the
same manner as often as you like
185_BA_engl 16.4.2004 11:31 Uhr Seite 63
030866.51.04_0401_a185_EN
64 Setup Program
Changing basic settings for stitch width,
stitch length and needle positions
Open Setup
· select stitch for which you want to
alter the width, length, and/or
needle position
·press the external Setup button
· menu appears
· select stitch length, stitch width,
needle position
· This function allows for the custo-
mization of stitches in specific
menus as well as in the Personal
Program. You have the option to
set your own personal stitch
defaults.
Beeper
Changing the settings
· the stitch width, length and needle
position screen appears
· alter the stitch width and length
settings using the external controls
· alter the needle position with the
external buttons
· touch OK to save
· to return to basic settings, touch
reset
· touch esc to close Setup and return
to the last selected stitch screen
Setup menu
·press the external Setup button,
menu appears
· touch Beeper
· beeper menu appears
Return all functions to basic settings
·touch reset
· all functions will be returned to their
original positions except the Favorite
function button on the head frame
· to reprogram the Favorite function but-
ton, follow the same steps
· the new function will replace the old
Save changes and close
· touch OK
· changes are saved
· screen closes
· Setup screen appears
Removing of functions
·press button
· delete function
Adding of functions
·press button
· add function
185_BA_engl 16.4.2004 11:31 Uhr Seite 64
030866.51.04_0401_a185_EN
65Setup Program
Changing the motor speed
Audio signals
· audio signals can be applied to the
following:
· stitches
· functions
· feed-dog raised/lowered
(for embroidery)
· upper thread control
· lower thread control
· position of presser foot (for
embroidery)
· bobbin winder motor
· embroidery end
· audio signals can be turned on and
off
· the number of repeats can be
selected
· the number of beeps can be set at
1, 2, or 3
Adding a signal
· select desired item from the menu
· touch on
· touch the number pad until the
number of beeps you want
(
1, 2, or 3) is highlighted
Deleting a signal
· select desired item from the menu
· touch off
· the audio signal is turned off for
this feature
Note:
Turning off the beepers for the
Upper and Lower thread control will
deactivate the sensors as well.
Save and close
· touch OK
· changes are saved
· screen closes
· Setup screen appears
Setup menu
·press the external Setup button,
menu appears
· touch Motor Speed
· menu appears
Change the maximum motor speed
· touch the arrows to alter the
maximum sewing speed (900
stitches/minute is the basic setting)
·a reduction or increase in the motor
speed is reflected in this number
· each touch of an arrow increases or
decreases the number of stitches
per minute by 10
· any change of the maximum speed
affects all 4 speeds (
1
/
4
,
1
/
2
,
3
/
4
,
4
/
4
) =
slower or faster at all four levels
185_BA_engl 16.4.2004 11:31 Uhr Seite 65
030866.51.04_0401_a185_EN
66 Setup Program
Save and close
· touch OK to confirm the change
· touch esc to return to the Setup
menu
· touch esc to return to the last
selected stitch menu
Back to basic settings
· follow the directions above to enter
the motor speed menu
·touch reset to revert to factory
settings
Changing the basic thread tension setting
The basic tension setting of the artista
machine applies to all stitches of the
machine. The tension is factory set for
best possible sewing results using a
100 weight, 2 ply polyester thread
(
100/2
)
. Other types and weights can
affect the stitch, causing a need for a
tension adjustment to get the best
results.
The overall tension setting of the
machine can be tightened or loosened
up to 20% in the Setup program. This
setting will remain in effect until it is
changed again, even if the machine is
turned off.
Changing the tension setting in the
Setup program will affect all stitches
of the machine. Any secondary
changes using the TTC button (see
page 55) will be changed using the
basic setting as a base.
Note: Basic setting refers to the over-
all tension setting of the machine.
This may be the factory setting or your
own if you have adjusted the tension
in the Setup program.
Setup menu
·press the external Setup button,
menu appears
· select Thread Tension
· thread tension screen appears
Altering the tensions
· the perfect stitch formation is
shown in the middle of the left side
of the screen
· the scale shows a possible change
of +/- 20%
· the basic value is indicated by a
fine line at 0
·a changed setting is indicated by a
black bar
· touch the arrows up or down to
alter the tension:
touch the up arrow if the stitch for-
mation looks like the top example
= need tighter upper thread
tension (the upper thread is
loose which allows it to be pulled
further through to the underside
of the fabric)
touch the down arrow if the stitch
formation looks like the bottom
example
= need looser upper thread
tension (the upper thread is tight
which pulls the lower thread
further through to the top of the
fabric)
· touch OK
· the alterations are saved and the
screen closes
· the tension alteration affects all
stitches and remains saved when
the machine is turned off
185_BA_engl 16.4.2004 11:31 Uhr Seite 66
030866.51.04_0401_a185_EN
67Setup Program
Start screen on and off
Return to basic settings
Back to factory settings
·touch reset to return tensions to
the factory settings
Save and close
· touch OK to confirm the change
· touch esc to return to the Setup
menu
· touch esc to return to the last
selected stitch menu
Setup menu
·press the external Setup button
· menu appears
· touch Start Screen
Turn start screen off
· start screen appears
· the start screen can be turned on or
off
· touch off
· the start screen will not appear
next time the machine is turned on
· the practical stitch menu appears
immediately when the machine is
turned on
Turn start screen on
· touch on
· the start screen will appear every
time the machine is turned on,
followed automatically by the
practical stitch menu
Save and close
· touch OK to confirm the change
· touch esc to return to the Setup
menu
· touch esc to return to the last
selected stitch menu
Setup menu
·press the external Setup button,
menu appears
· touch Return to Basic Settings
185_BA_engl 16.4.2004 11:31 Uhr Seite 67
030866.51.04_0401_a185_EN
68 Setup Program
Setup menu
·press the external Setup button,
menu appears
· select Sewing Light
Switch light on/off
· touch on
· light will be on continuously when
machine is turned on
· touch off
· light will not come on at all
Save and close
· touch OK to confirm the change
· touch esc to return to the Setup
menu
· touch esc to return to the last
selected stitch menu
Sewing light
·a message will appear asking you
to confirm that you want to return
the machine to the basic settings
· touch yes; the Setup screen
reappears
·a clock shows on the screen
indicating that all changes
in Setup are being reversed
· touch no; the Setup screen
reappears
· all existing changes to Setup
remain in effect
· a message will appear switch off
and on your machine
· the factory settings are restored
Note:
Returning to basic settings does not
erase your pragrammed and stored
memory banks
185_BA_engl 16.4.2004 11:31 Uhr Seite 68
030866.51.04_0401_a185_EN
69Setup Program
Service
The service function of the Setup
program gives information about the
version of software in the artista
and lets you make calibration
adjustments to the screen and hoop
of the embroidery module (special
accessory).
Setup menu
·press the external Setup button,
menu appears
· touch service
Service Screen
· service screen appears
· select version
Version Information
The version screen shows information
about the version of software loaded
into the sewing machine and embroi-
dery module (special accessory). This
information is helpful if you are
asking questions of the dealer or if
you plan to upgrade the software.
Version information
· version screen appears
· shows the version of software
loaded into the artista sewing
machine
· shows the version of software
loaded into the embroidery module
(special accessory), if applicable
· the embroidery module must be
connected to the machine to show
the version on the screen
· touch esc to return to the previous
screen
185_BA_engl 16.4.2004 11:31 Uhr Seite 69
030866.51.04_0401_a185_EN
70 Setup Program
Service Screen
· service screen appears
· select screen
· select this screen if the on-screen
buttons do not react properly when
selected (touched)
Calibration
· screen calibration screen appears
·press each black point in the center,
one after the other
· it is not important which point is
selected first
· the machine will beep when the
dots are touched to let you know
contact was made
· will automatically go back to the
previous screen
· touch esc to return to the setup
screen
· touch esc to return to last selected
stitch screen
Important Note:
When calibrating the screen, take
care to touch the black dots only.
If the screen is miscalibrated by
touching any area other than the
black dots, it may require a technical
adjustment by an authorized
technician.
Calibrating the screen is important
for making on-screen selections by
touch. If the screen is not calibrated,
you may touch one selection and the
machine will read one next to it. For
precision touch selection, the screen
must be calibrated.
Note: The screen is calibrated at the
factory, but shipping and transport-
ing may affect it.
The screen only needs to be cali-
brated if there is a problem with
precision touching.
Screen Calibration
Setup menu
·press the external Setup button,
menu appears
· touch Service
Embroidery hoop adjustment
This adjustment calibrates the needle
to the center of the embroidery hoop.
The hoop adjustment can only be
activated if the embroidery module is
attached
Setup menu
·press the external Setup button
· menu appears
· touch service
Service Screen
· service screen appears
· select Adjustment of hoop
185_BA_engl 16.4.2004 11:31 Uhr Seite 70
030866.51.04_0401_a185_EN
71Setup Program
Hoop adjustment
· hoop adjustment screen appears
· attach the large hoop to the
embroidery module
· insert the embroidery template into
the hoop
· touch check – the machine reads
the hoop position; the needle
should be positioned exactly over
the center point of the template
· if it is not, adjust with the arrows
· it is only necessary to adjust the
hoop once – the same setting
changes will apply to all the hoops
Save and close
· touch "ok" = close the screen
· touch "esc" = close Setup
· touch "check" in Layout 1 (touch it
longer so that the reference position
is also read)
· the embroidery hoop adjustment is
completed
Automatic thread cut
· touch “off” and the Automatic
thread cutter is turned off
· touch “on” and the Automatic
thread cutter is turned on
Auto thread cut by color change
during embroidery
Save and close
· touch "ok" and the alterations will
be saved
·touch "esc" returns to the Setup
menu
Automatic thread cutter
«Setup»-Menü
· select Auto thread cutter
· screen opens for turning the thread
cutter off/on
185_BA_engl 16.4.2004 11:31 Uhr Seite 71
030866.51.04_0401_a185_EN
72 Setup Program
Setup menu
· select thread brand
Changing thread brand
Changing thread brand
· the color numbers of the selected
thread brands appear now on the
embroidery screen
Save and close
· touch "ok" and the alterations will
be saved
·touch "esc" returns to the Setup
menu
Screen contrast
The contrast of the screen can be
adjusted for easier viewing.
Setup menu
·press the external Setup button,
menu appears
· touch contrast (lower right of
screen)
· contrast screen appears
Adjust contrast
· two adjustments are provided to
adjust the contrast
(– = lighter, + = darker)
· touch to increase or reduce the
contrast
· the original screen is visible on the
left to control and check the
adjustments as they are being made
Save and close
· touch OK
· changes are saved
· screen closes
· Setup menu appears
185_BA_engl 16.4.2004 11:31 Uhr Seite 72
030866.51.04_0401_a185_EN
73eco function / Special Accessories
Leave Setup program
· touch esc
· Setup is closed
· changes are saved
· changes remain saved when the
machine is turned off
Leave Setup program
Eco function
· touch the external eco button
· energy used will be reduced by
50%
· useful when interrupting work for
longer periods
The green eco (ecology) function
button on the front of the machine
saves energy when the machine is
not in use, but you don’t want to
turn it off and lose the settings. It
can be compared to the sleep feature
on a computer.
If the eco function is activated, the
machine uses about 50% less energy.
The screen in which you are currently
working, all memory contents, and
any other functions which you have
selected remain active. The screen
goes dark and details are just visible.
Once you begin working again, the
machine will be returned to its
normal state.
Besides saving energy, the eco
function is also a child safety device.
Once the eco function is activated,
the machine is “locked” and the foot
control is inactive. The machine will
only sew after turning off the eco
function (pressing the button once),
returning it to the last active screen.
eco Function
Return to sewing
· touch the eco button
· machine returns to normal function
· the eco function is cleared when
the machine is turned off
CPS Program
CPS Program
(Customized Pattern Selection)
Using a computer, the installed
Customized Pattern Selection soft-
ware will allow you to exchange and
personalize your sewing stitches and
embroidery designs as often as you
like. Using simple “drag and drop”
motions, replace stiches on the
sewing computer from the complete
database of stitches. Apply the same
technique with the embroidery
designs and alphabets.
Special Accessories
The following pages offer informa-
tion about additional accessories and
attachments available for the artista
sewing machine. These accessories
will add to the capabilities and
versatility of the machine, offering
unlimited possibilities for your
creativity.
Ask your Bernina dealer for more
details!
185_BA_engl 16.4.2004 11:31 Uhr Seite 73
030866.51.04_0401_a185_EN
74 Special Accessories
Inserting the card
· insert the card into the slot in the
module
Embroidery cards
Connecting the embroidery module
· turn the sewing machine off
·remove the accessory box or sewing
table
· position the module on the back of
the free arm
· push the engaging lugs into the
base plate of the machine (back
right)
· insert the plug in the connection on
the right side of the machine
(embroidery module symbol)
· turn sewing machine on
Embroidery module
Embroidery module
(special accessory)
The embroidery module is a wonder-
ful addition to your sewing machine,
offering you unlimited possibilities
to use your imagination and creativi-
ty to their full extent. It provides the
possibility of sewing a wonderful
array of large motifs.
The module attaches to the free arm
and is connected to the right side of
the machine in the connecting
socket provided; it comes prepro-
grammed with 30 assorted motifs.
When selected, they appear on the
screen and can be sewn immediately.
You can position, mirror image,
enlarge and reduce the motifs.
Additional embroidery motifs, cover-
ing a wide range of subjects, are
available on cards. Just insert a card
into the embroidery module, select,
and sew!
