533688
14
Zoom out
Zoom in
Vorherige Seite
1/80
Nächste Seite
14
1
. Press the ON/OFF button to start treatment.
If the safety lock is not turned to the closed position, the device cannot be switched
on.
2
. Select the desired speed using the speed controller.
3
. Select the desired direction of rotation using the buttons for clockwise and anti-clockwise
rotation.
4
. Do not press too hard and always carefully move the attachments towards the area to be tre-
ated. Move the device towards the area to be treated and apply slight pressure while slowly
moving the device in circles.
If a large amount of pressure is placed on the rotating attachment, the device automa-
tically switches off. Press the ON/OFF button again to switch the device back on.
5
. Apply moisturiser to the treated areas after each use.
5. Cleaning
Warning
Before beginning cleaning, always pull the mains adapter out of the socket!
•
Clean the base station and the hand-held device with a damp cloth. If it is very dirty, you can
also moisten the cloth with a mild soapy solution.
•
For hygienic reasons, you may use alcohol and a cloth or brush to clean the attachments. Al-
low the attachments to dry afterwards.
•
Do not use any chemical or abrasive cleaning agents.
•
Ensure that no water enters the device. If this should happen, reuse the device only when it
has fully dried out.
•
Do not submerge the base station and mains adapter in water or any other fluids.
6. What if there are problems?
Problem Possible cause Solution
Hand-held device will
not switch on.
Mains adapter not plugged in Insert the mains adapter into the
socket.
No voltage at mains socket Check your fusebox.
Hand-held device not connected to
base station.
Connect the hand-held device to
the base station.
7. Replacement parts and wearing parts
Replacement parts and wearing parts are available from the corresponding listed service
address under the stated material number.
Replacement part Material number
Fine sapphire cone 163.301
Coarse sapphire cone 163.302
Felt cone 163.303
sapphire wheel (fine) 163.304
Sapphire wheel, coarse 163.305
Cylindrical cutter 163.306
Flame-shape cutter 163.307
14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Beurer MPE 100 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info