Bedienungsanleitung Bestron AAC12000 (Seite 45 von 88) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Schwedisch)

800735

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

Cooling

1. Press the “MODE” button (Figure 1-F) once or more times, until the indicator light “COOL” lights up. The

device will now function as an air cooler and will cool the air by means of a cooling element.

2. Use the “UP” (Figure 1-D) “DOWN” (Figure 1-E) buttons to set the cooling temperature between 16 °C

and 31 °C.

3. Press on the “FAN” (Figure 1-C) button to switch between low or high speed for discharged air.

ATTENTION:

• When the internal water collector is full, the appliance stops operating and the indicator light on the

control panel lights up “FULL”. You must empty the water collector before you can use the appliance

again (see ‘CLEANING AND MAINTENANCE - Water drainage’).

• If you frequently use the appliance to dehumidify or cool air, you can also use the continuous discharge

(see ‘CLEANING AND MAINTENANCE - Water drainage’).

USE - Sleep mode

The device is equipped with a sleep mode. Enabling this function will allow the appliance to operate at its

quietest and most energy efficient setting

ATTENTION:

The sleep mode only works in the “COOL” mode.

1. Press the buttons “FAN” and “UP” (Figure 1-C and D) to enable the sleep function. The device switches

to the lowest and most energy-efficient setting.

2. Press the “FAN” and “UP” buttons again to disable the sleep function.

ATTENTION:

After switching off the sleep function, the device will remain in “COOL” mode.

USE - Timer mode

The device is equipped with a timer that allows you to switch the device on or off automatically.

Automatic power-on

When the appliance is switched off:

1. Press the “TIMER” button (Figure 1-B). The display starts to flash.

2. Use the button UP/DOWN to set the switch-on time between 1 and 24 hours.

3. Wait for the display (figure 1-A) to stop flashing. The switch-on timer is set.

4. Press the button again “TIMER” to adjust the switch-on time if necessary.

5. When the displays flash, press the button “TIMER” to turn off the timer.

Automatic power-off

When the appliance is switched on:

1. Press the “TIMER” button (figure 1-B). The display starts to flash.

2. Use the UP/DOWN button to set the power-off time between 1 and 24 hours.

3. Wait for the display (figure 1-A) to stop flashing. The power-off timer is set.

4. Press the “TIMER” button again to adjust the power-off time if necessary.

5. When the displays flash, press the “TIMER” button to turn off the timer.

USE - Remote control

The device can also be operated using the remote control included. The remote control works on two AAA

batteries (not included). Open the battery compartment on the bottom, insert the batteries and close the lid.

The buttons on the remote control function the same as the buttons on the control panel.

For optimal use:

• Make sure the distance between the device and the remote control does not exceed 6 metres.

• Point the remote control at the device and ensure the direction angle is less than 30 degrees.

• The remote control has an extra button “SWING” to engage swing mode and move the airflow from top

to bottom. In addition, the slats can be adjusted to a desired position.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bestron AAC12000 Seite 45

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info