A detailed instruction manual is
supplied with the embroidery
module.
Designs
· embroidery menu appears
· touch the embroidery module
symbol to access the
preprogrammed designs
· touch the teddy bear symbol to
access designs from cards
· the position, size, and density of
the motifs can be altered
· designs can mirror imaged, as well
as rotated
·a detailed instruction manual is
supplied with the embroidery
module.
Preprogrammed embroidery design
cards covering a wide range of
subjects can be used in conjunction
with the embroidery module.
New cards are introduced on a regu-
lar basis so that you can build up a
diverse library of beautiful motifs,
each relating to a specific subject or
theme.
The cards are inserted into the
embroidery module. You can then
view the motifs on the screen of
your sewing machine using the scroll
arrows.
185_BA_engl 16.4.2004 11:31 Uhr Seite 74
030866.51.04_0401_a185_EN
75Special accessoires
Embroidery card menu
· the embroidery menu appears
· touch the teddy bear symbol
Embroidery motifs on the card
·the first motif screen appears
· each motif is numbered
· scroll to view further motifs
· select and embroider the same as
for design motifs programmed on
the embroidery module.
Connection cable
· turn the machine off before
attaching the cable
· insert the cable into the
appropriate socket on the right side
of the machine (PC symbol)
· turn the machine on
Detailed instruction manuals are
supplied with the artista software
programs.
PC Embroidery Software (optional accessory)
BERNINA artista Embroidery Software
allows you to combine, mirror image,
rescale and embellish existing motifs.
You can also create and embroider
your own designs up to 145 x 255
mm.The process is controlled by you
from the first stitch on your
screen to the finished motif on
fabric. Each design is uniquely yours.
You design – your machine does the
work!
The finished creations are transferred
directly via a connecting cable (9-pin
serial port on the machine) to the
embroidery module. The designs can
be saved in blank memory cards or
the embroidery module itself.
The Windows format of this PC
program will be familiar to many of
you and is easy to understand and
use. A computer scanner, which can
be purchased at computer stores, is a
real design aid, allowing you to scan
clip art and original designs for
digitizing directly into the software.
Ways to save your PC designs
· on your PC
· on a Personal Design card inserted
in the embroidery module
· on a blank memory card inserted in
the reader/writer box (optional
accessory)
· on the embroidery module itself
185_BA_engl 16.4.2004 11:31 Uhr Seite 75
030866.51.04_0401_a185_EN
76 Needle, thread, fabric feed
Important facts about sewing machine needles
Sewing machine, needle and thread
Your Bernina uses needle system 130/705H.
Needle and thread
The most commonly sold needles are nos. 70–120. The
finer the needle, the lower the number. The table shows
you which needle is suitable for which threads. The
needle size selected must correspond to the thread size.
Needle and
fabric/Condition of needle
The needle must be in
perfect condition. Problems
can occur with damaged
needles.
Correct needle/thread
combination
When sewing, the thread
runs in the long groove on
the needle.
Unsatisfactory
needle/thread combination
If the needle is too fine the
groove on the front cannot
accommodate the thread
and faulty stitching occurs.
bent needle blunt needle burred needle
Needle/
thread table 70 80 90 100 110–120
Darning thread
Embroidery
thread
Mercerized
cotton thread
Synthetic thread
Thick threads,
synthetic merc.
thread
Buttonhole thread
for decorative
seams (cordonnet)
185_BA_engl 16.4.2004 11:31 Uhr Seite 76
030866.51.04_0401_a185_EN
77Needle, thread, fabric feed
Needle size
60–100
70–90
90–100
80–100
60–90
75–90
75–90
75-90
80–100
100–120
100
70–100
80
Model
Normal point, slightly rounded
Ball point
Cutting point
Very fine point
Especially fine point
Fine point
Large eye, slight ball point
Large eye
Small ball point, long eye
Wide needle (wing)
Needle distance: 1.0 / 1.6 / 2.0 /
2.5 / 3.0 / 4.0 / 6.0 / 8.0
Needle distance 3.0
Many fabrics are easier to sew if the appropriate needle is used.
Type of needle
Universal
130/705 H
Jersey/Stretch
130/705 H-S
130/705 H-SES
130/705 H-SUK
Leather
130/705 H-LL
130/705 H-LR
Jeans
130/705 H-J
Microtex
130/705 H-M
Quilting
130/705 H-Q
Embroidery
130/705 H-E
Metafil
130/705 H-MET
Cordonnet
130/705 H-N
Wing needle
130/705 HO
Double wing
needle
130/705 H-ZWI-HO
Double needle
130/705 H-ZWI
Triple needle
130/705 H-DRI
Suitable for
For nearly all natural and
synthetic fabrics (woven and
knitted)
Jersey, stretch fabrics
Natural and synthetic leather and
plastic
Heavyweight fabrics such as
denim, canvas, overalls
Micro fiber fabrics and silk
Straight and topstitching
Embroidery on all natural and syn-
thetic fabrics
Sewing with metallic threads
Topstitching with thick thread
Hemstitching
Special effects with hemstitch
embroidery
Visible hems in stretch fabrics, pin-
tucks, decorative sewing
Decorative sewing
Special needles are available at your BERNINA dealer.
185_BA_engl 16.4.2004 11:31 Uhr Seite 77
030866.51.04_0401_a185_EN
78 Needle, thread, fabric feed
Feed-dog and fabric feed
Height Compensating Tool
Feed-dog and sewing corners
Let the fabric feed evenly!
Holding back will result in
thread build-up.
Pulling or pushing will
result in gaps.
The feed-dog can work
normally when the foot is
level.
If the foot is at an angle,
e.g. when sewing over
thick to thin or vice-versa,
the feed-dog cannot grip
and feed the fabric.
To solve this problem,
place one, two or three
compensating plates as
required behind the needle
under the presser foot.
Correct this by placing one
or more compensating
plates as close as possible
to the edge of the fabric.
When sewing corners
only a small section of
the fabric is actually on
the feed-dog so that it
cannot grip the fabric
well.
The gap between the two
rows of teeth is relatively
large due to the width of the
stitch plate hole.
To correct the height in
front of the foot, place
one or more plates to the
right of the foot next to
the needle. Sew until the
foot is level again and
remove the plates.
Important
Feed-dog and stitch length
With each stitch the feed-dog moves forward by one step.
The length of this step is determined by the stitch length
selected. With an extremely short stitch length, the steps
are short. The fabric moves under the foot quite slowly,
even at full sewing speed. Buttonholes, satin stitch and
some decorative stitches are sewn with a very short stitch
length.
185_BA_engl 16.4.2004 11:31 Uhr Seite 78
030866.51.04_0401_a185_EN
79Cleaning, Maintenance
Replacing the Sewing Light
Contrary to an ordinary bulb, the CFL
sewing light has a better illumination
and a longer life.
Caution:
Please note that a defective CFL
sewing light must ONLY be replaced by
an authorized technician. The sewing
computer must be brought to an
authorized BERNINA dealer!
Cleaning and Maintenance
Cleaning the Hook
· turn power switch to «0» (off) and pull out plug from electric outlet
·remove the bobbin case
· clean the hook race using the brush provided or a cotton swab.
The use of any sharp instrument could damage the hook
· insert the bobbin case
Cleaning the Sewing Computer
· wipe with a soft, damp cloth
· if very soiled, wipe with a solution of water and a few drops
of liquid soap on a damp (not wet) cloth
Important:
Never use alcohol or solvents of any kind
to clean the sewing computer!
If the sewing computer is stored in a cold room, it should be brought to a
warm room about 1 hour before use.
Cleaning the Stitch Plate Area
Periodically remove thread lint and remnants which collect under the stitch
plate and the hook.
· turn power switch to "0" (off) and pull out plug from electric outlet
·remove presser foot and needle
· open the free arm cover
·press the stitch plate down at the back right corner
· lift an remove stitch plate
· clean the area with the lint brush
·replace the stitch plate
Cleaning the Screen
·wipe with a soft, damp cloth
Lubricating
· turn power switch to «0» (off) and pull out plug from electric outlet
· squeeze 1 drop of oil into the hook race
·run the sewing computer for a short time without thread
to prevent oil soiling your work
Please refer to the safety instructions!
185_BA_engl 16.4.2004 11:31 Uhr Seite 79
030866.51.04_0401_a185_EN
80 Troubleshooting
Trouble shooting
In most cases you will be able to identify and remedy
faults by checking the following.
Check whether:
· the upper and lower threads are threaded correctly
· the needle is inserted as far up as possible with the flat
side to the back
· the needle size is correct – check the needle/thread
table
· the machine is clean – brush out any thread lint
· the hook race is clean
· any threads are trapped between the tension discs or
under the bobbin case spring
Upper thread breaks
· upper thread tension is too tight
· needle is not designed to be used with the chosen
thread
· needle has been inserted incorrectly – the flat side of
the shank must be to the back
· needle is bent or blunt
· for additional needle information, check the Creative
Consultant and the charts on pages 71–72
· poor quality, knotted or dried out thread has been used
· use the correct spool disc
· stitch plate or hook tip damaged – take your machine
to your BERNINA
®
dealer
Lower thread breaks
· the lower thread tension is too tight.
· the bobbin is jamming in the bobbin case. Remove and
replace the bobbin.
· the hole in the stitch plate has been damaged by the
needle. This must be polished by an authorized
BERNINA
®
service technician
· the needle is blunt or bent.
Skipped stitches
·wrong needles used – use only 130/705H system
· the needle is blunt, bent or incorrectly inserted – push
completely to the top when inserting.
· the needle point does not suit the fabric being sewn –
if necessary, use a ball point or stretch needle for
knitted fabrics and a cutting point for hard leather.
Needle breaks
· needle clamp screw loose.
· fabric taken out forward instead of behind the presser
foot.
· when sewing over thick area, the fabric was pushed
with the needle still in the fabric.
· poor quality thread, unevenly wound or knotted.
Faulty stitching
·remnants of thread between the tension discs
·remnants of thread under the bobbin case spring
· incorrect threading. Check upper and lower threads
· use the correct spool disc
Machine fails to run or runs slowly
· plug not fully inserted
· power switch in off (0) position
· machine has been standing in a cold room
· bobbin winder engaged
·remnants of thread block the hook system
Machine sews in reverse
·reverse sewing function is activated
Defective sewing-light
Caution:
· Please note that a defective CFL sewing light must
ONLY be replaced by an authorized technician. The
sewing computer must be brought to an authorized
BERNINA dealer!
185_BA_engl 16.4.2004 11:31 Uhr Seite 80
030866.51.04_0401_a185_EN
81Glossary of terms
Glossary of terms
check · to preview the contents of a memory bank
clr (clear) ·remove or restore settings, back to basic settings
cursor · on-screen positioning marker (vertical line)
· used in memory for marking deletions, insertions, etc.
customized · customer-oriented, individualized, personalized
Delete · Delete/clear the previous command
edit · alter, modify
esc (escape) · close screen/program, return to previous or start screen
help · an integrated program providing brief information and help concerning functions and
specific stitches
memory · sewing machine program to store stitches and combinations of stitches, letters and
numbers for recall at any time
menu · summary of program contents, e.g. stitches, functions from which selections can be
made
ok ·to confirm a task or selection before continuing
outline · outline designs = sideways motion stitches; stitches with outer contours which are
not filled in
pattern · motif, stitch
PC · Personal Computer
PC Embroidery Software · User friendly program designed especially for our customers
· PC program for use in conjunction with our embroidery module to edit, mirror image
and rescale existing motifs. You can also use it to create and convert your own design
into beautiful embroidery.
scroll · to move the screen up or down to view
Setup · sequences and settings which can be altered and adapted to suit your personal
preferences
185_BA_engl 16.4.2004 11:31 Uhr Seite 81
030866.51.04_0401_a185_EN
82 Glossary of terms
smart ·program which saves the stitch and all settings in use during interruptions. Toggle
between two stitches.
