Bedienungsanleitung BeSafe iZi Go X1 - 2015 (Seite 3 von 98) (Alle Sprachen)

652125

Zoom out

Zoom in

Vorherige Seite

1/98

Nächste Seite

10 11

•Carrying handle (1a)

•Head cushion (1b)

•Handle release buttons (2x) (1c)

•Shoulder straps (2x) (1d)

•Hip belt hook (2x) (1e)

•Baby cushion (1f)

•Harness buckle (1g)

•Sun canopy (1h)

•Pushchair release handles (4x) (1i)

•Shoulder belt hook (1j)

•Harness height adjuster (1k)

•Pushchair adapter housing (1l)

Preparing to install

Installation of the seat on the ISOﬁx base

Removal of the seat of the ISOﬁx base

Belt installation

1. Always check if the ISOﬁx indicators are green, before positioning

the seat on the base. (2)

2. Position the seat in the correct position on the base untill it clicks

with the base and the indicator at the front shows green. (3)

3. Leave the carrying handle up in the carrying position.

4. When the seat is positioned rearfacing on the back seat of the

vehicle, you should, if possible, push the front seat of the vehicle

backwards, so that it is in contact with the child seat. If it is not

possible to obtain contact with the child seat, push the back rest

of the front seat of the vehicle forward as far as possible. (4)

•The seat can be taken o by pulling the seat release handle at the

front of the base.

1. Position the seat on the vehicle seat. Make sure the carrying handle

is up in the carrying position. (5)

2. Guide the hip belt of the 3-point-belt over the blue sections under

the hip belt hooks and fasten the seat belt with a ‘click’. (6)

3. Guide the shoulder belt over the blue section through the shoulder

belt hook at the rear side of the seat shell. (7)

4. Tighten the 3-point belt by pulling the belt through the hip belt

hooks and through the shoulder belt hook until it is as tight as

possible. (8)

5. Leave the carrying handle up in carrying position.

Positioning of the child

Baby cushion

1. Check that the shoulder strap slots are level with your child’s

shoulders. (9)

2. Pull the shoulder straps up while pressing the button of the central

adjuster. (10)

3. Open the harness buckle. (11)

4. The height of the shoulder straps and the head cushion can be

adjusted by pulling the release handle upwards at the back of the

seat and pulling the handle up or down. (12)

5. Position the shoulder straps over the marking at the sides of the seat

to use the magnets to keep the harness open while you position the

child. (13)

6. When the child is positioned, place the shoulder straps over the

child’s shoulders and close the buckle: CLICK! (14)

7. Pull the harness strap through the central adjuster in the direction of

the arrow straight up/forwards. Continue pulling until the harness is

a comfortable but a ﬁrm ﬁt. (15)

8. You can protect your child against the sun by raising the sun canopy.

The baby cushion oers extra comfort for young babies. As baby grows

the thickness of the baby cushions can be adjusted.

•0-4 m (16)

•4-6 m (17)

•6 m + (18)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

BeSafe iZi Go X1 - 2015 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info