Bedienungsanleitung Bestway 60025 Helsinki (Seite 20 von 252) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Finnisch)

809083

Zoom out

Zoom in

Vorherige Seite

1/252

Nächste Seite

1. Unplug the plug gently, strike the side of the pump but not violently, and plug it

back in.

2. For assistance, please visit the support section on our website,

www.bestwaycorp.com.

CAUSES REASONS SOLUTIONS

The water flow sensors work

without pressing the filter or heat

button.

1. The water flow sensor flags didn’t fall back into the

correct position.

2. The water flow sensors are broken.

After starting or during the

functions of filtering or/and

heating, the water flow sensors do

not detect water flow.

1. You forgot to remove the 2 stopper caps from

inside the pool.

2. Filter cartridges are dirty.

3. Activate the filter or heat system and put your

hand in front of the outlet pipe inside the pool to

check if you can feel water flowing out.

a. If no water flows out the water pump is broken.

b. Water flows out but the alarm appears,

the water flow sensors are broken.

4. Filter blockage

5. Bent pipes or poor water flow through the plastic

pipes of the liner

6. Debris screens are blocked: Debris screens can

become blocked by hard water due to calcium

build-up.

7. Perished washers

The washers within the spa couplings may have

become perished or worn.

1. Remove the 2 stopper caps before heating. Refer to the Assembly section in

the User’s Manual.

2. Remove the filter set from inside the pool and push the filter or heat button. If

no alarm appears, clean or change the filter cartridges installed inside the pool.

3. For assistance, please visit the support section on our website,

www.bestwaycorp.com.

4. Clean the filter and check for damage. Replace or re-install as necessary. For

assistance, please visit the support section on our website,

www.bestwaycorp.com.

5. Please check through the spa connection to see if the pipes are bending. For

assistance, please visit the support section on our website,

www.bestwaycorp.com.

6. Empty the spa and place a garden hose inside the pipes to wash the debris. To

be sure all debris are removed, perform the operation from the outside and

inside of the spa.

Use a toothbrush to remove any stubborn debris.

For assistance, please visit the support section on our website,

www.bestwaycorp.com.

7. Check the washers inside the coupling for damage. Unscrew the couplings and

remove the washer for further inspection.

For assistance, please visit the support section on our website,

www.bestwaycorp.com.

The pump’s thermometer reads

the water temperature below

4°C (40°F).

1. The water temperature is lower than 4°C (40°F)

2. If the water temperature is higher than 7°C (44.6°F),

the pump’s thermometer is broken.

1. The spa is not designed to operate with water temperatures lower than 4ºC

(40°F). Unplug the pump and only re-start the pump when the water

temperature reaches 6°C (43°F).

2. For assistance, please visit the support section on our website,

www.bestwaycorp.com.

The pump’s

thermometer reads the water

temperature over 50°C (122°F).

1. The water temperature is over 50°C (122°F)

2. The ambient temperature is higher than 40°C (104°F)

or the spa is exposed to direct sunlight for an extended

period of time.

3. If the water temperature is lower than 45°C (113°F),

the pump’s thermometer is broken.

1. The spa is not designed to operate with water temperatures greater than

40°C (104°F). Unplug the pump and only re-start the pump when the water

temperature reaches 38°C (100°F) or lower.

IMPORTANT: Before you re-start the pump, push the pump’s reset button.

2. Disconnect the plug, detach the pump and drain the spa. After 15 minutes,

reattach the pump, reconnect the plug and restart the heating function. If the

alarm appears again, consider moving the spa to another location without

direct sunlight.

3. For assistance, please visit the support section on our website,

www.bestwaycorp.com.

The pump’s

thermometer

connection has issues.

1. The pump’s thermometer connectors don’t work

properly.

2. The pump’s thermometer is broken.

For assistance, please visit the support section on our website,

www.bestwaycorp.com.

The thermal cut-out

cut off.

The manual reset thermal cut-out trips off. 1. Unplug the pump and push the reset button, then plug the pump back in.

2. In case the alarm still remains, check the RESET BUTTON section in manual.

3. For assistance, please visit the support section on our website,

www.bestwaycorp.com.

Ground connection failed. 1. The ground bonding of your home has some

problem.

2. The pump has some problem.

For assistance, please visit the support section on our website,

www.bestwaycorp.com.

Wi-Fi module is damaged For assistance, please visit the support section on our website,

www.bestwaycorp.com.

NOTE: Press any button to remove alarm and continue to use the spa.

Wi-Fi module connection failed.

ERROR CODES

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bestway 60025 Helsinki Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bestway 60025 Helsinki

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info