software · computer programs
store · save in memory for recall at any time
toolbar ·a term used for on-screen groups, e.g. functions
touch screen · screen which operates the machine by touch
tutorial · self-help program for learning about various machine features
update · load new operating software onto the sewing computer that enhances existing
features
upgrade · load new operating software and sometimes, additional hardware pieces as well, to
add new features and capabilities to the sewing computer
185_BA_engl 16.4.2004 11:31 Uhr Seite 82
030866.51.04_0401_a185_EN
83Index
A
Accessory box 6
Alphabets/numbers 40–41
· alter size 40
· monogram sizes 40
· programming 41
Alphabet programming functions 31
B
Balance 52–53
Bobbin – winding, inserting 8
Bringing up the lower thread 10
Buttonhole program functions 30
· button measurement 30
· direct length entry 30
· manual buttonhole 30
· stitch counter buttonhole 30
Buttonholes 32–39
· auto round and keyhole 33
· auto standard and stretch 32
· auto with direct length entry 33
· buttonhole corrections 36
· long-term memory 36–37
· manual 4–6 step buttonholes 37–38
· on-screen button measure 34
· stitch counter buttonhole 35
· straight stitch buttonholes 38
Buttonholes, applications 19
Buttonholes, opening 39
Button sew-on program 39
C
Carrying case 6
Cleaning, maintenance 79
Contents 3
CPS program 73
Creative Consultant 56–57
· Fabric menu 57
· Techniques menu 57
D
Details of the machine 4, 5
Directional sewing 48–50
· 16 directions 48–49
· 4 directions 50
E
eco function 73
Editing functions 29–30
· balance 30
· letter size 30
· long stitch 30
· mirror image 29
· monogram size 30
· motor speed 29
· pattern extend 30
· securing end of stitch 29
· sub-division 30
· tension 29
Embroidery cards 74–75
Embroidery module 74
External stitch buttons 23–24
· alphabet button 24
· buttonhole button 23
· decorative stitch button 23
· practical stitch button 23
· quilt/directional button 24
· Setup 24
External function buttons 24–25
· Automatic thread cutter 25
· clr button 24
· eco button 25
· F (Favorite Function) button 25
· Help 25
· mem button 24
· Needle position 25
· Needle stop adjustment 25
· Quick reverse button 25
· Setup button 24
· Smart button 24
· TTC button 25
Eyelet program 39
F
F (Favorite function) button 63
Fabric feed, thread, needle 76–78
Feed dogs and fabric feed 78
Feed dogs 12
FHS Free Hand System 7
Foot control 7
Functions in memory 29
· check 29
· delete 29
· edit memory 29
· select memory 29
· store 29
· scroll left 29
· scroll right 29
Functions in Setup 28
Functions, on-screen selection 25
G
General functions 26
· esc 26
· OK 26
· Scroll down 26
· Scroll up 26
Glossary of terms 81–82
H
Help program 54
L
Letters/numbers 41
Index
185_BA_engl 16.4.2004 11:31 Uhr Seite 83
030866.51.04_0401_a185_EN
84 Index
M
Maintenance, cleaning 79
Memory 42–47
· Corrections in memory 45
· Deleting memory 47
· Functions 44
· Open memory 42
· Open individual memory 46
· Memory capacity 46
· Programming stitches 42
· Programming stitches by number 43
· Save/leave memory 46
· Sub-divider 47
· View memory contents 45
Messages, on-screen 31
N
Needle threader 10
Needle, changing 9
Needle, thread, fabric feed 76–78
Needle position, altering 21
Needle stop 22
O
Outline designs 50
P
PC Embroidery Software 75
Power cable 7
Power switch 7
Practical stitches, applications 18–19
Presser feet 17
· Reverse pattern foot No.1C 17
· Overlock foot No.2A 17
· Buttonhole foot No.3C 17
· Auto buttonhole foot No.3A 17
· Zipper foot No.4 17
· Blind stitch foot No.5 17
· Jeans foot No.8 17
· Button sew-on foot No.18 17
· Open embroidery foot No.20C 17
· Sideways motion foot No.40C 17
Presser feet, special 17
Presser foot pressure 13
Presser foot, changing 9
Presser foot indicator 22
Programming letters/numbers 41
Q
Quilt stitches/directional sewing 48–50
Quilt stitches 48
S
Safety instructions 1
Screen 20
Selecting on-screen functions 21
Setup 59–73
· Beeper 64–65
· Embroidery hoop adjustment 70–71
· F (Favorite function) button 63
· Functions, programming 62–63
· Functions in Setup 64
· Motor speed 65–66
· Needle position 64
· Personal program 60–61
· Return to basic settings 67–68
· Leave Setup 73
· Screen Calibration 70
· Screen Contrast 72
· Service 69
· Sewing light 68
· Start screen 67
· Stitch width, length 64
· Thread tension 66
· Version Information 69
Sewing light, replacing 79
Sewing machine needles 76–77
Sewing table 7
Sideways motion stitches 50–51
Smart function 58
Special accessories 73–75
Standard accessories 6
Stitch width/length, altering 21
Stitch plate 12
Stitch selection, on-screen 21–23
Stitch selection by number 22–23
Stitch summary 14–16
· alphabets 15–16
· buttonholes 14
· decorative stitches 14–15
· practical stitches 14
· quilt stitches 15
· 16 directional sewing 15
· 4 directional sewing 15
Supplementary spool pin 9
T
Thread cutter 12
Thread, needle, fabric feed 76–78
Thread tension, altering 28, 55, 66
Threading, upper 10
Touch screen functions 26–28
· Balance 28
· Clear All 28
· Continuous reverse sewing 27
· Double needle limitation 28
· Hemstitch (wing) needle 28
· Half pattern 27
· Long stitch 27
· Mirror image 27
· Motor speed 26
· Pattern begin 26
· Pattern end 26
· Pattern extend 27
· Pattern repeat 27
· Scroll 27
· Securing 26
· Stitch selection by number 27
· Tension 28
· Vertical mirror image 27
Touch screen selection 20–24
Troubleshooting 80
Tension/Tutorial/Creative Consultant55–57
185_BA_engl 16.4.2004 11:31 Uhr Seite 84
030866.51.04_0401_a185_EN
Sewing Manual
artista 185
185_NA_engl 16.4.2004 15:07 Uhr Seite 1
030866.51.04_0401_a185_EN
185_NA_engl 16.4.2004 15:07 Uhr Seite 2
030866.51.04_0401_a185_EN
1Contents
Straight stitch, Zig-zag
Altered memory
Practical stitch seams
Sewing knits
Zippers
Long stitch function
Basting stitch
Blind hem
Elastic, cord
Bartack program
Buttonholes
Button sew-on program
Eyelets
Mending/darning
Decorative stitches
Quilt stitches
Decorative stitches combined with functions
Practical and decorative stitches in memory
16 direction stitching
4 direction stitching
Sideways motions stitches (outline motifs)
Balance
Index
2–5
6
7–11
12, 13
14
15
16
17
18, 19
20
21–28
29
30
31–34
35
36–38
39
40–42
43–44
45
46–48
49–50
51
185_NA_engl 16.4.2004 15:07 Uhr Seite 3
030866.51.04_0401_a185_EN
2 Straight stitch
Straight stitch
Straight stitch
· the machine is ready to sew as soon as it is turned on
· after the welcome screen (3 seconds), the machine
automatically goes to the practical stitch screen with
the pre-selected Straight Stitch highlighted
Screen
· suggests using reverse pattern presser foot #1C
· basic settings (length and width) for Straight Stitch
are preset at 2.25mm (length) and 0mm (width)
· basic settings as well as altered settings are always
visible on the screen
Alter the stitch length
· the stitch length can be altered while sewing
· turn the external stitch length knob to the right to
lengthen
· turn the external stitch length knob to the left to
shorten
Change the needle position
· push the external needle position buttons to change the
needle position so stitching can be placed exactly where
it is desired
· each push of the button moves the needle one position
in the direction of the symbol
< five positions to the left
> five positions to the right
· total of 11 positions, including center
· excellent for edgestitching, topstitching, and making
tucks
Securing with Quick Reverse
·press the quick reverse button and the machine sews in
reverse
·release the button and the machine sews forward
TIPS
Adjust the stitch length to suit the fabric:
· e.g. use a longer stitch length (approximately
3mm–4mm) with denim, shorter length(2mm–2.5mm)
with batiste
Adjust the stitch length to suit the thread:
· e.g. use a longer stitch length (approximately
3mm–5mm) when sewing with cordonnet thread for
top stitching
Activate needle stop down
·prevents the fabric slipping when you stop to adjust it
Straight Stitch No. 1
size and type suitable for the fabric selected
cotton or polyester
up (sewing position)
Reverse pattern foot No. 1C
Stitch:
Needle:
Thread:
Feed-dog:
Presser foot:
ABC
A straight stitch with length
of 2.25mm preset length
B straight stitch with altered
stitch length
C straight stitch with altered
needle positions
185_NA_engl 16.4.2004 15:07 Uhr Seite 4
030866.51.04_0401_a185_EN
Straight stitch 3
Securing stitch
Securing stitch
· for all fabrics
· secures beginning and end of seam
·reverse stitching is exactly on top of the seam,
preventing puckers
Stitch selection
· touch stitch No. 5
· quick reverse symbol will appear on-screen as a
reminder to use it when ending the seam
Screen
· suggests using reverse pattern presser foot No. 1
· basic settings (length and width) for Straight Stitch
are preset at 2.5mm (length) and 0mm (width)
Beginning the seam
· machine secures the seam automatically (5 stitches
forward, 5 stitches reverse)
· machine continues straight stitching
Ending the seam
· when coming to the end of the seam, press and release
the quick reverse button above the needle
· machine will secure the seam automatically (5 stitches
forward, 5 stitches reverse)
· machine stops automatically when securing is complete
TIP
Seaming
· quick and easy securing at beginning and
end of seam
Securing stitch No. 5
size and type suitable for the fabric selected
cotton or polyester
up (sewing position)
Reverse pattern foot No. 1C
Stitch:
Needle:
Thread:
Feed-dog:
Presser foot:
185_NA_engl 16.4.2004 15:07 Uhr Seite 5
030866.51.04_0401_a185_EN
4 Straight stitch
Narrow edge stitching
Needle position
· left for outer edge
· right for inner edge
Presser foot
· Blindstitch foot No. 5
Outer edge
· place finished or folded edge of fabric against the
guide of the foot
· select needle position at desired distance from the edge
Hem edges
· place edge of fold (inside upper edge of hem) against
the guide on the foot
· select a needle position that places the stitching along
the upper edge of the folded hem
Foot No. 5 – use any far left or far right needle position
Foot No. 10 – use any far left or right needle position
Wide edge stitching
Needle position
· any needle position can be used for this stitching
· different needle positions will place the stitching at
various distances from the edge of the fabric
Presser foot
·reverse pattern foot No. 1C
Guiding the fabric
Presser foot as a guide:
· align the edge of the presser foot with the finished or
folded edge of the fabric
Stitch plate as a guide:
· guide the folded edge along the markings on the
stitch plate for stitching 1cm–3cm from the edge
Quilting/Seam guide as a guide:
· insert the quilting/seam guide bar into the hole on the
back of the presser foot shank
· adjust as desired, measuring from the needle
· tighten the screw
· guide the finished or folded edge of the fabric along
the quilting/seam guide
· to sew parallel lines, guide the quilting/seam guide bar
along a previously sewn line of stitches
TIP
Edge stitching with quilting/seam guide
· eliminates tedious marking when sewing parallel lines
or grids
Edge stitching
5
5
Straight Stitch No. 1
size and type suitable for the fabric selected
cotton, polyester, or cordonnet (topstitching)
up (sewing position)
Reverse pattern foot No. 1C or Blindstitch Foot No. 5 or
Edgestitch Foot No.10/10C (optional accessory)
Stitch:
Needle:
Thread:
Feed-dog:
Presser foot:
185_NA_engl 16.4.2004 15:07 Uhr Seite 6
030866.51.04_0401_a185_EN
Zig-zag 5
Zig-zag applications
· for all fabric types
· for finishing raw edges
· for decorative work
Stitch selection
· touch zig-zag stich 2
Screen
· suggests using reverse pattern presser foot No.1C
· basic settings (length and width) for Zigzag Stitch
are preset at 1.5mm (length) and 3.5mm (width)
· basic settings as well as altered settings are always
visible on the screen
Altering the stitch width
· the stitch width can be altered while sewing
· turn the external stitch width knob to the right to
make the stitch wider
· turn the external stitch width knob to the left to
make the stitch more narrow
· move the knob in a smooth, gentle rotation for a
smooth tapering of the stitch
Alter the stitch length
· the stitch length can be altered while sewing
·turn the external stitch length knob to the right to
lengthen
·turn the external stitch length knob to the left to
shorten
· move the knob in a smooth, gentle rotation for a
smooth transition of the stitch length
Satin stitch
· short stitch length setting indicated by parallel lines
· filled-in stitch used for applique, cutwork, embroidery, and
other decorative applications
Oversewing edges
· good edge finish for most types of fabric
· guide edge of fabric into the center of the presser foot
· needle goes into fabric on one side and over the edge
into the air on the other
· do not select too wide a width or too long a stitch –
the edge should lie flat and not roll
TIPS
Oversewing edges with Zig-zag
· if edges roll, use the Vari-overlock stitch and foot
No.2A
Embroidery with satin stitch
· experiment with adjusting the stitch width for new
decorative effects
Zig-zag stitch
Zig-zag No. 2
size and type suitable for the fabric selected
cotton or polyester
up (sewing position)
Reverse pattern foot No. 1C
Stitch:
Needle:
Thread:
Feed-dog:
Presser foot:
A B C
A zigzag stitch with altered
stitch length
B zigzag stitch with altered
stitch width
C fabric edges finished with
zigzag stitch
185_NA_engl 16.4.2004 15:07 Uhr Seite 7
030866.51.04_0401_a185_EN
6
Temporary Altered Memory
· for all stitches and fabrics
· altered stitch length and width settings are saved
automatically
· sew a stitch (e.g. zig-zag stitch)
· select and sew a second stitch (e.g. straight stitch)
· when the first stitch (zig-zag), is recalled, all altered
settings remain
· particularly useful when alternating between two
applications, such as seaming and edge finishing
· the altered memory can hold as many stitches as
needed
Altering the basic settings
· select zig-zag stitch No. 2
· alter stitch width to 9mm
· alter stitch length to 1mm
· sew a line of the altered zigzag stitch
· select running stitch No. 4
· alter stitch width to 9mm
· alter stitch length to 1mm
· sew a line of the altered running stitch
Altered settings remain active
· select zig-zag stitch No. 2
· altered settings remain active
· sew a line of the altered zigzag stitch
· select running stitch No. 4
· altered settings remain active
· sew a line of the altered running stitch
Return to basic settings
· Method 1: press the external clr button
· Method 2: alter the stitch width and length manually
· Method 3: turn machine off – altered settings will not be
saved
Note:
The temporary altered memory can hold as many stitch altera-
tions as needed (these are stitch length, stitch width, Needle
position, Thread Tension and Balance)
TIPS
Altering stitch width and length
· the width and length of all stitches can be adjusted
to suit the fabric and type of sewing. Very convenient
when sewing a project which may require using the
same stitches repeatedly.
