Bedienungsanleitung Beurer IH 18 (Seite 17 von 72) (Deutsch, Englisch, Französisch, Italienisch, Spanisch, Polnisch, Türkisch)

568811

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

10. Troubleshooting

Problem/Ques-

tion

Possible Cause/Remedy

The atomiser

produces

little or no

aerosol.

1. Too much or too little medicine

in the atomiser.

Minimum: 0.5 ml,

Maximum: 6 ml.

2. Check that the nozzles are not

blocked If necessary, clean

the nozzle (e.g. by rinsing).

Use the atomiser again.

CAUTION: Only poke imple-

ments through the fine holes

from the underside of the

nozzle.

3. The atomiser is not held in an

upright position.

4. The medicine solution is

unsuitable for nebulising (e.g.

too thick).

The medicine solution should

be specified by the doctor.

Output is too

low.

Hose kinked, filter blocked, too

much inhalation solution.

Which

medicines are

suitable for

inhalation?

Consult your doctor.

Essentially all medicines that

are suitable and approved for

device-based inhalation can be

inhaled.

Some inhalation

solution

remains in the

atomiser.

This is normal and occurs for

technical reasons. Stop inhala-

tion if you hear a notable differ-

ence in the noise of the atomiser.

What special

steps should be

taken for babies

and children?

1. In babies, the mask should

cover the mouth and nose to

guarantee effective inhalation.

2. In children, the mask should

also cover the mouth and

nose. Nebulisation next to a

sleeping person is not suitable

because insufficient medicine

reaches the lungs.

Note: Children should only use

the device with help and under

supervision of an adult. Never

leave a child alone with the

nebuliser.

Inhalation with

the mask takes

longer.

This is for technical reasons.

Less medicine is inhaled per

breath through the mask holes

than using the mouthpiece. The

aerosol is mixed with ambient air

through the holes in the mask.

Problem/Ques-

tion

Possible Cause/Remedy

Why do I need

to replace the

atomiser at

regular inter-

vals?

There are two reasons for this:

1. To guarantee a therapeutically

effective particle spectrum,

the nozzle holes should not

exceed a certain diameter.

Due to the thermal and me-

chanical stresses, the plastic

is subjected to a certain

amount of wear. The nozzle

attachment [8] is particularly

susceptible to this wear. This

can also cause changes to

the droplet composition of the

aerosol, which has a direct ef-

fect on the effectiveness of the

treatment.

2. You are also recommended

to replace the atomiser on

a regular basis for hygiene

reasons.

Does each per-

son need their

own atomiser?

This is absolutely necessary for

hygiene reasons.

11. Technical specifications

Dimensions

(WxHxD)

160 x 155 x 84 mm

Weight 1,2 kg

Operating

pressure

approx. 0,66-1,1 bar

Atomiser fill

volume

max. 6 ml

Medicine flow > 0.2 ml/min.

Sound pressure < 60 dBA

(acc. to DIN EN 13544-1 section 26)

Mains

connection

230 V ~, 50 Hz; 180 VA

Housing material ABS

Operating

conditions

Temperature: +10 °C – +40 °C

Relative humidity: 10% – 95%

Storage and

transport

conditions

Temperature: -20 °C – +70 °C

Relative humidity: 10% – 95%

Atmospheric pressure: 500 – 1060 hPa

Subject to technical modifications.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Beurer IH 18 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Beurer IH 18

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info