Bedienungsanleitung Beurer HT 80 (Seite 13 von 60) (Deutsch, Englisch, Französisch, Italienisch, Spanisch, Polnisch, Türkisch)

620035

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

• Do not use the device on synthetic hair – risk of ﬁ re!

Note

• Remove all packaging material before using the device.

• Only connect the device to a socket using the voltage speciﬁ ed on the type plate.

• If you do not know the local mains voltage, request it from the relevant organisation.

• Only pull the mains cable from the socket by the mains plug.

• Do not use any additional parts that are not recommended by the manufacturer or o ered as accessories.

• Under no circumstances should you open or repair the device yourself, as faultless functionality can no

longer be guaranteed thereafter. Failure to comply will result in voiding of the warranty.

• In the event of a fault or damage, have the device repaired by a certiﬁ ed specialist workshop.

• Never leave the device unattended during use.

• Do not use the device outside.

• If you pass on the device to someone else, make sure to also pass on these instructions for use.

6. Operation

Warning

• Position yourself on a dry, non-conductive surface. Risk of electric shock!

• Make sure that your hands are dry! There is a risk of electric shock!

• The heated brush [3], the curling brush [2] and the device may become very hot depending on the switch

setting and period of use – risk of burns and ﬁ re! Do not touch the heated brush [3] or the curling brush [2].

• Place the device on ﬁ reproof surfaces only. Risk of ﬁ re!

• Ensure that no hair can be directly sucked into the device. Risk of ﬁ re!

Important

• Do not jam the mains cable [11] in drawers or doors, for example.

• Untangle the mains cable [11] if it is twisted.

• Do not pull, twist or bend the mains cable [11] and do not pull or route it over/on sharp, pointed objects or

hot surfaces.

Note

A slight odour initially develops after switching on the device for the ﬁ rst time. This is normal and not harmful

to your health. Allow the device to run for three to ﬁ ve minutes. After that you can use the device as normal.

• For your safety, the device switches o automatically if it overheats.

• Pull the mains plug out of the socket and allow the device to cool down.

• Before switching the device back on, check the air outlet [4] and the air intake ﬁ lter [8] for any blockages

(e.g. sucked-in ﬂ u , dust or hair).

6.1 General instructions for use

Step 1: Attaching/removing the brush attachment

> To attach a brush attachment to the hot air brush, place the required brush

attachment on the hot air brush and carefully turn it right and left until you see

and hear it click in place.

> To remove a brush attachment from the hot air brush, hold down the unlock

button [1] on the brush attachment and pull the attachment o the hot air

brush.

> Allow the heated brush [3] and the curling brush [2] to cool before you remove

them.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Beurer HT 80 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Beurer HT 80

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info