Changing Stitches
· alternating between sewing seams and finishing edges
is easy with altered settings for many stitches, which
remain altered once set
Temporary Altered Memory
Any selected stitch
size and type suitable for the fabric selected
cotton or polyester
up (sewing position)
Reverse pattern foot No. 1C
Stitch:
Needle:
Thread:
Feed-dog:
Presser foot:
Personal (altered) Memory
A B
A altered zigzag stitch
changed to altered running
stitch
B changed back to altered
zigzag stitch and then
changed again to altered
running stitch
185_NA_engl 16.4.2004 15:07 Uhr Seite 8
030866.51.04_0401_a185_EN
7Practical stitch seams
Open seams
Seams which are pressed open
· seam allowance width as wide as desired
· seam lies flat
· seam does not stretch
Suggested stitches:
· straight, narrow zigzag, super stretch, and triple
straight stitch
Application:
· primarily for woven fabrics
· works for most types of sewing projects, including
clothing, home accessories, and crafts
Closed seam (overlock seams)
Seams which cannot be pressed open
· sewn and finished in one operation
· narrow seam allowances
Suggested stitches:
· vari-overlock, double overlock, and jersey
Application:
· primarily for knits and jerseys
· excellent for knit clothing, lingerie, and bed linens
Flat joining seams
Seams where the edges are overlapped and then sewn
· stitching is on the seam allowances
Suggested stitch:
·stretch overlock
Application:
· particularly good for terry cloth
· also good for beachwear, leisure wear, and lingerie
Zig-zag stitch No. 2
approximately 1mm
approximately 0.5mm
universal, ballpoint, or stretch as needed
cotton or polyester
up (sewing position)
Reverse pattern foot No. 1C
Open seam applications
· stitch has more “give” than a straight stitch
· use for knits, outer wear, children’s knit clothes
· seam lies flat and is not bulky
· allows a garment to be let out
Practical stitch seams
TIP
Prevent stretching
· to prevent the stretching of the seam while being sewn,
reduce the presser foot pressure to suit the fabric
Zig-zag Seam
Stitch:
Stitch width:
Stitch length:
Needle:
Thread:
Feed-dog:
Presser foot:
185_NA_engl 16.4.2004 15:07 Uhr Seite 9
030866.51.04_0401_a185_EN
8
Triple Straight Stitch No. 6
80–90 universal or jeans
polyester
up (sewing position)
Reverse pattern foot No. 1C
Open seam
· durable seam for firm and densely woven fabrics such
as denim and corduroy
·reinforced seam for garment areas subject to hard wear
Super stretch No. 11 or Stretch No. 18
universal, ballpoint, or stretch as needed
cotton or polyester
up (sewing position)
Reverse pattern foot No. 1C
Open seam
· stretch seam for knit fabrics
· ideal for sports and leisure wear
· seam lies flat and is not bulky
TIPS
Knits and jersey
· use a new needle to prevent damaging the fabric fibers
Sewing stretch fabrics
· if necessary use a stretch ball point needle
(130/705H-S); needle point slides between the fibers
Prevent stretching
· to prevent the stretching of the seam while being sewn,
reduce the presser foot pressure to suit the fabric
Triple Straight Stitch seam
TIP
For heavy layers or very densely woven fabrics
A Jeans needle and Jeans Foot No. 8 will help when
stitching very heavy fabrics, such as denim or canvas
Stitch:
Needle:
Thread:
Feed-dog:
Presser foot:
Stretch/Super stretch seam
Stitch:
Needle:
Thread:
Feed-dog:
Presser foot:
Practical stitch seams
185_NA_engl 16.4.2004 15:07 Uhr Seite 10
030866.51.04_0401_a185_EN
9Practical stitch seams
TIPS
Knits and jersey
· use a new needle to prevent damaging the fabric fibers
Sewing stretch fabrics
· if necessary use a stretch needle (130/705H-S); the
point slides easily between the fibers
TIPS
Knits and jersey
· use a new needle to prevent damaging the fabric fibers
Sewing stretch fabrics
· if necessary use a stretch ball point needle (130/705H-S);
the point slides easily between the fibers
Vari-overlock seam
Vari-overlock No. 3
size and type suitable for the fabric selected
cotton or polyester
up (sewing position)
Overlock foot No. 2A
Closed seam
· stretchy seam in fine, soft knits such as silk jersey and
interlock
Sewing
· guide the raw edge along the pin on the overlock foot
· the stitch will form over the pin and over the edge of
the fabric
Double Overlock No.10 or Jersey Overlock No.20
size and type suitable for the fabric selected
cotton or polyester
up (sewing position)
Overlock foot No. 2A
Closed seam
· overlock seam in loose knits and cross seams in knits
and jerseys
Sewing
· guide the raw edge along the pin on the overlock foot
· the stitch will form over the pin and over the edge of
the fabric
Stitch:
Needle:
Thread:
Feed-dog:
Presser foot:
Double overlock seam/Jersey overlock seam
Stitch:
Needle:
Thread:
Feed-dog:
Presser foot:
2A
2A
185_NA_engl 16.4.2004 15:07 Uhr Seite 11
030866.51.04_0401_a185_EN
10
Stretch Overlock No. 13 or Reinforced Overlock No. 19
universal, ballpoint, or stretch as needed
cotton or polyester
up (sewing position)
Reverse pattern foot No. 1C
Closed seam
· overlock seam in coarse or loose knits
Sewing
· sew stretch overlock along the fabric edge
· the stitch should go over the edge of the fabric on the
right swing of the needle
Stretch Overlock No. 13
universal, ballpoint, or stretch as needed
cotton or polyester
up (sewing position)
Reverse pattern foot No. 1C
Flat joining seam
· fabric edges are overlapped and the stitch is placed on
the seam allowance
·produces a very flat, durable seam
· ideal for fluffy, thick materials such as terry cloth, felt
and leather
Sewing
· sew stretch overlock along the fabric edge
· the stitch should go over the edge of the top layer of
fabric on the right swing of the needle
TIPS
Fabric and thread
· use a matching thread colour, for less visibility in fluffy
fabrics
Thick seam
· particularly suitable for fabrics in which a normal
straight stitch seam would stretch open
TIP
Prevent stretching
· to prevent the stretching of the seam while being sewn,
reduce the presser foot pressure to suit the fabric
Stretch overlock seam/Reinforced overlock seam
Stitch:
Needle:
Thread:
Feed-dog:
Presser foot:
Stitch:
Needle:
Thread:
Feed-dog:
Presser foot:
Flat joining seam
Practical stitch seams
185_NA_engl 16.4.2004 15:07 Uhr Seite 12
030866.51.04_0401_a185_EN
11Practical stitch hems
Preparation
· fold and press hem; baste if desired
Sewing
· sew hem at desired depth (right side)
· trim excess fabric (wrong side)
Jersey stitch No. 14
universal, ballpoint, or stretch as needed
cotton or polyester
up (sewing position)
Reverse pattern foot No. 1C
Visible stretch hem
· for all types of cotton, wool, synthetic and mixed fiber
jerseys
Triple Zig-zag No. 7
2.5mm – 9mm depending on fabric
basic setting
universal or jeans
cotton or polyester
up (sewing position)
Reverse pattern foot No. 1C
Strong visible seam
· for firm, densely woven fabrics, particularly good for
denim and canvas
TIPS
Knits and jersey
· use a new needle to prevent damaging the loops of
the knit fabric
Sewing stretch fabrics
· if necessary, use a stretch needle (130/705H-S); the
point slides easily between the fibers
TIPS
Hems on fabrics which may ravel
· finish the raw edge of the hem;do not trim them after
sewing
Sewing firm, hard fabrics
· use a jeans needle for better penetration
Hems with practical stitches
Visible hem with Jersey stitch
Stitch:
Needle:
Thread:
Feed-dog:
Presser foot:
Stitch:
Stitch width:
Stitch length:
Needle:
Thread:
Feed-dog:
Presser foot:
Visible hem with Triple Zig-zag
185_NA_engl 16.4.2004 15:07 Uhr Seite 13
030866.51.04_0401_a185_EN
12
Sewing knits
TIPS
Needle stop down
· needle stays in fabric when pivoting around curves
(neck edges and armholes)
Presser foot pressure
·reduce pressure if hem stretches
Honeycomb stitch No. 8
universal, ballpoint, or stretch as needed
cotton or polyester
up (sewing position)
Reverse pattern foot No. 1C
Honeycomb stitch edges
· for all cotton, wool, synthetic and mixed fiber knits
Preparation
· turn the raw edge under by 1 cm (
3
/
8
”); press and
baste if desired
Sewing
·sew from the right side
· trim excess fabric from the wrong side
Balance/corrections
· Stitch is too open – make the stitch shorter by touching the
“up” (↑) balance arrow several times
· Stitch is overlapping – make the stitch longer by touching
the “down” (↓) balance arrow several times
Honeycomb stitch edges
Stitch:
Needle:
Thread:
Feed-dog:
Presser foot:
Important tips for sewing knit fabrics
Sewing knits
Start with a new needle
· blunt needles can damage knits
Use a stretch needle (130/705 H-S) if necessary
· the needle point slides easily between the fibers
Use a fine sewing thread
· coarse threads can damage knits and cause holes when
the garment is washed
When basting, use a darning thread
· very lightweight (80 weight) darning thread is easier to
remove once the seam is complete
Sew a test, when necessary
· the elasticity of knit fabrics varies greatly
· adjust basic settings to suit the fabric, the seam
should be as stretchy as the fabric
· for greater elasticity:
· use a shorter stitch length
· use a wider stitch width
(only one of these adjustments may be necessary)
Presser foot pressure
· soft, loose knits can wave when sewn:
reduce the pressure until the seam lies flat the machine
must still feed the fabric properly
185_NA_engl 16.4.2004 15:07 Uhr Seite 14
030866.51.04_0401_a185_EN
13Sewing knits
TIP
Nadelstopp unten
· grosse Hilfe beim Nachfassen des Bündchens um
Rundungen (Hals/Armloch)
Vari-overlock No. 3
size and type suitable for the fabric selected
cotton or polyester
up (sewing position)
Overlock foot No. 2A
Ribbing with overlock seam
· for all fine cotton, synthetic and mixed fiber knits
Preparation
· fold ribbing in half
· pin and baste to opening, front edge to outside
Sewing
· sew Vari-overlock over the raw edge
· guide the raw edge along the pin of the foot
· the stitch will form over the pin and over the edge of
the fabric
Ribbing with overlock seam
Stitch:
Needle:
Thread:
Feed-dog:
Presser foot:
2A
185_NA_engl 16.4.2004 15:07 Uhr Seite 15
030866.51.04_0401_a185_EN
14
Straight stitch No. 1
size and type suitable for the type of fabric selected
cotton or polyester
up (sewing position)
Zipper foot No. 4
far right or far left
Preparation:
· baste or pin zipper in place
· fabric edges should meet over the center of the zipper
Sewing
· sew both sides of zipper from bottom to top
· needle position should be fully to the right on one side
and and fully to the left on the other
· edge of presser foot runs next to zipper teeth
· position the foot so the needle stitches along the edge
of the zipper teeth
Zippers
TIPS
To sew around the zipper pull
· close the zipper and sew up to about 5 cm (2”) away
from the pull
· stop with the needle down in the fabric, raise the
presser foot. Open the zipper, pulling the tab below the
needle; lower the foot and continue to sew
Starting to sew
· hold the thread firmly when starting to sew
· pull the fabric gently behind the needle for a few
stitches
Dense fabric
· for even stitch formation, use a 90 or 100 needle
Stitch:
Needle:
Thread:
Feed-dog:
Presser foot:
Needle position:
4
Zippers
185_NA_engl 16.4.2004 15:07 Uhr Seite 16
030866.51.04_0401_a185_EN
15Long stitch
Straight stitch No. 1 or Triple Straight Stitch No. 6
size and type suitable for the fabric selected
cotton or polyester
3.5mm – 5mm
up (sewing position)
Reverse pattern foot No. 1C
Long stitch
Long stitch
· for all work where a longer stitch is desired
· for topstitching
Long stitch function
Stitch:
Needle:
Thread:
Stitch length:
Feed-dog:
Presser foot:
Function:
TIPS
Decorative top stitching
· use cordonnet (topstitching) thread and a 100–110
needle with the straight stitch
Basting
· long stitch can also be used to baste fine fabrics
This function works with the straight stitch to produce a
longer than usual stitch.
The machine sews every second stitch when the Long
stitch function is activated. The longest stitch possible is
10 mm when the stitch length is set at 5mm.
For decorative top stitching, the Long stitch function can
be combined with Triple Straight stitch.
185_NA_engl 16.4.2004 15:07 Uhr Seite 17
030866.51.04_0401_a185_EN
16
Basting stitch
TIPS
Securing a basted seam
· to secure basting stitches, sew a few normal length
straight stitches at the beginning and end of the seam
Basting
· use a fine darning thread; it is easier to remove after
the seam has been sewn
Basting stitch No. 21
size and type suitable for the fabric selected
cotton or polyester
3.5mm – 5mm
up (sewing position)
Reverse pattern foot No. 1C
Basting stitch
· for all work where a very long stitch is desired
· quick and easy basting of seams, hems, etc.
· easy to remove
Stitch:
Needle:
Thread:
Stitch length:
Feed-dog:
Presser foot:
This feature is a stitch rather than a function (such as the
long stitch). When this stitch (No. 21) is selected, the
machine stitches a straight stitch, sewing every fourth
one. The longest stitch possible is 20 mm when the stitch
length is set at 5mm.
