Bedienungsanleitung Bestway 60025 Helsinki (Seite 16 von 252) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Finnisch)

809083

Zoom out

Zoom in

Vorherige Seite

1/252

Nächste Seite

The WATER HEATER rate may change in the conditions below:

• When the outdoor temperature is below 15°C (59°F).

• If the cover is not in position. Always keep the spa cover on when the spa is not in use; it avoids dust contaminating the water and it minimizes heat

loss.

• The water temperature shown on the display may not be correct, if the filtration system is not activated. To read the correct water temperature on the

display, run the filtration system for at least a minute.

• The water temperature as tested by an external thermometer may vary from the temperature as displayed on the spa panel by as much as

approximately 2°C (35.6°F).

HEATING TIME

• To reach 40°C (104°F), the heating duration required is based on the starting water temperature and ambient temperature, the data below is purely for

reference. To display the current water temperature, run the filter system for at least a minute.

• Be sure to cover the spa with the spa cover whenever the heating function is activated. Leaving the spa uncovered will increase the heating duration

required. When the spa is assembled with water, do not switch off the spa heater if the temperature is lower than 6ºC (42.8°F).

WATER FILTER BUTTON: The button turns the filter pump on and off. The button turns to red when activated.

TEMPERATURE ADJUSTMENT BUTTONS: Pressing the or button, the display starts to flash showing the set temperature for

3 seconds, after that it will show again to the real water temperature. When it is flashing you can adjust the temperature using the or

button.

The default temperature is 35°C (95°F).

Temperature adjustment ranges from 20°C (68°F) to 40°C (104°F).

ON/OFF BUTTON: After activating the PRCD, press and hold the button for 2 seconds. The button turns to green and the control

panel is activated. Press and hold button for 2 seconds to turn off all currently activated functions.

CELSIUS/FAHRENHEIT TOGGLE: The temperature can be displayed in either Fahrenheit or Celsius.

FOR SPA EQUIPPED WITH Wi-Fi ONLY

Wi-Fi ACTIVATION: For the Wi-Fi operation instruction, read the spa Wi-Fi instruction leaflet included in the package.

WINTER USE INSTRUCTIONS

SPA HEATER SPECIFICATION

Ambient Temperature

10ºC (50ºF)

15ºC (59ºF)

20ºC (68ºF)

25ºC (77ºF)

30ºC (86ºF)

Water Temperature

10ºC (50ºF)

15ºC (59ºF)

20ºC (68ºF)

25ºC (77ºF)

30ºC (86ºF)

Set Temperature

40ºC (104ºF)

Heating Duration

16-24h

12-20h

10-18h

8-12h

5-8h

Power Rate Massage Tube Power Heat Element Power Water Pump Power

2,000W at 20ºC 50W

220-240V AC, 50/60Hz,

Single Phase 2,050W at 20ºC 800W

It is important to follow these suggestions if you are setting up the spa during the winter period. This will prevent any damage to the spa

heater and material of the liner, extending the life of your product drastically.

• If the outdoor temperature is below 10°C (50°F), to avoid any damage to spa liner, keep the package indoors where the temperature is above

15°C (59°F). This will make the spa liner more flexible and easier to set up.

• Open the package and inflate the spa liner using the spa heater in a room where the temperature is above 15°C (59°F).

• Position the spa liner outdoors in the desired position, then connect the spa heater and fill with water. The water temperature used to fill the spa must be

above 6°C (42.8°F), otherwise when you begin to operate with the spa heater, the E03 alarm will appear.

• You can keep the spa on during winter when the temperature is lower than 6°C (42.8°F). The Freeze Shield™ system automatically keeps the water

temperature between 6°C (42.8°F) and 10°C (50°F), and it will prevent the water from freezing.

• If the water temperature is below 6°C (42.8°F), the spa heater must always be on. In this mode, the Freeze Shield™ system can keep the internal

temperature between 6°C (42.8°F) and 10°C (50°F) to prevent damage, such as water freezing in the pipes or the circulation system.

• If any alarms appear on the display, the Freeze Shield™ system isn’t working. Be sure to check the status of your spa if the outdoor temperature is

below 6°C (42.8°F). In case of a long-term absence from home when there is a risk of temperatures falling below 6°C (42.8°F), we strongly suggest

disassembling the spa and storing it following the storage procedure.

• Any damage as a result of using the spa in these conditions is the responsibility of the customer. Do not use the spa when the ambient temperature

reaches -10°C (14°F).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bestway 60025 Helsinki Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bestway 60025 Helsinki

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info