Bedienungsanleitung BH Fitness G-6488 (Seite 19 von 71) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

542482

Zoom out

Zoom in

Vorherige Seite

1/71

Nächste Seite

MAINTENANCE.-

Use the bottle of lubricant (12) to

lubricate the inside of the belt in order

to keep your unit in top condition and

to ensure that friction between the belt

and the board is kept to a minimum

(due to different running styles, always

apply more lubrication to the area

where you place your feet during the

exercise) It is advisable to lubricate

the base of the belt every 3-12 months

Fig.8, depending on how often it is

used.

If the belt starts to slip after lubrication,

then check the tension of the belt. To

tension the belt, take the 6 mm Allen

key and with the machine set to 4

km/h turn screws (R & L) one turn in a

clockwise direction.

Operating

speed

Recommended lubrication

period

1~6 km 1 year

6~12 km 6 months

12~16 km 3 months

ADJUSTING THE BELT.-

If your unit is not seated evenly on the

four contact points, this may cause the

belt (X) to shift sideways. Rigorous

quality control adjusts and checks the

running belt. However, due to weight

differences and individual styles of

running, the belt may be prone to shift

sideways.

If the belt does shift to the left or right,

stop the machine.

BELT OFFSET TO THE RIGHT.-

This procedure is very important.

Follow these steps. In order to adjust

the belt, set the unit in motion at a

speed of 4 km/h. If the belt has moved

to the right, turn screw (R) Fig.9 on the

right-hand side of the machine a 1⁄4

turn clockwise. Note the position of the

belt, if after one minute the belt is not

completely centred then repeat the

operation. If you see that the belt has

moved too far over to the left then turn

the right screw back slightly in an

anticlockwise direction. Fig.9.

As soon as you have adjusted the belt

you can begin exercising again.

BELT OFFSET TO THE LEFT.-

In the event that the belt has moved to

the left, turn screw (L) Fig.9 on the

left-hand side of the machine a 1⁄4

turn clockwise. Note the position of the

belt, if after one minute the belt is not

completely centred then repeat the

operation. If you see that the belt has

moved too far over to the right then

turn the left screw back slightly in an

anticlockwise direction. Fig.9.

Important: Overtightening of the belt

can lead to a loss of speed on the

machine and even stretch the belt

itself. Bear In mind that one turn of the

right screw (R) in a clockwise direction

has the same effect on the position of

the belt as one turn of the left screw

(L) in an anticlockwise direction.

Consequently, in the event of

excessive belt movement you can use

either of the two screws in order to

avoid overtightening the belt.

OPERATING INSTRUCTIONS.-

FITNESS.

Being fit means living life to the full.

Modern society suffers greatly from

stress. City life is basically sedentary.

There are too many calories and too

much fat in our diet. All doctors agree

that regular exercise is a good way to

control our weight, make us fitter and

help us to relax.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

BH Fitness G-6488 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info