Basting stitch
185_NA_engl 16.4.2004 15:07 Uhr Seite 18
030866.51.04_0401_a185_EN
17Blind hem
TIP
Fine stitch width adjustment
· guide the raw edge along the guide on the foot to keep
the stitch depth even
Blindstitch No. 9
size and type suitable for the fabric selected
cotton, polyester, or silk
up (sewing position)
Blindstitch foot No. 5
Blind hem
· for invisible hems in medium to heavy cotton, wool and
mixed fiber fabrics
Preparation
· finish the raw edges as desired
· fold the hem and baste or pin in place
· fold the garment back over the right side of the fabric
to expose the finished lower edge
· place the work under the presser foot (see drawing)
with the guide positioned against the folded back
fabric
Sewing
· the needle should just pierce the edge of the fold
· adjust the stitch width to suit the fabric
· after sewing about 10 cm (4”), check both sides of
fabric and adjust the stitch width if necessary
Blind hem
5
Stitch:
Needle:
Thread:
Feed-dog:
Presser foot:
right side of fabric
wrong side of fabric
wrong side of fabric
185_NA_engl 16.4.2004 15:07 Uhr Seite 19
030866.51.04_0401_a185_EN
18
Universal stitch No. 15
depends on width of elastic
type and size to suit the fabric selected
cotton or polyester
up (sewing position)
Reverse pattern foot No. 1C
or Embroidery foot No. 6 (optional accessory)
Sewing on elastic
· for gathering long lengths of fabric, frills and flounces
in fine fabrics
· works well for gathered sleeve edges and neck
openings
Preparation
· cut elastic to length required
Sewing
· oversew the elastic, adjusting the stitch width to be
slightly wider than the elastic
· needle must not pierce the elastic
· after sewing,adjust the gathers evenly
Sewing on narrow elastic with Universal stitch
Secure the beginning and end of elastic
· sew a few straight stitches backward and forward to secure the elastic
Quick hem finish
· for children’s or doll clothing
· sew sleeve edges with elastic before sewing seams
Securing beginning and end
· sew a few stitches with the feed-dog lowered
Presser foot pressure
· increase the foot pressure, if necessary, for better
feeding of the fabric and cord
Gathering stitch No. 12
size and type to suit the fabric selected
cotton or polyester
up (sewing position)
Buttonhole foot No. 3C
Shirring elastic/cord
· for gathering long lengths of fabric
Preparation
· cut shirring elastic or cord double the length of the edge
· fold in half lengthways
· hook over the center toe on the buttonhole foot
· take both ends of the cord under the foot to the back
Sewing
· sew a few stitches
· lift the elastic or cord at the front and pull towards you
· leave ends behind the presser foot
· oversew cord without stitching into it
· after sewing, pull the cord to gather the fabric
· stretch elastic while sewing; the more it is stretched, the
tighter the gathers
Sewing on shirring elastic/cord with Gathering stitch
Stitch:
Needle:
Thread:
Feed-dog:
Presser foot:
Elastic, cord
Stitch:
Stitch width:
Needle:
Thread:
Feed-dog:
Presser foot:
TIPS
TIPS
185_NA_engl 16.4.2004 15:07 Uhr Seite 20
030866.51.04_0401_a185_EN
19Elastic, cord
TIP
Preventing elastic from stretching too much
· avoid over-stretching the elastic; adjust the presser
foot pressure to suit the fabric.
Running stitch No. 4 or Sewn-out Zig-zag No. 16 or
Lycra stitch No. 17
adjust to suit elastic
size and type to suit the fabric selected
cotton or polyester
up (sewing position)
Reverse pattern foot No. 1C
Wide elastic
· for edges on sportswear and lingerie
Preparation
· cut elastic to length required
· divide fabric edge and elastic into 4 equal sections
and mark
· pin elastic to raw edge, matching up markings
Sewing
·stretch the elastic to fit the raw edge while sewing
· trim excess fabric close to the stitching
Sewing on wide elastic
Stitch:
Stitch length:
Needle:
Thread:
Feed-dog:
Presser foot:
185_NA_engl 16.4.2004 15:07 Uhr Seite 21
030866.51.04_0401_a185_EN
20 Bar tack program
Bartack program No. 24 or Buttonhole bartack No. 25
size and type to suit the fabric selected
cotton, polyester, or rayon
up (sewing position)
Reverse pattern foot No. 1C
Bartack program
· for reinforcing seams subject to heavy wear such as
those on pockets, jackets, jeans and overalls
· use for attaching ribbons to a quilt for tying
Buttonhole bartack
· for reinforcing buttonhole bartacks
Sewing
· the machine starts top left with the bartack program
· the machine stops automatically at the end of the
program
Bartack program
Stitch:
Needle:
Thread:
Feed-dog:
Presser foot:
Tip
Decorative bartacks
Increase the stitch length and sew the bartack program
with decorative thread as a decorative element; or
combine two together at right angles to each other as
decoration.
Shorten zipper
A zipper that is too long can be trimmed and reinforced
by using the Bartack program No. 25.
Fly Stitch
Stitch:
Needle:
Thread:
Feed-dog:
Presser foot:
Fly stitch No. 26
size and type to suit the fabric selected
cotton, decorative or polyester
up (sewing position)
Reverse pattern foot No. 1C or Sideways motion foot
No. 40C
Fly stitch
The fly stitch is used as reinforcement at the end of
seams, e.g. pocket edges or slits
· for mediumweight to thick fabric
Sewing
· place presser foot No. 1C in the middle of the seam at
the end of the slit or the pocket edge
· the fly stitch is automatically sewn from bottom to top
(in reverse)
· the sewing computer stops automatically at the end
TIPS
Hand-stitched effect
·To get a hand-stitched effect the fly stitch can be sewn
with a heavier thread.
· The fly stitch can also be used as a decorative effect.
185_NA_engl 16.4.2004 15:07 Uhr Seite 22
030866.51.04_0401_a185_EN
21Buttonholes
Thread tension
· the tension is set automatically when a buttonhole
is selected
· the upper tension is slightly looser than normal
· this gives a slightly rounded appearance to the beads,
making the buttonhole more attractive
Manual buttonholes
· stitched using Buttonhole foot 3C
· the buttonhole length of manually stitched buttonholes
must be marked on the fabric in the appropriate
position
Automatic buttonholes
· stitched using Automatic buttonhole foot 3A
· mark the length of the first buttonhole
· after sewing the first buttonhole, the length for all
subsequent buttonholes is automatically programmed
· mark the starting point of all subsequent buttonholes
· Buttonhole length = buttonhole opening in mm
Test sewing
· always sew a test on the fabric(s) you will use with the
same interlining, interfacing, and stabilizers
· select the same buttonhole type
· sew the buttonhole in the same direction on the
fabric (with or against the grain)
Corrections
To adjust the bead width:
· alter the stitch width
Altering the stitch length:
· any alterations to the stitch length affect both beads
(making them more or less dense)
· always stitch a new sample to reprogram the buttonhole after
any changes are made to the stitch length
Balance for automatic buttonholes
· any balance alterations affect both beads
· the keyhole or eye is balanced as follows:
· sew straight stitches until the sewing computer
changes to the keyhole or eye, then stop the sewing
computer
· touch "Balance”
if the keyhole is distorted to the right (picture A)
· use the "down” arrow to correct it
if the keyhole is distorted to the left (picture B)
· use the "up” arrow to correct it
· touch "ok” and complete buttonhole
Balance for manual standard buttonholes
· any balance alterations affect both beads
Important information on buttonholes
A
B
185_NA_engl 16.4.2004 15:07 Uhr Seite 23
030866.51.04_0401_a185_EN
22 Buttonholes
Balance for keyhole and round buttonholes
· any balance alterations affect both beads differently
(see picture for stitch counter buttonhole)
· the keyhole or eye is balanced as follows:
if keyhole is distorted to the right (picture A):
· use the "up” arrow to correct it
if keyhole is distorted to the left (picture B):
· use the "down" arrow to correct it
Balance for stitch counter buttonholes
· any balance alterations affect the first (left) bead:
Bead too dense – if the first bead looks like
A, use the “down” arrow to correct it
Bead not dense enough – if the first bead looks like B,
use the “up” arrow to correct it
· always stitch a new sample to reprogram the buttonhole after
any changes are made to the balance
Clear balance
·press the external clr button
Corded Buttonhole
· gimp cord reinforces buttonholes and enhances their
appearance
· the loop of the cord should be at the end of the
buttonhole most subject to wear or where the button is
sewn on
· position the work accordingly
· gimp cord is particularly recommended for standard
and stretch buttonholes
Suitable cords:
· Perle yarn No. 8
· strong hand sewing thread
· fine crochet yarn
· gimp cord
Hooking the cord onto presser foot No. 3C
· insert the needle at the beginning of the buttonhole
· raise the presser foot
· hook the cord over the center toe of the foot
· place both ends of the cord in the grooves on the sole
of the foot and pull them to the back
· lower the presser foot
Sewing
· sew the buttonhole in the usual manner
· do not hold the cord tightly
· the buttonhole will form over the cord, covering it
Securing the cord
· pull the cord through the buttonhole until the loop
disappears into the end of it
· pull the ends of the cord through to back of the fabric
· knot or secure with stitches
AB
185_NA_engl 16.4.2004 15:07 Uhr Seite 24
030866.51.04_0401_a185_EN
23Buttonholes
Hooking the cord in the automatic buttonhole foot No. 3A
· insert the needle at the beginning of the buttonhole
· raise the presser foot
· guide the cord under the foot to the right
· hook the cord over the pin at the back of the foot
· bring the cords to the front of the foot
· pull each end into one of the notches at the front of
the foot
Sewing
· sew the buttonhole in the usual manner
· do not hold the cord
· the buttonhole will form over the cord, covering it
Securing the cord
· pull the cord through the buttonhole until the loop
disappears into the end of it
· pull the ends of the cord through to back of the fabric
· knot or secure with stitches
Cutting buttonholes open
· using the seam ripper, cut from the ends towards the
middle
· in order not to cut the ends of short buttonhole by
mistake, place a straight pin at the end of the button-
hole for additional security.
Buttonhole cutter and block (special accessory)
· place the fabric on a piece of wood
· place the cutter in the center of the buttonhole
·press the handle of the cutter to open the
buttonhole
3A
3A
185_NA_engl 16.4.2004 15:07 Uhr Seite 25
030866.51.04_0401_a185_EN
24
Straight stitch buttonholes No. 59
size and type suitable for the fabric selected
cotton or polyester
up (sewing position)
Buttonhole foot No. 3C or Automatic Buttonhole Foot No. 3A
Automatic program with Automatic buttonhole foot No. 3A
· if using Automatic buttonhole foot No. 3A, the sensor on
the foot will automatically register the length of the
buttonhole so it can be duplicated
Sewing the automatic buttonhole program
· sew the first line of straight stitches forward until the
desired length is reached
·press and release the quick reverse button
· auto appears = length is programmed
· machine completes the buttonhole program automatically
· all subsequent buttonholes will be stitched to the same
length (without pressing the quick reverse button)
· the distance between the stitched lines can be adjusted
with the stitch width
Stitch counter program with buttonhole foot No. 3C
· select function presser foot 3C for stitch counter
buttonholes
· Buttonhole foot no. 3C will register the number of
stitches in the buttonhole
Sewing the stitch counter buttonhole program
· sew the first bead, stop stitching at the desired length
·press and release the quick reverse button
· continue sewing; the machine will stitch the end of the
buttonhole and then the second bead in reverse
· stop stitching when the needle reaches the first stitch
·press and release the quick reverse button
· machine sews the horizontal bar and securing stitches
· machine stops automatically
· auto appears on the screen
· each subsequent stitched buttonhole will be sewn to
the same length as the programmed buttonhole
Straight stitch buttonholes
Stitch:
Needle:
Thread:
Feed-dog:
Presser foot:
3A
Straight stitch buttonholes are useful as a foundation for
satin stitched buttonholes on soft and loosely woven
fabrics that fray easily. The buttonhole beads and bartacks
of the second (satin stitched) buttonhole will cover the
straight stitching.
They are also good for stitching bound buttonholes and
reinforcing buttonhole openings on leather, vinyl, and felt.
Buttonholes
185_NA_engl 16.4.2004 15:07 Uhr Seite 26
030866.51.04_0401_a185_EN
25Buttonholes
Buttonhole (all types)
size and type suitable for the fabric selected
cotton or polyester
up (sewing position)
Automatic buttonhole foot No. 3A
Automatic buttonhole
· the lens on automatic buttonhole foot No. 3A
automatically registers the length of the buttonhole for
exact duplication
· buttonholes from 4–29 mm can be sewn
Sew the first bead
· the stitching sequence is displayed on the screen (to
the right of the presser foot symbol)
· sew the first bead forward, stopping at the desired
length
Program the buttonhole
·press and release the quick reverse button
· auto appears on the screen to indicate that the
buttonhole length is programmed
· continue sewing; the machine completes the
buttonhole and stops automatically
Auto buttonhole
· machine stops in position to begin the next buttonhole
·reposition the fabric and sew; all subsequent
buttonholes will be sewn automatically to the same
length (without pressing the quick reverse button)
Important:
· if you make a mistake, press the Pattern Begin function
· the machine reverts to the beginning of the buttonhole
Automatic buttonholes (all types)
Stitch:
Needle:
Thread:
Feed-dog:
Presser foot:
Both beads are sewn in the same direction.
