Bedienungsanleitung Bertazzoni CB36600X (Seite 8 von 28) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

605245

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

IMPORTANT INFORMATION CONCERNING THE INSTALLATION OF THE APPLIANCE

The hob can be installed by itself, in an isolated position or inserted between two kitchen units or between one kitchen unit

and a wall. Furthermore the back wall and surrounding surfaces must resist a temperature of 65 K.

To prevent the plastic layer which covers the kitchen unit from ungluing, the glue used to join the two surfaces together must

resist temperatures of up to 150 °C

The installation of the appliance must be carried out according to the norms in force of the country concerned and the

appliance must be installed in a well ventilated place.

This appliance is not equipped with devices to remove the products of combustion. The appliance must therefore be

connected following the norms for installation mentioned above. Special attention must be paid to the information below

regarding aeration and ventilation of the premises.

VENTILATION OF THE PREMISES

To guarantee that the appliance works correctly it is necessary that the place where the appliance is installed is continuously ventilated.

The volume of the premises must not be less than 25 m³ and the quantity of air needed must be based on the regular combustion of

gas and on the ventilation of the premises. The natural flow of air will take place through permanent openings made in the wall of the

premises to be ventilated: these openings will be connected to the outside and must have a minimum section of 100 cm² ( see Fig. 2 ).

These openings must be made in such a way that they cannot be obstructed.

POSITION AND VENTILATION

The cooking appliances that use gas must always remove the products of combustion via a hood linked to chimneys, chimney flues or

via a direct connection to the outside ( see Fig. 3 ). If it is not possible to fit a hood it is possible to use a fan, fitted on the window or

facing directly outside, which operates when the appliance is in use. ( see Fig. 4 ). In this way the norms in force of the country

concerned regarding the ventilation of premises are strictly followed.

BACKGUARD INSTALLATION INSTRUCTION

1) Remove n°2 screws fixing worktop as shown in fig.5

2) Place front part of the backguard and attach it from bottom side with the two removed screws (point 2) as shown in fig .6

3) Fix the front part of the backguard with the screws supplied with the backguard kit (fig.7)

4) Assemble back part with front part of the backguard and fix them with a screws supplied with the backguard kit (fig.8)

CONNECTING THE APPLIANCE TO THE GAS SUPPLY

Before connecting the appliance to the gas supply you first need to remove the plastic protective plug for the gas supply

which is inserted under pressure in the gas inlet connection. To remove the plug simply unscrew it.

Then make sure that the details shown on the label on the lower part of the case are compatible with those of the gas supply.

A label on the last page of this manual and on the lower part of the case indicates the conditions for regulating the appliance:

type of gas and pressure used.

IMPORTANT: This appliance must be installed in accordance with the norms in force of the country concerned and it must

only be used in a well-ventilated place.

ATTENTION: Remember that the gas inlet connection for the appliance is threaded 1/2 gas cylindrical male in accordance

with the norms UNI-ISO 228-1. (Fig. 10)

ADAPTING TO DIFFERENT TYPES OF GAS

Before carrying out any maintenance work, disconnect the appliance from the gas and electric supply.

- CHANGING THE NOZZLES FOR USE WITH OTHER TYPES OF GAS:

To change the nozzles of the burners use the following procedure:

Lift up the burners and unscrew the nozzles ( Fig. 9) using an adjustable spanner of 7 mm and change the nozzles with those designed

for the new gas supply according to the information given in TABLE N° 2 shown below.

ATTENTION: After carrying out the changes described above, the technician must put the label corresponding to the new gas

supply on the appliance to take the place of the old label. This label is found in the bag containing spare nozzles.

TABLE N°2: Adapting to different types of gas APPLIANCE CATEGORY: II2H3+

Burner

Types of Gas

Pressure

Nozzle

Diameter

Rater Capacity

Reduced

Capacity

by-pass

Diameter

mbar

1/100 mm.

g/h

l/h

kcal/h

1/100 mm.

Natural G20

860

0,48

413

34 reg.

Auxiliary

Butane G30

860

0,48

413

Propane G31

860

0,48

413

Natural G20

101

167

1,75

1505

0,6

516

36 reg.

Semi-Rapid

Butane G30

127

1,75

1505

0,6

516

Propane G31

125

1,75

1505

0,6

516

Natural G20

129

286

2580

1,05

903

52 reg.

Rapid

Butane G30

218

2580

1,05

903

Propane G31

214

2580

1,05

903

Dual

Natural G20

0,8

688

0,48

413

34 reg.

Inner

Butane G30

0,8

688

0,48

413

Propane G31

0,8

688

0,48

413

Dual

Natural G20

2x110

419

4,4

3784

1,8

1548

65 reg.

Outer

Butane G30

2x69

298

4,1

3526

1,8

1548

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bertazzoni CB36600X Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info