Bedienungsanleitung Bianchi 2021 (Seite 90 von 233) (Alle Sprachen)

779863

Zoom out

Zoom in

Vorherige Seite

1/233

Nächste Seite

ENGLISH

REPAIRS

Flat tyre

In case of a ﬂ at tyre, Bianchi advises you to:

1. Remove the wheel.

2. Remove the tyre completely from the wheel, proceeding as

follows:

2a. From one side of the rim, lift up a short section by grabbing it on

the side diametrically opposite the valve and separate the tyre from

the rim. If the sidewall is too difﬁ cult to remove, use a cycle tyre

lever with extreme care.

2b. Remove the inner tube.

2c. Check very carefully its outer and inner surface and remove the

object that caused the ﬂ at tyre. If the tyre is cut, line the hole from

the inside (using a piece of cloth, adhesive tape, a piece of inner

tube, a piece of cardboard, etc.).

2d. Repair the inner tube using the special kit or replace it if

necessary.

2e. Reassemble the tyre and inner tube, starting out by inserting

a side of the tyre into the rim groove. Insert the valve (without

fastening it) and the inner tube slightly inﬂ ated. Beginning from

the valve and working on both sides of the rim, insert the second

sidewall being careful not to “pinch” the inner tube.

2f. Make sure the tyre and the inner tube are properly assembled

and that the base of the valve is correctly positioned between the

two sides of the tire.

2g. Pump the inner tube slowly to the pressure indicated on the side

of the tyre, checking that its sides stay inside the rim.

2h. Screw on the valve fastening nut ﬁ rmly by hand and reposition

its cap.

3. Reassemble the wheel.

Broken spoke

A broken spoke weakens the wheel and makes your bicycle

dangerous to use.

Should this happen, Bianchi advises you to proceed with caution

after carrying out some simple checks:

1. Wind the broken spoke around the nearest spoke to prevent it

from ﬂ apping around or getting tangled in the frame.

2. Turn the wheel by hand one complete turn to make sure the rim

is not off-center and does not touch the brake pads. If it does, turn

the brake cable adjustment screw clockwise to widen the pads. If

the problem persists, open the brake quick-release (thus making it

unusable) and fasten the loosened cables.

3. Get off the bicycle and avoid riding it. If this is not possible, pedal

slowly and only use the brake that acts on the undamaged wheel.

DANGER / SAFETY NORM:

The operation of only one brake does not guarantee safe braking

distances. In case of a broken spoke or another problem that

causes one brake to stop working, Bianchi advises against riding

your bicycle. In case this is not possible, be extremely careful to

avoid damages or serious injury to yourself and to others.

All Bianchi products comply with European standards.

MAINTENANCE OF YOUR NEW REPARTO

CORSE BICYCLE

All maintenance operations described in this Handbook and in the

relevant table (see “Maintenance Table”) can be carried out by

anyone with basic mechanical knowledge and skills. In case of

doubt, or if you require additional explanations, Bianchi invites you

to contact your specialist Dealer.

Any other maintenance and repair jobs must be carried out by

qualiﬁ ed personnel at a specialist mechanical shop.

DANGER / SAFETY NORM:

Any adjustments, maintenance and repairs not carried out in a

workmanlike manner can be very dangerous for your safety and

the safety of others.

Running-in

Prior to subjecting your new Bianchi Reparto Corse bicycle to

extended stresses, it is advisable to put it through a running-in

period: this will guarantee long-lasting performances and better

operation in general.

After the bicycle is used a few times, the control cables and the

wheel spokes experience some adjustments and may need to be

recalibrated.

After using the bicycle for 30/60 days, take it to your Specialist

dealer for the ﬁ rst check-up.

After that, the perfect operation of the frame and control

components can be ensured by complying with the instructions

provided in the Maintenance Table below.

In case of particularly frequent or difﬁ cult riding, either on the

road or off, the periodical checks indicated in this manual must be

carried out more often.

For any malfunctioning problem related to maintenance conditions,

Bianchi invites you to contact your trusted Dealer.

WARNING / IMPORTANT:

The frame and components of a bicycle have different life cycles in

relation to the structure, the assembly materials, the frequency and

type of use to which they are subjected.

Bianchi invites you to follow a suitable maintenance program, and

recommends that you have a specialist Dealer check the condition

of the frame and of the control components of your new Reparto

Corse bicycle.

FUNCTIONAL

CHECKS

Bianchi invites you to

constantly monitor the

overall conditions of your

new Reparto Corse bicycle,

making sure that all parts

and accessories are

safely fastened. Bianchi

also suggests some

simple operations to carry

out in order to periodically

check the functional state

of the bicycle, speciﬁ cally

the frame and control

components.

Braking system

In order to check for

proper operation of the

braking system, pull the

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bianchi 2021 Seite 90

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info