Buttonhole length = buttonhole opening in mm
Stretch buttonholes are particularly effective on all knit
fabrics because the double overlock stitch used for the
beads stretch with the fabric while keeping its shape.
Note: The automatic buttonhole foot 3A must lie
perfectly flat on the fabric. If the foot lies on a seam,
the length cannot be measured accurately.
3A
TIPS
Exact duplicates
· the auto function ensures
that each buttonhole will
be exactly the same
length as the previous
one
Marking
· mark only the beginning
of the buttonholes – a
real time saver!
Sewing speed
· sew at moderate speed
for best results
· sew all buttonholes at
the same speed for a
consistent bead density
185_NA_engl 16.4.2004 15:07 Uhr Seite 27
030866.51.04_0401_a185_EN
26
Round buttonholes 54+55, and keyhole
buttonholes 56–58 and Handlook buttonhole #63
size and type suitable for the fabric selected
cotton or polyester
up (sewing position)
Automatic buttonhole foot No. 3A
Automatic buttonhole
· the lens on automatic buttonhole foot No. 3A
automatically registers the length of the buttonhole for
exact duplication
· buttonholes from 4–29 mm can be sewn
· for keyhole buttonholes #56, 57, 58 – from 4–24 mm
for rounded and hand-look buttonholes #54, 55, 63 –
from 4–27 mm
Sew the buttonhole
· the stitching sequence is displayed on the screen (to
the right of the presser foot symbol)
· sew straight stitches forward, stopping at the desired
length
Program the buttonhole
·press and release the quick reverse button
· auto appears on the screen to indicate that the
buttonhole length is programmed
· continue sewing; the machine completes the
buttonhole and stops automatically
Auto buttonhole
· machine stops in position to begin the next buttonhole
·reposition the fabric and sew; all subsequent
buttonholes will be sewn automatically to the same
length (without pressing the quick reverse button)
Important:
· if you make a mistake, press the Pattern Begin function
· the machine reverts to the beginning of the buttonhole
Automatic round, keyhole and hand-look buttonholes
Stitch:
Needle:
Thread:
Feed-dog:
Presser foot:
Both beads are sewn in the same direction.
Buttonhole length = buttonhole opening in mm
TIPS
Exact duplicates
· the auto function ensures that each buttonhole will be exactly the same length
as the previous one
Marking
· mark only the beginning of the buttonholes – a real time saver!
Double sewn keyhole buttonholes
· keyhole buttonholes can be sewn twice on thick fabrics
· after sewing the first buttonhole, do not move the work
· simply tap the foot control once to begin sewing again
Buttonholes
3A
185_NA_engl 16.4.2004 15:07 Uhr Seite 28
030866.51.04_0401_a185_EN
27
Buttonholes (all types)
size and type suitable for the fabric selected
cotton or polyester
up (sewing position)
Buttonhole foot No. 3C
Stitch counter buttonholes
· Select the stitch counter buttonhole function
Length of first bead
· sew the first bead, stopping at the desired length
·press and release the quick reverse button
Bartack, second bead
· bottom bartack and second bead are sewn in reverse
· stop machine at the first stitch
·press and release the quick reverse button
Bartack, securing stitches
· machine sews the top bartack and securing stitches
· machine stops automatically
· auto appears on the screen
· the buttonhole is programmed and saved
· each subsequent buttonhole will be sewn identically
Corrections
·reprogram the buttonhole if any alterations to the
stitch width, length, or balance have been made
Programmed buttonhole on a different fabric
· different fabrics and interfacings can affect the look of
a stitch counter buttonhole
· if you are using a new material, program the
buttonhole again
Stitch counter buttonholes for all buttonhole types
(can not be saved in memory)
Stitch:
Needle:
Thread:
Feed-dog:
Presser foot:
The first (left) bead is sewn forwards, the second (right)
bead is sewn in reverse.
TIPS
More buttonholes with presser foot No. 3C
· ideal for buttonholes which are difficult to sew with the larger foot of Automatic
buttonhole foot No.3A
Beautiful buttonholes
· keep the speed consistent for beads of equal density
· sew at a moderate speed for best results
Marking
· mark only the beginning of the buttonholes – a real time saver!
Buttonholes
185_NA_engl 16.4.2004 15:07 Uhr Seite 29
030866.51.04_0401_a185_EN
28 Buttonholes
any buttonhole
size and type suitable for the fabric selected
cotton or polyester
up (sewing position)
Buttonhole foot No. 3C
Open the program
· select the type of buttonhole desired
(stitches Nr. 51-59, 63)
· select the manual buttonhole function from the toolbar
Step symbols
· the step sequence is shown on the screen:
· standard buttonhole has 6 steps
· round buttonhole has 4 steps
· keyhole buttonhole has 4 steps
· the arrow in the circle is on “0” when the buttonhole
is first selected
Sewing a 4 or 6 step buttonhole
· touch 1 on the screen and sew the first bead
· stop the machine at the desired length
· touch 2, sew
· continue in this manner until the buttonhole is
complete
Manual 4/6-step buttonholes (all types)
Stitch:
Needle:
Thread:
Feed-dog:
Presser foot:
Sewing buttonholes manually is ideal if you only need to
sew one; also for repairing existing buttonholes.
The number of steps depends on the type of buttonhole.
A manually sewn buttonhole cannot be saved.
TIP
Repairing buttonholes
· use the steps which are necessary to repair the worn
sections, omitting or bypassing the unneeded ones
185_NA_engl 16.4.2004 15:07 Uhr Seite 30
030866.51.04_0401_a185_EN
29Button sewing-on program
Button sew-on program No. 60
depends on the distance between the holes
size and type suitable for the fabric selected
cotton or polyester
down (darning position)
Button sew-on foot No. 18 (optional accessory)
Button sew-on program
· sews buttons with 2 and 4 holes
· the shank (thread length between button and fabric)
can be made shorter or longer as required
· buttons being sewn on for decorative purposes only
can be stitched without forming a thread shank
2-hole button
· select Button Sew-on program
· check distances between holes with the handwheel
· adjust stitch width if necessary
· hold the threads when starting to sew
· sew; machine stops automatically when program is
completed
· machine is automatically ready for the next button
Beginning and ending threads
·the threads are secured and can be trimmed
For secure results:
· cut the upper thread close to the button
· pull both bobbin threads until the upper thread is
visible on the wrong side
· trim bobbin thread (knot if desired)
4-hole button
· sew the front holes
· carefully move the button forward
· sew the back holes
Button sewing-on program
Stitch:
Stitch width:
Needle:
Thread:
Feed-dog:
Presser foot:
18
TIPS
Sewing on buttons by machine
·a real time saver, especially when several of the same
type buttons must be sewn on, e.g. shirts, blouses, etc.
Shortening zippers
·a zipper which is too long can be secured simply and
quickly using the button sew-on program
18
185_NA_engl 16.4.2004 15:07 Uhr Seite 31
030866.51.04_0401_a185_EN
30
TIPS
Eyelets
· ideal for eyes on soft toys, dolls and puppets
Decorative eyelets
· use decorative thread to introduce an attractive
element when combined with other embroidery or
decorative stitches
Eyelets
Zigzag Eyelets
Zig-zag Eyelet No. 61
size and type suitable for the fabric selected
cotton, polyester, or rayon
up (sewing position)
Reverse pattern foot No. 1C
Zig-zag Eyelet
· ideal opening for cords and narrow ribbons
· attractive decorative elements for clothing, crafts, etc.
· cannot be programmed into memory
Sewing eyelets
· select eyelet stitch No. 61
· position fabric under the presser foot and sew
· machine stops automatically when finished
· machine is automatically ready for the next eyelet
Punching eyelets
· use an awl or punch to cut open the eyelet
Stitch:
Needle:
Thread:
Feed-dog:
Presser foot:
Straight Stitch Eyelets
Straight Stitch Eyelets No. 62
size and type suitable for the fabric selected
cotton, polyester, or rayon
up (sewing position)
Reverse pattern foot No. 1C
Straight Stitch Eyelet
· ideal opening for cords and narrow ribbons
· attractive decorative elements for clothing, crafts, etc.
· cannot be programmed into memory
Sewing eyelets
· select eyelet stitch No. 62
· position fabric under the presser foot and sew
· machine stops automatically when finished
· machine is automatically ready for the next eyelet
Punching eyelets
· use an awl or punch to cut open the eyelet
Stitch:
Needle:
Thread:
Feed-dog:
Presser foot:
185_NA_engl 16.4.2004 15:07 Uhr Seite 32
030866.51.04_0401_a185_EN
31Darning, mending
Elastic Edges
TIP
Prevent fabrics stretching
·To prevent the fabric from stretching as it is sewn,
reduce the presser foot pressure to suit the fabric
Zig-zag stitch No. 2
approximately 5mm
1mm – 1.5mm
size and type suitable for the fabric selected
cotton or polyester
up (sewing position)
Reverse pattern foot No. 1C
Elastic edges
· use on knit garments to re-form out-of-shape edges
Sewing
· guide double length of shirring elastic along the edge
of the fabric, stretching the elastic slightly
· oversew the elastic with a zig-zag stitch
· do not sew through the elastic, only over it
· adjust elastic after sewing is complete to regain the
correct shape and size
Stitch:
Stitch width:
Stitch length:
Needle:
Thread:
Feed-dog:
Presser foot:
185_NA_engl 16.4.2004 15:07 Uhr Seite 33
030866.51.04_0401_a185_EN
32 Darning, mending
Jersey stitch No. 14
size and type suitable for the fabric selected
lightweight darning thread
up (sewing position)
Reverse pattern foot No. 1C
Covering worn or damaged areas
· particularly suitable for stretchy fabrics, lingerie
Preparation
· do not cut damaged area
·round off the edges of the patch to retain flexibility
· pin and baste to right side
Sewing
· place patch over worn area
· sew over edge
· sew a second row inside the first if desired)
· cut away damaged area
Honeycomb stitch No. 8 or Running stitch No. 4
size and type suitable for the fabric selected
lightweight darning thread
up (sewing position)
Reverse pattern foot No. 1C
Reinforcing edges
· good for work clothes, table linen, towels, etc.
