Bedienungsanleitung Bestway 58259 (Seite 7 von 92) (Alle Sprachen)

752356

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

RESET BUTTON

IMPORTANT INSTRUCTION FOR USING

If the water temperature has not changed 4-5 hours after activation of the heating system, use a thin object to press

the RESET BUTTON, and restart the heating system.

IMPORTANT: The heating system will not operate if the outside temperature is above 40°C (104°F) or if the Pool

Heater is under direct sunlight. Under these conditions, please wait until a cooler time of day before pressing the

RESET BUTTON with a thin object and restart the heating system.

NOTE: To order spare parts for the Pool Heater, please provide us with part no. and part name.

Drawings for illustration purposes only. May not reflect actual product. Not to scale.

RESET

P6124

Hose

Clamp P6176

Hose

P6005 O-Ring

Filter Pump

Above Ground Pool

Water Level

Sand Filter

P6124

Heating Reset

1. Be sure to press the "Reset" button on the

pool heater using a small and thin object before

initial operation

2. If the pool heater is not heating properly, press the "Reset"

button on the pool heater.

Operation

NOTE: Check the pool for correct installation and make sure both the pool’s

Inlet and Outlet Valves are fully covered with water before operating the Filter

Pump or Sand Filter with the Pool Heater. Make sure that the Pool Heater and

Filter Pump or Sand Filter are correctly connected.

1. Start the Filter Pump or Sand Filter according to the owner’s manual.

2. With the pump operating, insert the plug of the Pool Heater into a socket,

after test PRCD . The LED will light up for 0.5 seconds with a “beep” sound,

and the LED displays .

3. Press the “POWER” button for 2 seconds, the LED turns on and the heater

starts to work, the LED display .

4. Press the “POWER” button for 2 seconds again, the Pool Heater will turn off.

NOTE: When the water temperature reaches the maximum temperature

40°C (104°F), the LED turns green.

NOTE: Never plug in the Pool Heater until the Filter Pump or Sand Filter has

been plugged in.

WARNING: To prevent the risk of electrical shock, ensure your hands are

completely dry when plugging-in the Filter Pump or Sand Filter and the Pool

Heater.

NOTE: To prevent the risk of electrical shock, never run the Filter Pump or

Sand Filter and the Pool Heater when people are in the pool.

NOTE: Do not dry run the Pool Heater. Damage caused by dry running the

Pool Heater is not covered by the manufacturer’s warranty.

5. Remember to disconnect the Pool Heater first. Never unplug the Filter Pump

or Sand Filter when the Pool Heater is running.

6. Unplug the Filter Pump or Sand Filter and enjoy warm pool water!

Maintenance

CAUTION: YOU MUST UNPLUG THE POOL HEATER FIRST, THEN

UNPLUG THE FILTER PUMP OR SAND FILTER BEFORE PREFORMING

MAINTENANCE OR SEVERE RISK OF INJURY OR DEATH EXISTS.

1. Stop Water Flowing to the Filter Pump or Sand Filter and the Pool Heater:

a) Disconnect the Pool Heater and THEN the Filter Pump or Sand Filter.

b) Loosen the Hose Clamps on the pool’s Inlet and Outlet Hoses.

c) Replace the Debris Screens with the Stopper Plugs in the pool’s Inlet and

Outlet Valves.

d) Refer to the Filter Pump or Sand Filter ’s Owner’s Manual for information

on Filter Pump or Sand Filter maintenance.

2. After Filter Pump or Sand Filter maintenance, replace the Stopper Plugs with

the Debris Screens in the pool’s Inlet and Outlet Valves. Water will now flow

to the Filter Pump or Sand Filter and the Pool Heater.

3. Operate as outlined in the Operation section of this manual.

Storage and Winterization

CAUTION: YOU MUST UNPLUG THE POOL HEATER AND THE FILTER

PUMP OR SAND FILTER BEFORE MAINTENANCE BEGINS OR SEVERE

RISK OF INJURY OR DEATH EXISTS.

To avoid damage, pool equipment must be winterized when temperatures are

lower than 4°C (40°F). Allowing water to freeze will damage the Pool Heater

and void the warranty.

NOTE: Do not leave the heater out in the open air for long periods of time.

When it is not in use, please clean and dry it and then store it in a cool, dry

place.

1. Follow the instructions previously outline to stop water flowing to the Filter

Pump or Sand Filter and the Pool Heater.

2. Detach all hoses.

3. Drain any water in the Pool Heater and clean all components thoroughly.

4. Put the Pool Heater in a cool, dry place, out of children’s reach.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bestway 58259 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bestway 58259

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info