Bedienungsanleitung Bertazzoni P9101PROX P91 (Seite 9 von 41) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

612648

Zoom out

Zoom in

Vorherige Seite

1/41

Nächste Seite

1) Turn on the burner and put the knob onto position MINIMUM ( small flame ).

2) Remove the knob ( Fig. 8) of the tap which is set for standard pressure. The knob is found on the bar of the tap itself.

3) Beside the tap bar on the work top, use a small screwdriver that fits the screw (gold) found on the lower part of the tap (auxiliary,

semirapid, rapid Fig. 8) (dual fig.9) and turn the fixing screw to the right or left until the flame of the burner is regulated in the most

suitable way to MINIMUM.

4) Make sure that that the flame does not go out when changing the position quickly from MAXIMUM to the MINIMUM position.

ATTENTION: The regulation described above can be carried out only with burners using methane gas and city gas ( where

available), while with burners using liquid gas the screw must be fully screwed in, in a clockwise direction.

CONNECTION OF THE APPLIANCE TO THE ELECTRICITY SUPPLY:

Connection to the electricity supply must be carried out according to the norms and indications of the law in force.

Before carrying out the connection check that:

- The electric charge of the system and the sockets are suitable for the maximum power of the appliance ( see label on the lower part

of the case ).

- The socket or system is equipped with an efficient earth connection according to the norms and indications of the law currently in

force. No responsibility can be held if these indications are not respected.

When the connection to the electricity supply is made with a socket.

Fit onto the electric cable a standard plug ( if it is not provided ) which is appropriate for the charge indicated on the label. Connect up

the wires according to the diagram in Fig. 10 taking care to respect the corresponding pairs listed below:

letter L (phase) = brown coloured wire;

letter N (neutral) = blue coloured wire;

symbol” ” earth = green-yellow coloured wire;

- The electric cable must be positioned so that it cannot reach a temperature of over 75 K at any point.

- Do not use reducers, adapters or shunts for the connection as they could cause false contacts and subsequent dangerous

overheating.

When the connection is made directly with the electricity supply:

- Make sure that there is a device to disconnect the appliance from the mains with a contact opening distance sufficient for complete

disconnection in category III overvoltage conditions.

- Place a single-pole switch between the appliance and the electricity supply. The switch must be of a suitable charge for the appliance

with a minimum opening between the contacts of 3 mm.

- Remember that the earth wire must not be interrupted by the switch.

- Alternatively the electrical connection can also be protected by a differential switch of high sensitivity.

- You are strongly advised to fix the special yellow-green earth wire to an efficient earthing system

ATTENTION:

The appliance conforms to the EEC indication 90/396 regarding gas cooking appliances for domestic use.

All our appliances are designed and produced according to the European norms EN 60 335-1 and EN 60 335-2-6 and

additional relative amendments. The appliances conform with the indications of the European Low Tension Directive 73/23

and 93/68 as well as conforming with the indications of the European directive 89/336 regarding electromagnetic

compatibility.

MAINTENANCE OF THE MACHINE

CHANGING THE PARTS

Before carrying out any maintenance work, disconnect the appliance from the gas and electric supply.

To replace different components such as burners, taps and electrical parts you must take out the hob from the kitchen unit by

releasing the fixing hooks, unscrew the fixing screws of the burners on the work top, unscrew the fixing nuts of the electric plates which

are visible on the lower part of the hob and remove the worktop in order to carry out the replacement of the defective parts.

NOTE: If the taps need replacing you also need to unscrew the two fixing screws of the gas ramp at the bottom of the hob which are

found on the upper part of the latter.

For appliances equipped with automatic “ON” switches you must dismantle the “ON” switch chain before replacing the taps.

You are advised to change the seal on the tap every time you replace a tap in order to ensure a perfect hold between the body and

ramp.

WARNING: The electric cable which is provided with the appliance is connected to the appliance with a type X connection (in

accordance with the norms EN 60335-1, EN 60335-2-6 and successive variations) and thus can be replaced with the same type of

cable as that installed without using special tools.

In the event of wear or damage to the mains cable, replace it following the indications shown below in table n°3:

TABLE N° 3: Types and sections of the electric mains cable for hobs

Dimensions of hob

Type of hob

Type/ section of mains cable

59 x 50 cm.

86 x 50 cm.

gas burners

H05RR-F 3x0,75 mm2

WARNING: If you replace the electric mains cable the installer must have the earth conductor about 2 cm longer than the

phase conductors and must also take heed of the warnings regarding electric connection.

Oiling the taps: (This must be carried out by qualified staff from a technical assistance centre)

If a tap becomes difficult to move you must oil the tap, without delay, following the instructions given below:

1) Dismantle the main part of the tap by unscrewing the two screws that can be found on the bar of the tap itself. (Fig. 11)

2) Take out and clean the holding cone and its setting with a cloth soaked in diluent.

3) Oil the cone lightly with the special oil.

4) Insert the cone, move it a few times, take it out again, remove the excess oil and make sure that the areas where the gas flows are

not obstructed.

5) Reassemble all the pieces in the reverse order to that followed for the dismantling and check that the tap is working properly.

Bertazzoni P9101PROX P91 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info