· use a cord to match the color of the fabric
Suitable cords
· perle yarn
· fine crochet yarn
· strong hand-sewing thread
· gimp
Sewing
· oversew edges with Honeycomb or Running stitch
· oversew a cord along the edge for added reinforcement
· if necessary, sew a second row somewhat in from the
edge
TIPS
Knits
· use a new needle to prevent damage of the fabric loops
Sewing stretch fabrics
· if necessary use a stretch needle (130/705 H-S); point
slides easily between the fibers
Prevent stretching
· to prevent the stretching of the seam while being sewn,
reduce the presser foot pressure to suit the fabric
Stitch:
Needle:
Thread:
Feed-dog:
Presser foot:
Reinforced edges on woven fabrics
Stitch:
Needle:
Thread:
Feed-dog:
Presser foot:
Patches on knits and jersey
185_NA_engl 16.4.2004 15:07 Uhr Seite 34
030866.51.04_0401_a185_EN
33
Darning
Simple Darning Program No. 22 or Reinforced Darning
Program No. 23
size and type suitable for the fabric selected
lightweight darning thread
up (sewing position)
Automatic buttonhole foot No. 3A
Reverse pattern foot No. 1C
Preparation
· stretch fine fabrics into a darning or embroidery ring to
prevent distortion
Simple Darning Program No. 22
·replaces threads along the lengthwise grain in all fabrics
· use Reverse pattern foot No. 1C
· touch the Stitch counter function (foot 3) on the
function bar
· sew the first row
· on this machine, there is NO NEED to press the Quick
reverse a second time
· sew the second row
·press and release the quick reverse button; this programs
the second length
· continue sewing; the machine stops automatically
Corrections
· if the darning becomes distorted, correct with the Balance
function (see page 50–51)
Reinforced Darning Program No, 23
·replaces threads along the lengthwise and crosswise
grains in all fabrics
· use Automatic buttonhole foot No. 3A
· insert the needle in the top left of the worn area
· sew the first vertical row
·press and release the quick reverse button at the desired
length; this programs the length needed
· continue sewing; the machine stops automatically when
finished
Large areas
·reposition the work under the foot to continue covering
the worn area
· begin sewing;the program will repeat (length is saved)
Automatic darning
Quick darning of holes or worn areas
TIPS
Reinforced darning
· place a piece of gauze under the worn area before
darning
Large areas
· increase the darning area lengthwise and crosswise by
moving the work under the foot
Stitch:
Needle:
Thread:
Feed-dog:
Presser foot:
185_NA_engl 16.4.2004 15:07 Uhr Seite 35
030866.51.04_0401_a185_EN
34 Darning
Straight stitch No. 1
size and type suitable for the fabric selected
lightweight darning thread
down (darning position)
Darning foot No. 9 (optional accessory)
Darning holes or worn areas
·replaces threads with the lengthwise and the crosswise
grains in all fabrics
Preparation
· stretch fabric into darning ring (optional accessory) to
prevent distortion
· use of the slide-on sewing table is recommended
Sewing
· move the darning ring smoothly and without using
pressure
· work from left to right
Stitch over the hole
· sew the first rows to cover the hole (not too close)
·turn work by a quarter turn – 90°
Cover the first rows
· sew over the first rows – not too close for a soft finish
·turn work by a half turn –180°
Complete darning
· loosely and in same direction as 2nd rows
Method for tubular items
· first step in a horizontal direction
· second and third steps in lengthways direction
When you have mastered the technique
· work the rows in irregular lengths so that the turns are
“lost” in the fabric
Stitching hints
· move the hoop as if writing the letters “L” or “M”
· when changing direction, move in curves, avoiding
points
· this prevents holes and thread breakage
· do not sew in circles; these do not mimic the fabric
threads
Manual darning
TIPS
Thread breaks
· if thread breakage is a problem, it could be that the
ring is not being moved smoothly
Poor stitch formation
· if the thread is lying on top of the fabric, the ring is
being moved too quickly
· if there are knots on the underside of the fabric, the
ring is being moved too slowly
Stitch:
Needle:
Thread:
Feed-dog:
Presser foot:
185_NA_engl 16.4.2004 15:07 Uhr Seite 36
030866.51.04_0401_a185_EN
35
Decorative stitches
9 mm wide decorative stitches
embroidery needle in a size suitable for the fabric selected
cotton or rayon embroidery
up (sewing position)
Reverse Pattern foot No. 1C or
Open Embroidery Foot No. 20C
Embroidery foot No. 6 (optional)
Clear foot No. 34/34C (optional)
Decorative stitches
· for all fabrics
· for embellishing and decorative work
Stitch selection
·press the external menu button for Decorative stitches
· select the desired stitch group from the screen (groups
100, 300, 400, 600, 700, and 900 are 9mm stitches)
· select the desired stitch
Screen
· selected stitch is highlighted
· suggests foot 1C; use foot No. 6 or No. 20C for heavy,
compact stitches
· basic settings (length and width) are automatically set,
but can be altered
Altering the stitch width
· alter the look of the stitch by adjusting the width
· turn the external stitch width knob to the right to
widen the stitch
· turn the external stitch width knob to the left to
narrow the stitch
· both the basic settings and the altered settings will be
visible on the screen
Altering the stitch length
· alter the look of the stitch by adjusting the length
· turn the external stitch width knob to the right to
lengthen the stitch
· turn the external stitch width knob to the left to
shorten the stitch
· both the basic settings and the altered settings will be
visible on the screen
Note:
Can also alter
· Stich width
· Needle position
·Tension
· Balance
Decorative stitches
TIP
Altering the basic settings
· the stitch can be adjusted as desired
· adjust the size of the stitch to suit the size of the item
being sewn, e.g, reduce the width for small items such
as doll clothes
Stitch:
Needle:
Thread:
Feed-dog:
Presser foot:
A B C
A decorative stitch with preset
width and length
B decorative stitch with reduced
width
C decorative stitch with shortened
length
185_NA_engl 16.4.2004 15:07 Uhr Seite 37
030866.51.04_0401_a185_EN
36
TIPS
Perfect corners
· activate Pattern end when approaching corner; when
the machine stops automatically, sink the needle (if
needed) and pivot the work
Monofilament hints
· if the monofilament thread breaks, sew more slowly
and/or reduce the upper thread tension slightly
Hand-look quilt stitch
Quilt stitches No. 328, 346–350
size and type suitable for the fabric selected
monofilament
30 weight, 2 ply cotton
up (sewing position)
Reverse pattern foot No. 1C or
Walking foot No. 50 (optional accessory)
Hand-look quilt stitch
· for all fabrics and all types of work where the look of a
hand sewn running stitch is desired
Sewing test
· the bobbin thread comes through to the top of the
fabric
·1 stitch is visible (cotton thread), 1 stitch is invisible
(monofilament thread) to give a hand stitched effect
Upper thread tension
· the upper thread tension is set automatically
· adjust if necessary to suit the fabric
Balance
· adjust if necessary
Sewing
· can be sewn with any needle position
Stitch:
Needle:
Upper thread:
Bobbin thread:
Feed-dog:
Presser foot:
Quilt stitches
185_NA_engl 16.4.2004 15:07 Uhr Seite 38
030866.51.04_0401_a185_EN
37
Quilt stitches
TIP
Perfect corners
· activate Pattern End; when the machine stops
automatically, sink the needle (if needed) and pivot the
work
Decorative quilt stitches
Quilt stitches Nos. 326–338, 351–353
size and type suitable for the fabric selected
cotton or rayon embroidery
up (sewing position)
Reverse pattern foot No. 1C
Straight stitch No. 326
·a short straight stitch (2mm)
· particularly suitable for piecing patchwork
Quilt stitches
· suitable for all fabrics and quilting
· especially applicable for crazy quilting
Balance
· adjust if necessary
Sewing
· select quilt stitch and sew
· all quilt stitches can be combined and programmed in
memory
Stitch:
Needle:
Thread:
Feed-dog:
Presser foot:
185_NA_engl 16.4.2004 15:07 Uhr Seite 39
030866.51.04_0401_a185_EN
38
TIPS
Freehand quilting and darning
· both techniques are based on the same free-motion principles
Thread breaks
· usually as a result of sudden or jerky movements – move the
fabric smoothly and at an even pace
Poor stitch formation
· if the thread forms loops, the work is being moved too quickly
· if knots are forming on the underside, the work is being moved
too slowly
Monofilament hints
· if the monofilament thread breaks, sew more slowly
and/or reduce the upper thread tension slightly
Freehand quilting
Straight stitch No. 1 or No. 325 Quilting straight sitch or
No. 326 Piecing stitch/Straight stitch
size and type suitable for the fabric selected
cotton or monofilament
down (darning position)
Darning foot No. 9 or Quilting foot No. 29C
Freehand quilting
·for all freehand quilt work
Preparation
· pin and baste top layer, batting, and lining together
· attach the slide-on sewing table or place machine in a
cabinet
Holding the work
· start in the center and work out toward the edges
· hold the fabric with both hands like an embroidery
frame
Quilting a design
· turn the work using smooth, round movements to form
the design of your choice (either freehand or following
a template)
Stipple quilting
· this technique covers the entire surface of the fabric
· the lines of stitching are rounded without any sharp
corners; they never cross or touch one another
Stitch:
Needle:
Thread:
Feed-dog:
Presser foot:
9
Quilt stitches
185_NA_engl 16.4.2004 15:07 Uhr Seite 40
030866.51.04_0401_a185_EN
39Combining decorative stitches with functions
9 mm decorative stitches
size and type suitable for the fabric selected
cotton or rayon embroidery
up (sewing position)
Reverse pattern foot No. 1C or
Open Embroidery foot No. 20C or
Embroidery foot No. 6 (optional accessory)
Clear foot No. 34/34C (optional)
Combining basic settings and functions
· you can achieve some exciting effects by combining
basic settings with various functions
Mirror image right/left
Mirror image – up/down
Pattern repeat 1–9 x
Half pattern
Balance
Long stitch function
Double needle limitation 2–8 mm
Wing needle limitation
Continuous reverse sewing
Pattern extend 2–5x
Balance
· use balance to obtain variations on stitches
· the stitch will be stretched open or compressed,
dependding on the number of balance steps
· for additional information on the balance function, see
pages 49–50
Method
· select function
· select stitch
· several functions can be activated for one
stitch
Deleting functions
·press the external clr button
· delete special functions individually by
touching the appropriate symbol
Stitch:
Needle:
Thread:
Feed-dog:
Presser foot:
Using decorative stitches with functions
TIPs
Variations with basic settings
and functions
· before starting a new
combination, clear all
functions previously used
Decorative stitches on single
layer fabric
· always use stabilizer
·remove stabilizer after
sewing
Activate needle stop down
when sewing long rows of
stitches
· needle stays in fabric when
stopping to reposition work
Single pattern
· the machine stops auto-
matically at the end of
each individual stitch
pattern
185_NA_engl 16.4.2004 15:07 Uhr Seite 41
030866.51.04_0401_a185_EN
40
Practical and decorative stitches in memory
Practical and decorative stitches in memory
· the memory capacity is 1023 individual stitch patterns
· the memory has 255 banks
· each bank can be sub-divided as desired
· most practical and decorative stitches as well as letters
and numbers can be combined, programmed, and
saved in memory
· exceptions: buttonholes, eyelets
· all saved stitches remain in the memory when the
machine is turned off
· all saved stitches and combinations can be recalled at
any time
Programming practical and decorative stitches
· open the memory by pressing the external mem button
· touch mem 1 to access the memory storage screen
· select an empty memory bank
· touch OK to return to the previous screen
· select the desired stitch
· the stitch appears in the memory bar
· select the next desired stitch
· continue in this manner until the desired combination
of stitches has been programmed
· to save, touch store
Example of programmed stitch combination
· select a memory bank following the directions above
· touch stitch 407 one time
· touch stitch 102 one time
· touch stitch 711 one time
· begin stitching; the stitches will continuously alternate
· to save, touch store
Examples of programmed stitch with function
· select a memory bank following the directions above
· touch stitch 413 one time
· activate mirror image – right/left
· touch stitch 413 one time
· begin stitching; the stitches will continuously alternate
facing up and down
· to save, touch store
· select a memory bank following the directions above
· touch stitch 104 one time
· activate mirror image – right/left
· touch stitch 104 one time
· begin stitching; the stitches will continuously alternate
facing up and down
· to save, touch store
185_NA_engl 16.4.2004 15:07 Uhr Seite 42
030866.51.04_0401_a185_EN
41Practical and decorative stitches in memory
Stitch combination as single repeat
· select a memory bank following the directions on the
previous page
· touch stitch 409 one time
· touch stitch 616 two times
· on the toolbar, activate Pattern repeat 2 x
· stitch; the machine stops automatically at the end of
the second combination of stitches
· to save, touch store
Stitch combination with mirror image as single repeat
· select a memory bank following the directions on the
previous page
· touch stitch 109 one time
· touch stitch 414 one time
· activate mirror image – up/down
· touch stitch 414 one time
· activate mirror image – right/left
· touch stitch 109 one time
· on the toolbar, activate Pattern repeat 1 x
· stitch; the machine stops automatically
at the end of the combination of stitches
· to save, touch store
TIPS
Decorative stitch combination with embroidery thread
· stitches appear fuller
Stitch combinations on single layer of fabric
· always use a stabilizer
·remove stabilizer after sewing
185_NA_engl 16.4.2004 15:07 Uhr Seite 43
030866.51.04_0401_a185_EN
42
Letters and numbers in memory
TIPS
Activate Pattern repeat 1 x after programming
· the machine will sew the program once and stop
Embroidering letters on a single layer of fabric
· always use stabilizer
·remove stabilizer after sewing
Practical and decorative stitches in memory
Programming letters and numbers
· open the memory by pressing the external mem button
· touch mem 1 to access the memory storage screen
· select an empty memory bank
· touch OK to return to the previous screen
· select the desired letter
· the letter appears in the memory bar
· select the next desired letter
· continue in this manner until the desired combination
of letters has been programmed
· to save, touch store
Examples of programming letters
· select a memory bank following the directions above
·press the external alphabet button
· touch the block letter alphabet
· touch the appropriate letters to spell “BERNINA”
· on the toolbar, activate Pattern repeat 1 x
· begin stitching; the letters will continuously stitch,
automatically stopping after the “A”
· to save, touch store
· for double length letters, select the Pattern extend 2x
function before programming
Examples of programming numbers
· follow the directions above for programming letters,
selecting numbers instead
· begin stitching; the numbers will continuously stitch,
automatically stopping after the last one
·to save, touch store
Examples of programming small monograms
· select a memory bank following the directions above
·press the external alphabet button
· touch the 9mm script alphabet
· touch the desired letters
· on the toolbar, activate Pattern repeat 1 x
· begin stitching; the letters will continuously stitch,
automatically stopping after the last one
· to save, touch store
Securing
· select the Securing function
· the first and last letters will be secured
· the memory capacity is 1023 individual stitch patterns
· the memory has 255 banks
· each bank can be sub-divided as desired
· most practical and decorative stitches as well as letters
and numbers can be combined, programmed, and
saved in memory
· exceptions: buttonholes, eyelets
· all saved stitches remain in the memory when the
machine is turned off
· all saved stitches and combinations can be recalled at
any time
185_NA_engl 16.4.2004 15:07 Uhr Seite 44
030866.51.04_0401_a185_EN
4316 directions
Straight stitch No.39 or Zig-zag No. 40
size and type suitable for the fabric selected
cotton or polyester
up (sewing position)
Sideways motion foot No. 40C
16 directional sewing
· for creative embellishment
· for quilting without turning the fabric
External button
·press the external Quilt/Directional button
· touch the 16 direction symbol
Stitch length and width
Straight stitch:
· the stitch length is generally 3 mm in all directions
Zig-zag:
· the stitch length is programmed to satin stitch
· it can be freely altered between 0mm and 1mm
· the stitch width can be freely altered between 0mm
and 9mm
Stitch:
Needle:
Thread:
Feed-dog:
Presser foot:
16 direction sewing
Thread tension
· the tension is automatically set when the 16 direction
program is selected
Screen
· Straight Stitch and Zig-zag appear
·a “compass” is in the center of the screen
·a presser foot is in the center of the compass
· the points indicate the 16 directions
· one touch to right or left = one step in the chosen
direction
· continuous pressing = faster direction change
·a long line indicates the direction selected
Sewing
· select the stitch
· adjust stitch width or length if required
· determine the direction on the compass
· the machine sews the selected stitch in the direction
chosen
Change direction
· stop the machine after sewing the desired distance
· select new direction on the compass
· sew
TIPS
16 directional sewing with embroidery thread
· stitches appear fuller
16 directional sewing on a single layer of fabric
· always use stabilizers a backing
·remove stabilizer after sewing
Embellishing with 16 direction sewing
· can be programmed in memory in combination with other stitches for truly
multi-directional embellishment possibilities
185_NA_engl 16.4.2004 15:07 Uhr Seite 45
030866.51.04_0401_a185_EN
44 16 directions
Straight stitch No. 39
Long stitch
size and type suitable for the fabric selected
cotton, polyester, or rayon
up (sewing position)
Sideways motion foot No. 40C
16 direction straight stitch as connecting threads
· long connecting threads between individual sideways
motion stitches or monogram letters
· connecting threads may be removed after sewing
Stitch length
· the length of the connecting stitches with the Long
stitch function is 9 mm (in all directions)
· it cannot be altered
Sewing
· select Straight Stitch
· select the desired direction on the compass
· activate the Long stitch function
· the machine sews long connecting stitches in the direc-
tion chosen
· clear the Long stitch function
Stitch:
Function:
Needle:
Thread:
Feed-dog:
Presser foot:
Connecting stitch patterns
TIP
All-over embellishment
· use this technique to embellish fabric in an all-over design
185_NA_engl 16.4.2004 15:07 Uhr Seite 46
030866.51.04_0401_a185_EN
454 directions
TIP
Patching fabrics that ravel
· finish the edges of the patch
· stitch just inside the edge of the patch
· do not trim the patch
4 directional sewing
Stitches No. 41–48
size and type suitable for the fabric selected
cotton or polyester
up (sewing position)
Sideways motion foot no. 40C
Automatic sewing in 4 directions
· sew in 4 directions without turning the fabric
· for adding patches to trousers, sleeves, and other
tubular items
Preparation for patches
· cut the patch slightly larger than the hole in the
garment
· position the patch on the fabric over the hole
Technique for decorative squares and patches
·press external quilt/directional button
· touch the 4 direction symbol
· select the desired stitch
· align the edge of the presser foot with one edge of the
patch and sew one side
· change direction with the right or left arrow
· sew the second side, etc.
