Bedienungsanleitung BeSafe iZi Twist B i-Size (Seite 4 von 115) (Alle Sprachen)

768221

Zoom out

Zoom in

Vorherige Seite

1/115

Nächste Seite

12 13

• The child seat MUST NOT be installed in a front

passenger seat WITH AN ACTIVATED AIRBAG.

• The ﬂoor support must always be used. Make sure that the

ﬂoor support is fully pushed down and that the seat is positioned

horizontal with the spirit level in the middle.

• Never drive with a child in the seat if the seat is rotated to the side.

• Make sure the indicators are green before you drive.

! Warning: potential misuse

• Do take care when you remove the cover, as re-ﬁtting the cover is

done in reverse.

• The cover of the headrest can be taken o separately by

disconnecting the beads at the back and pulling o the fabric

towards the front.

door of the vehicle is too small, which might lead to a situation

where the seat is not positioned correctly on the vehicle seat.

Removing and reﬁtting the cover

Baby insert

Baby cushion

1. The baby insert must be used from birth and can be used until a

stature height of 87 cm. Don’t take the baby insert out before the

baby can sit upright by itself.

2. The baby insert can be taken out of the seatshell, by guiding the

harness through the slots of the baby insert.

3. The baby insert can be positioned back in the seatshell, by guiding

the harness through the slots of the baby insert. Use the baby insert

only in the most reclined position of the seat. Make sure the harness

is positioned correct, so the harness can be pulled tight without

twisting. (15)

1. The baby cushion oers extra comfort for young babies.

2. < 60 cm (16)

3. > 60 cm (17)

1. Turn the seat towards the door while you pull the rotation release

handle upwards.

2. Check that the shoulder strap slots are level with your child’s

shoulders. (7)

3. While pressing the button of the central adjuster, pull the shoulder

straps away from the seat with a ﬂat hand. Make sure to pull the

straps evenly so that they stay at the same length. (8)

4. Open the harness buckle. (9)

5. The height of the shoulder straps and the headrest can be adjusted

by pulling the release handle upwards at the back of the headrest and

pulling the headrest up or down. (10)

6. Position the shoulder straps over the marking at the sides of the seat

to use the magnets to keep the harness open while you position the

child. (11)

7. When the child is positioned, place the shoulder straps over the child’s

shoulders and close the buckle: CLICK! (12)

8. Pull the harness strap through the central adjuster in the direction of

the arrow straight up/forwards. Continue pulling until the harness

is a comfortable but a ﬁrm ﬁt. (13)

9. Turn the seat against the driving direction before driving and check if

the release handles show green and the seat is locked into the driving

direction. (14)

Positioning of the child

1. To remove the seat from the vehicle, turn the seat rear facing

and push the seat upwards while adjusting the ﬂoor support to its

shortest length.

2. Release the ISOﬁx connectors out of the seat by pushing down

the switch for the ISOﬁx connectors on both sides. Pull the ISOﬁx

release switch on both sides to disconnect from the ISOﬁx car

anchorage.

Removal of the seat from the vehicle

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

BeSafe iZi Twist B i-Size Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info