Bedienungsanleitung Bertazzoni PM365S0X-B (Seite 4 von 16) (Englisch, Französisch)

605252

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

VENTILATION OF THE PREMISES

To guarantee that the appliance works correctly it is necessary that the place where the appliance is installed

is continuously ventilated. The volume of the premises must not be less than 25 m³ and the quantity of air

needed must be based on the regular combustion of gas and on the ventilation of the premises. The natural

flow of air will take place through permanent openings made in the wall of the premises to be ventilated:

these openings will be connected to the outside and must have a minimum section of 100 cm² ( see Fig. 4 ).

These openings must be made in such a way that they cannot be obstructed.

POSITION AND VENTILATION

The cooking appliances that use gas must always remove the products of combustion via a hood linked to

chimneys, chimney flues or via a direct connection to the outside ( see Fig. 5A ). If it is not possible to fit a

hood it is possible to use a fan, fitted on the window or facing directly outside, which operates when the

appliance is in use. ( see Fig. 5B ). In this way the norms in force of the country concerned regarding the

ventilation of premises are strictly followed.

CONNECTING THE APPLIANCE TO THE GAS SUPPLY

Before connecting the appliance to the gas supply you first need to remove the plastic protective

plug for the gas supply which is inserted under pressure in the gas inlet connection. To remove the

plug simply unscrew it.

Then make sure that the details shown on the label on the lower part of the case are compatible with

those of the gas supply.

A label on the last page of this manual and on the lower part of the case indicates the conditions for

regulating the appliance: type of gas and pressure used.

IMPORTANT: This appliance must be installed in accordance with the norms in force of the country

concerned and it must only be used in a well-ventilated place.

ATTENTION: Remember that the gas inlet connection for the appliance is threaded 1/2 gas

cylindrical male in accordance with the norms UNI-ISO 228-1. (Fig. 6-7)

CONNECTION OF THE APPLIANCE TO THE ELECTRICITY SUPPLY:

Connection to the electricity supply must be carried out according to the norms and indications of

the law in force.

Before carrying out the connection check that:

- The electric charge of the system and the sockets are suitable for the maximum power of the appliance (

see label on the lower part of the case ).

- The socket or system is equipped with an efficient earth connection according to the norms and indications

of the law currently in force. No responsibility can be held if these indications are not respected.

When the connection to the electricity supply is made with a socket.

Fit onto the electric cable a standard plug ( if it is not provided ) which is appropriate for the charge indicated

on the label. Connect up the wires according to the diagram in Fig. 8 taking care to respect the

corresponding pairs listed below:

letter L (phase) = brown coloured wire;

letter N (neutral) = blue coloured wire;

symbol”

” earth = green-yellow coloured wire;

- The electric cable must be positioned so that it cannot reach a temperature of over 75 K at any point.

- Do not use reducers, adapters or shunts for the connection as they could cause false contacts and

subsequent dangerous overheating.

When the connection is made directly with the electricity supply:

- Place a single-pole switch between the appliance and the electricity supply. The switch must be of a

suitable charge for the appliance with a minimum opening between the contacts of 3 mm.

- Remember that the earth wire must not be interrupted by the switch.

- Alternatively the electrical connection can also be protected by a differential switch of high sensitivity.

- You are strongly advised to fix the special yellow-green earth wire to an efficient earthing system

ATTENTION: The appliance conforms with the regulations of directives 90/396EEC (Gas Directive)

regarding gas appliances for domestic use and the like, 93/68 and 73/23 (Low Voltage Directive) regarding

electrical safety and 2004/108/CE, 93/68 and 89/336 (EMC Directive) regarding electromagnetic

compatibility.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bertazzoni PM365S0X-B Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info