· the best method for sewing
squares and rectangles is
from top to bottom and from
right to left (clockwise)
· trim the surplus fabric close
to the stitches
· trim worn area behind the patch
Using the Pattern repeat function
· activate Pattern repeat 1-9 x
· select desired stitch up to maximum 9 x
· each direction is sewn with the same number of
stitches
· it is recommended to sew clockwise
· another option is to save the desired number of stitches
in the memory
Stitch:
Needle:
Thread:
Feed-dog:
Presser foot:
185_NA_engl 16.4.2004 15:07 Uhr Seite 47
030866.51.04_0401_a185_EN
46 Sideways motion stitches
Sideways motion stitches/monograms
size and type suitable for the fabric selected
cotton or rayon embroidery
up (sewing position)
Sideways motion foot No. 40C
Sideways motion stitches
· outline designs, i.e. only the outer contours of the motif
are sewn
· monograms
· sideways motion stitches are indicated on the screen
with crossed arrows
Fabric feed
· the fabric is moved forward and backward in the usual
manner
· the fabric is also moved from side to side
Tension
· the tension is set automatically when the stitch is
selected
Size
· the size of sideways motion stitches cannot be altered
· monograms can be sewn in 3 different sizes (30/20/15 mm)
Stitch length and width
· the length and width of sideways motion stitches cannot be
altered
Balance
· the appearance of the stitches can be affected by the fabric,
stabilizer and thread quality
· balance can be used to adapt the stitch to the chosen fabric
· for additional information, see page 50
Sideways motion stitches and functions
· sideways motion stitches can be combined with all the functions
which appear on the screen, e.g. mirror image
Test sewing
· it is always worth test sewing with the materials you intend to
use – fabric, stabilizer and thread!
Template
· templates help you to position the motifs
· all sideways motion stitches are in their original size on the
template
(Exception: medium and small monograms)
·a circle shows the starting point
·a cross shows the end point
· there is a hole at the beginning and end to simplify marking
· the direction is indicated by a presser foot symbol and solid
guide lines
· the presser foot must always run parallel to the lines
· the templates are provided with the owners manual of the machine
No templates for medium and small monograms
· there is no template for these as they start and finish in a
straight line
· they are sewn as they are written
Stitch:
Needle:
Thread:
Feed-dog:
Presser foot:
Sideways motion stitches – Outline Designs
185_NA_engl 16.4.2004 15:07 Uhr Seite 48
030866.51.04_0401_a185_EN
47Sideways motion stitches
External button
·press the external Decorative stitch button
·press the external Alphabet button for monograms
Screen
· select any of the motifs marked with crossed arrows
· or select monograms
Sewing
· using the template mark the beginning of the stitch
on the fabric
· note the sewing direction
· insert the needle into the fabric at the beginning mark
· position the fabric so that the solid guide lines on the
template lines are parallel to the presser foot
· stitch; the machine sews the selected stitch and stops
automatically at the ending point
= START = END
artista 185
= START
= END
801
802
805
807
806
artista 185
= START
= END
811
812
814
816
826
813
artista 185
= START = END
1015
1022
1023
1026
1024
1025
1027
1028
artista 185
TIPS
Sewing sideways motion stitches on a large piece of fabric
· make sure that the fabric can move freely as the sideways
motion design is stitched
· if the feed is inhibited, the motif may not be stitched
properly
Sewing sideways motion stitches
· use a light touch, a finger tip feeding in guiding the fabric
· hold the fabric so that it is kept in vertical alignment
· avoid pulling the fabric
· draw parallel lines on the fabric with a fabric pen or
tailor’s chalk to aid in guiding
Sideways motion stitches and sewing table
· the slide-on sewing table is very useful when sewing
these stitches
Sideways motion stitches on a single layer of fabric
· always use a stabilizer
·remove stabilizer after sewing
· some sideway motion stitches can be sewn in a continuous row
185_NA_engl 16.4.2004 15:07 Uhr Seite 49
030866.51.04_0401_a185_EN
48 Sideways motion stitches
Sideways motion stitches in memory
Sideways motion stitches in memory
· all sideways motion stitches and monograms can be
programmed and saved in memory; however, they
cannot be sewn in sequence like decorative stitches
· the beginning and ending points of sideways motion
stitches vary considerably and are sometimes within the
stitch itself
Combining sideways motion stitches and monograms
in memory
· sideways motion stitches and monograms can be
combined with 16 directional stitching and saved in
memory
Open memory/program letter
·press external mem button
· select stitch
· the stitch appears in memory in the usual manner
Determine spacing with the template
· position the template with the selected letters,
e.g. F and G
· the sewing directions must correspond
· place the presser foot symbol of the 16 direction
template on the end point of the first letter
· the sewing directions must correspond
· note the direction to the starting point of the next
letter
· note the number of repeats (each 9 mm)
·program and save the direction and repeats in memory
· for more information, see pages 43-44
Program the second letter
·program the second letter
·program Pattern repeat function
· sew
Medium/small monograms
· medium and small monograms always start and finish
on a straight line
· they are sewn as they are written
TIPS
Sideways motion stitches and other stitches
·create delightful designs by combining individual sideways
motion stitches with other stitches
Sideways motion stitches and sewing table
· the slide-on sewing table is a real help when sewing these
stitches
185_NA_engl 16.4.2004 15:07 Uhr Seite 50
030866.51.04_0401_a185_EN
49Balance
All stitches are tested and adjusted before the machine
leaves the factory; however, shipping and transporting
can affect the setting of the balance function.
Different fabrics, threads and stabilizers can distort the
stitch patterns so that they are too long (do not close
properly) or too short (have a condensed appearance).
The electronic balance function can be used to correct
these distortions so that stitches can be adjusted for a
perfect formation on the fabric of your choice.
all stitches
all types, 70–110
all threads
up (sewing position)
as indicated on screen
Test sewing
· it is always a good idea to test sew with the materials
you intend to use – fabric, stabilizer and threads
Open balance
· touch the arrow on the functions toolbar
· scroll the functions
· touch “b”
· soft fabrics such as jerseys and tricot have a tendency
to stretch under the presser foot
· stitches such as Honeycomb may therefore not close
correctly
· this can be corrected with the balance function
Balance for practical stitches
· the stitch as it should look, e.g. Honeycomb, is in the
center of the screen
· possible stitch distortions are shown to the right and
left of the correct stitch
· the arrows at the bottom of the screen show in which
direction the stitch should be corrected
Note: the honeycomb stitch graphic will be seen
on-screen for all practical stitches
Corrections
· touch the appropriate arrow to balance the stitch
· the number of steps is shown above the arrow
· 2–5 steps are normally sufficient to balance practical
stitches (max. 50 steps)
Balance for 9 mm decorative stitches
· the method is the same as for practical stitches
Note: the satin stitched oval graphic will be seen
on-screen for all decorative stitches
Balance
Stitch:
Needle:
Thread:
Feed-dog:
Presser foot:
Balance for practical stitches/9 mm decorative stitches
balanced
stitch
open
stitch
overlapping
stitch
185_NA_engl 16.4.2004 15:07 Uhr Seite 51
030866.51.04_0401_a185_EN
50 Balance
Balance for sideways motion stitches
Fabric, thread stabilizers, and interfacings can affect
sideways motion stitches so correcting with balance will
sometimes be necessary.
Balance
· select sideways motion stitch or motif
· touch b to activate balance
· balance screen appears
· when balancing sideways motion stitches, the selected
motif is always shown
· the stitch appears in the center of the left half of the
screen
·two malformations are displayed either side of the
stitch – left too short and right too long
· the right half of the screen shows the horizontal
balance possibilities
Vertical corrections
· if the appearance of the sewn stitch is similar to the
one on the right of the screen, use the right arrow to
correct; the pattern will be shortened
· if the appearance of the sewn stitch is similar to the
one on the left of the screen, use the left arrow to
correct; the pattern will be lengthened
· 1–5 steps are normally sufficient to correct the stitch
vertically (max. 50 steps)
· if more than 10 steps are necessary, the stitch will
become smaller
· sew a test and make additional corrections if needed
Horizontal corrections
· the horizontal balance is shown in the right half of the
screen
· the stitch might possibly become too wide after vertical
corrections have been made, i.e. the center line of the
stitch becomes distorted
· if the center of the stitch has been pulled to the right,
correct with the left arrow
· if the center of the stitch has been pulled to the left,
correct with the right arrow
· 5–10 steps are normally sufficient to correct the stitch
horizontally (max. 20 steps)
· sew a test and make additional corrections if needed
Returning to stitch screen
· after all corrections are made, touch OK to confirm the
changes and return to the stitch screen
· touching reset will return the stitch to the same
condition as when the balance function was opened
If the stitch
looks like this,
use this arrow
to correct it.
Use these
arrows to
correct hori-
zontal distor-
tions
If the stitch
looks like this,
use this arrow
to correct it.
185_NA_engl 16.4.2004 15:07 Uhr Seite 52
030866.51.04_0401_a185_EN
51Index
16 directional sewing 43–44
4 directional sewing 45
A
Auto buttonholes 25
Auto round and keyhole
buttonholes 26
Automatic darning program 33
B
Balance for practical/
decorative stitches 49
Balance for sideways
motion stitches 50
Bar tack program 20
Basting 16
Blind hem 17
Button sewing-on program 29
Buttonholes 21–28
C
Contents 1
D
Darning programs 33–34
Darning, mending 31–32
Decorative stitches in memory 40–42
Decorative stitches with functions 39
Decorative stitches 35
Directional stitching 44
Double overlock seam 9
E
Edge stitching 4
Edges of knits with shirring elastic 31
Elastic, cord – sewing on 18, 19
Eyelets with straight stitch 30
Eyelets with zig-zag 30
F
Flat joining seam 10
Freehand quilting 38
G
Gathering stitch – sewing
on elastic/cord 18
H
Honeycomb stitch edges 12
J
Jersey overlock seam 9
L
Letters and numbers in memory 42
Long Stitch 15
M
Manual buttonholes 28
Manual darning 34
Memory – letters and numbers 42
Memory – practical and
decorative stitches 40–42
Memory – sideways
motion stitches 48
N
Numbers and letters in memory 42
O
Outline designs 46–47
P
Patches – sewing in 4 directions 45
Patches on knits and jersey 32
Personal (altered) memory 6
Practical stitch hems 11
Practical stitch seams 7–10
Practical stitches in memory 40–41
Q
Quilt stitches 38
Quilt/hand look stitches 36
R
Reinforced darning program 33
Reinforcing edges on woven fabrics32
Ribbing with overlock 13
Index
S
Securing stitch (straight stitch) 3
Sewing in 16 directions 43–44
Sewing in 4 directions 45
Sewing knits 12
Sideways motion stitches
in memory 48
Sideways motion stitches 46–47
Stitch counter buttonholes 27
Straight stitch buttonholes 24
Straight stitch with
securing program 3
Straight stitch 2
Stretch overlock seam 10
Stretch/Super stretch seam 8
T
Triple straight stitch seam 8
U
Universal stitch – sewing on elastic 18
V
Vari-overlock – ribbing 13
Vari-overlock seam 9
Z
Zig-zag stitch 5
Zippers 14
185_NA_engl 16.4.2004 15:07 Uhr Seite 53
030866.51.04_0401_a185_EN
04/01 EN 030 866 51 04
185_NA_engl 16.4.2004 15:07 Uhr Seite 54
030866.51.04_0401_a185_EN
132

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Bernina Artista 185 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Bernina Artista 185

Bernina Artista 185 Bedienungsanleitung - Deutsch - 138 seiten

Bernina Artista 185 Zusatzinformation - Holländisch - 40 seiten

Bernina Artista 185 Bedienungsanleitung - Holländisch - 137 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info