Bedienungsanleitung Beurer IH26 (Seite 15 von 88) (Deutsch, Englisch, Französisch, Italienisch, Spanisch, Polnisch, Türkisch)

653522

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

5. Initial use

Positioning the device

Take the device out of the packaging.

Place the device on a flat surface.

Make sure that the vents are free from obstructions.

Before using the device for the first time

Note

•

Clean and disinfect the atomiser and accessories

before using them for the first time. See “Cleaning

and disinfection” on page

•

Connect the compressed air hose [8] to the bottom

of the medication container [12].

•

Connect the other end of the compressed air hose

[8] to the nebuliser hose connection [4] by turning it

slightly.

Power supply

The device must only be connected to the mains volt-

age that is specified on the type plate.

•

Insert the mains plug of the mains connector cable

[3] into a suitable socket.

•

To connect to the mains, fully insert the mains plug

into the socket.

Note

•

Ensure that there is a mains socket close to the set-

up area.

•

Arrange the mains connector cable so that no-one

will trip over it.

•

To disconnect the nebuliser from the mains after in-

halation, first switch off the device and then pull the

mains plug out of the socket.

6. Operation

Important

•

For hygiene reasons, it is essential to clean the at-

omiser [9] and the accessories after each treatment

and to disinfect them after the last treatment of the

day.

•

The accessories may be used only by one person;

use by several people is not recommended.

•

If the therapy involves inhaling several different medi-

cations one after the other, please be aware that the

atomiser [9] must be rinsed under warm tap water

following every usage. See “Cleaning and disinfec-

tion” on page 17.

•

Please observe the notes on changing the filter in

these instructions for use.

•

Check that hose connectors are firmly attached to

the nebuliser [4] and the atomiser [9] before each use

of the device.

•

Before use, check the device is working correctly, by

briefly switching on the nebuliser (together with the

connected atomiser, but without medication). If air

comes out of the atomiser [9], the device is working.

6.1 Installing the atomiser insert

• Open the atomiser [9] by twisting the top anticlock-

wise against the medication container [12]. Place

the atomiser insert [10] into the medication container

[12].

• Ensure that the cone for administering medication fits

well on the cone for the air duct inside the nebuliser.

6.2 Filling the atomiser

• Fill with an isotonic saline solution

or pour the medication directly in-

to the medication container [12].

Avoid overfilling. The maximum

recommended filling quantity is

8ml.

• Use medication only as instructed

by your doctor and ask about the

appropriate inhalation period and

quantity for you.

• If the prescribed quantity of medication is less than

2 ml, top this up to at least 4 ml with isotonic sa-

line solution. Dilution is also necessary with viscous

medications. Here too, please observe the instruc

tions of your doctor.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Beurer IH26 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info