Bedienungsanleitung Beurer JIH50 (Seite 18 von 76) (Deutsch, Englisch, Französisch, Italienisch, Spanisch, Polnisch, Türkisch)

533571

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

Drying

•

Carefully dry all components using a soft cloth.

•

Shake the mesh atomiser (3) lightly backwards and

forwards (5 to 10 times), so that the water inside

the mesh is removed from the small holes.

•

Place the individual components on a dry, clean

and absorbent surface and allow to dry completely

(for at least 4 hours).

Note

Ensure that all parts are thoroughly dried after cleaning,

otherwise there is an increased risk of bacterial growth.

Once all components are fully dry, reassemble the

nebuliser and place the components in a dry, sealed

container.

Ensure that the mesh atomiser (3) has dried completely

by shaking it. Otherwise, nebulisation may not function

properly after reassembling the device.

If this is the case, disassemble the mesh atomiser (3)

again and shake it so that the water can escape. Once

it has been reassembled, the nebuliser should function

properly again as usual.

Material resistance

•

When choosing a cleaning or disinfecting agent,

note the following: Only use mild cleaning or disin-

fectant agents in the quantities recommended by

the manufacturer.

•

As with all plastic components, frequent use and

cleaning of the atomiser and the accessories can

lead to a certain amount of wear. Over time, this

can alter the aerosol properties and may eventually

affect the efficiency of therapy. We therefore rec-

ommend that you replace the atomiser and acces-

sories at least once a year.

Storage

•

Do not store the nebuliser in a damp atmosphere

(e.g. in the bathroom) or transport it together with

damp objects.

•

Store and transport the nebuliser away from direct

sunlight.

Troubleshooting

Problem/

Question

Possible Cause/Remedy

The nebuliser

produces little

or no aerosol.

. Insufficient medicine in the

atomiser.

. The atomiser is not held in an up-

right position.

. The medicine used is unsuitable

for spraying (e.g. too thick, viscos-

ity must be less than 3).

The medicine solution should be

specified by the doctor.

Problem/

Question

Possible Cause/Remedy

Output is too

low.

. The batteries are flat. Replace the

batteries or connect the power

supply unit and try again.

. There are air bubbles inside the

medicine container which are pre-

venting the medicine from coming

into continuous contact with the

mesh. Please check and remove

any air bubbles.

. Particles on the mesh are imped-

ing output. To remove the par-

ticles, fill the nebuliser with 2 to

3 drops of vinegar and 3 to 6 ml

of water, then nebulise this solu-

tion completely. Do not inhale this

spray and ensure that you clean

and disinfect the medicine con-

tainer afterwards (see page 16).

If the output does not improve, re-

place the mesh.

4. The mesh is worn out.

Which medi-

cines are suit-

able for inhala-

tion?

Only the doctor can advise you

which medicine to use to treat your

condition. Consult your doctor.

With the JIH 50, you can atomise

medicines with a viscosity lower

than 3.

Some inhala-

tion solution

remains in the

nebuliser.

This is normal and occurs for techni-

cal reasons. Stop inhaling as soon

as you can hear a marked differ-

ence in the sound made by the at-

omiser, or when the device switches

off automatically due to insufficient

inhalant.

What special

steps should

be taken for

babies and

children?

1. In babies, the mask should cover

the mouth and nose to guarantee

effective inhalation.

2. In children, the mask should also

cover the mouth and nose. Nebu-

lisation next to a sleeping person

is not suitable because insufficient

medicine reaches the lungs.

Note: Children should only use the

device with help and under supervi-

sion of an adult. Never leave a child

alone with the nebuliser.

Inhalation with

the mask takes

longer.

This is for technical reasons. Less

medicine is inhaled per breath

through the mask holes than us-

ing the mouthpiece. The aerosol is

mixed with ambient air through the

holes in the mask.

Does each user

need their own

accessories?

This is absolutely necessary for hy-

giene reasons.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Beurer JIH50 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Beurer JIH50

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info